Question about 1992 Dodge Spirit

1 Answer

I'm trying to find where the idle switch is located in the engine. I believe it is too low and i need to turn it up.

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

I dont think there is one i believe that it is all electronic

Posted on Jul 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I cheat the Idle up? I'm getting a low oil pressure light at Idle, 800 RPM. I would like to increase the Idle to 1000 to keep from getting the light.


that wont work trying to adjust idle can be done on older cars with a carburetor or the older throttle bodies new vehicles trying to do it will set off check engine lights on most sensors sound more like oil worn out---oil filter or pump problem change oil and filter and do a flush ---and put in an additive such as lukas - royal purple etc---also why did head need replacing was oil pump tested

Aug 02, 2016 | 2006 Suzuki Forenza

3 Answers

Oil light on after engine warm-up on idle


this means a mechanical gauge test is required to check actual pressure warm idling if low below 20 psi then the oil pressure pump relief is stuck open or engine bearing are worn

May 15, 2014 | 2005 Opel Astra 1.4

1 Answer

My 1995 geo prism stalls when turning left


100 % left or partial , not right?
on a hot or cold engine block.? or both.
no other symptoms, no engine power loss. up tall hills.
no loss of idle speed, 800 normal, 400 rpm not.
many suzukis have a P/S limit switch that sends a command to
the ECU (EFI) to raise idle due to driver overloading (dont) the P/S
by slamming it into the stops.
in very extreme temperatures (air) the idle can be too low.
like in Nunavut , Canada? and this switch can come in handy.
when RPMs are hard to control on a cold engine.'
no location stated.

Dec 11, 2012 | 1995 Geo Prizm

2 Answers

My 1989 cadillac idiles low but once I turn the wheel it cuts off


remove and clean the IAC idle air control it is probably sticking and giving a low idle. or replace it if need be. it should idle at about 7-800 rpms, i think thats why it quits when you turn the wheel. it is putting more stress on the pump and the engine. check idle. Good-day !

Aug 25, 2011 | Cadillac Brougham Cars & Trucks

2 Answers

My car vibrates,but dont when i have the a/c off


this means that your idle when the aircon is off is very low. basically there are 2 adjustments for idle: engine idle and aircon idle. just try to locate this screws in your engine. set the engine idle at 700-800rpm, while the aircon idle at 900-1000rpm.

Aug 05, 2011 | 1996 Ford Crown Victoria

3 Answers

When turn on the heat/AC, the car stall immediately


This is normally caused by your cars idle up. The idle up engages when you turn on the AC and that will add few RPM for your engine to prevent your engine from stalling. A replacement is needed to fix the problem. You may also check for the vacuum routing sticker on your hood. If you have a vacuum routing sticker on your hood, refer to that. The hose from the IAC valve routes to the Idle Up switch (as you know) the other hose from the idle up switch routes to the passenger end of the intake plenum, right on the end of it toward the firewall side. Don't confuse rubber heat shield on hose for hose size.

Jan 01, 2011 | 2000 Toyota Camry

1 Answer

Vw 1992 oil pressure drops when warmed up oil pressure switch was replaced still have same prblem light comes on at idle and goes off when engine speed is increased


Hook up a manual oil pressure guage and take readings of the actual amount of oil pressure in the engine. It may be that the switch is bad even though it is new. It may also be that you have low enough oil pressure at idle to trip the switch. On my 2.0 liter the low oil switch turns on at 4.4 PSI at idle but when the engine is revved up it turns on below 26 PSI. You may also have 2 oil pressure switches, one for low and one for high. They would be located very close together on the oil filter housing. Make sure you replaced the right switch.
You want to get this straightened out quickly as VW engines are very unforgiving when you put off repairs. Hope this helps.

Jul 12, 2010 | 1992 Volkswagen Golf

2 Answers

Low Idle and O2 sensor replacement on Montero


The O2 sensor is mounted to the exhaust; you'll need to get under the truck (jack-stand please) to locate. If it sits where a 89-92 sits it will be in the exhaust under the passenger side. Follow the wiring, on most it carries over the transmission to a wiring block under the driver's sie of the truck (again this is all under the truck) As for the low idle I do not believe there is anything to be change. If the idle is low it is due to other conditions... injectors, sensor, low compression, timing or such.
I hope this may have helped,
Tom

Jul 02, 2009 | 1996 Mitsubishi Montero

4 Answers

Nissan ga15 engine idle adjustment locations


The idle speed is computer controled, it is not adjustable, you most likely have sludge in the throttle valve and the idle speed control air bypass valve, clean them with carb spray with the engine running.

Sep 17, 2008 | 1996 Nissan Sentra

1 Answer

95 accord with low idel with A/C on


The idle air control valve should be located directly behind and a little bit below the Fuel rail that supplies the injectors depending on the date of manufacture. If it is not located there, look straight off the passenger end of the fuel rail. In any case it should be locate immediately after and in the fuel path after the unused fuel leaves the fuel rail to return to the tank.

Jun 22, 2008 | 1995 Honda Accord

Not finding what you are looking for?
1992 Dodge Spirit Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...