Question about 2005 Chrysler PT Cruiser

Open Question

Orginally had a p0340 code replaced the cam sensor in my 06 pt cruiser now have code p0344 engine light on again and bucks going down the road

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

Ad
  • 15 Answers

SOURCE: 2002 pt cruiser Camshaft Sensor

change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Posted on Mar 04, 2009

  • 9 Answers

SOURCE: My 2003 pt cruiser won't turn over.

could be ignition relays, starter solenoid...

Posted on Apr 27, 2009

  • 15 Answers

SOURCE: code 344 camshaft sensor ciurcut intermitint 05 pt cruiser

check you tps sensor throttle postion sensor

Posted on Jun 03, 2009

  • 94 Answers

SOURCE: 02 PT Cruiser LE w' Code P0340

My thought is to get a refund from the shop that tried to replace parts in order to secure your problem. The job of the shop is to diagnose the problem, not to replace items that may be the problem. Chrysler Master Techs are not trained to just replace parts, they fix the problem by diagnosing it properly.

You need to see a Chrysler dealership so they can attach a DRBIII and tell you exactly what is at stake.

I hope this helps you. I would be mad as heck.

I would not think the plugs and wires would be the problem because they would all have to fail at the same time to provide the symptom you experienced.

1. Get your money back
2. DRBIII

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0340 code and p0344 on 3.7 dodge Dakota


First check the easy thing. Have your battery tested. Sensors very sensitive to failing battery. If the battery tests fine then you will need to change the Cam sensor probably a $30 part. On your truck remove the air filter housing & the cam sensor should be easily accessible at the front of the cyl head. Hope this works for you. Based on your P codes it should.

Mar 25, 2014 | 2004 Dodge Dakota

1 Answer

Neon Code P0344


I believe that the splice for the cam sensor is about 8 inches back in the harness. Power to the cam supplies several sensors. I have fixed a few that the splice was bad, There is very little room to work in to get to the splice, but it's not impossible to fix.

Jul 13, 2013 | 2004 Dodge Neon

1 Answer

My 2002 pt cruiser died while I was driving first the oil light came on then it just died! I just had the oil changed 3 days prior to it dying some of the codes I received were 0340 1684 1685...


P0340 is cam position sensor. P1685 is for the key(has a chip in it) P1684 is battery has been disconnected. If the engine will still crank then codes P1684 & P1685 are probably old codes. So if the car will still crank, lets forget about those codes and focus on P0340 A bad cam position sensor will cause the engine to die and not allow it to start back up. Replace the cam position sensor and clear the code and the car should start up.

Oct 16, 2012 | Cars & Trucks

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

2 Answers

Code P0340 & P0344 car was running then i turned it off to put my key back on chain and tried to start itr again and it wont start


These codes indicate a possible camshaft position sensor failure, however a defective crank sensor can set these codes as well, due to the fact that both sensors share some of the same circuitry. I would highly recommend a powertrain control module update first, reference TSB# 18-026-03 before any parts replacement. Your local Chrysler dealer can perform this update.

Jan 23, 2011 | 2003 Chrysler PT Cruiser

2 Answers

I am having a p0340 and a p0344 code coming on and the check engine light is on. The car is maknig a jerking sensation when driving.Also, the car is not accelerating like it use to and the driving...


P0340 Camshaft Position (CMP) Sensor Circuit
P0344 Camshaft Position Sensor Circuit Intermittent


You'll need to replace the Camshaft Position Sensor and might as well replace the crankshaft sensor as well. With these codes and the symptoms you describe this should clear the problem for you. Also check the wiring harness around both sensors to make sure there are no issues. Maje sure no insulation is cut or missing along the entire run of the associated wiring.

Aug 24, 2010 | 2003 Chrysler PT Cruiser

1 Answer

Getting code P0340, No camshaft position sensor signal at PCM, should I replace sensor or go straight to timing belt


Replace the cam sensor with a factory sensor. Aftermarket sensors can still trigger the light when nothing is wrong.

Oct 24, 2009 | 2003 Chrysler PT Cruiser

1 Answer

My 2003 pt cruiser won't turn over.


could be ignition relays, starter solenoid...

Apr 19, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...