Question about 2008 Mitsubishi Galant

Open Question

How do I program the homelink in my 2008 Mitsubishi Galant?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello -My 2008 Galant has an AC problem It has quit cooling and the AC light flashes


his may indicate that you have a problem with your a/c system. light a gas leak. try to recharge the system and see what it does.

Feb 28, 2011 | 2008 Mitsubishi Galant

1 Answer

What kind of oil do i use for my 2008 galant 2.4


MOST NEWER VEHICLES RUN 5W -20 THAT SHOULD FINE BUT NOT THICKER THAN 10W-30

Dec 25, 2010 | 2008 Mitsubishi Galant

1 Answer

My Mitsubishi Galant 2008 2.4L reads AMP ECOM on the dash then the message goes and nothing is affected in the car.. what does this message mean?


My 2004 mitsubishi galant radio stop working and displayed a e comm message after getting a new battery installed, how do I get the radio to work?? please help

Oct 27, 2010 | 2008 Mitsubishi Galant

1 Answer

What do i need to do to get a replacement key for my 2008 galant which i bought used in Dec and only came with one key?


these if i remember are programmable keys which unfortunatly can only be bought at a mitsu dealer

Aug 12, 2010 | 2008 Mitsubishi Galant

1 Answer

How to set up garage door opener on my 2002 diamante


Detail Instructions from the owner's manual 1. Turn off engine
2. Prepare transmitter by erasing all three of the factory default channels by holding down the two outside buttons until the red light begins to flash. Release both buttons.
3. Hold the end of your hand-held transmitter (garage door remote) against the Homelink transmitter keeping the red light within the Homelink icon in view.
4. Using both hands push the hand-held transmitter button and the deisre button to be programmed on the Homelink transmitter. Do not release the buttons at this time.
5. Hold down both buttons until the red light on the universal transmitter flashes, first slowly then rapidly. When the light flashes rapidly, release both buttons.
To program the remaining two buttons, follow steps 3-5.

Jan 17, 2010 | 2002 Mitsubishi Diamante

3 Answers

PROGRAM PRIUS GARAGE DOOR HOW DO I PROGRAM THE BUTTONS ON THE PRIUS' REAR VIEW MIRROR TO OPEN THE GARAGE DOOR


There was a minor change for mine to work.. see below..

- you must park your Prius close to the gate opener, leaving it running (obviously not in the way of the gate closing)
- Hold the button the the mirror and then push your garage door remote button and hold until the light on the mirror starts to flasyh fast. THIS programs the button on the mirror, but not the garage opener - yet (this was key for me)
- locate the "learning button" on the opener itself
- press the "learning button" on your gate opener and then get back into the Prius within 30 seconds (more time than it sounds) and press the SAME Homelink button you just programmed above. I don't recall how long I held the pre-programmed button, but the light will flash as I recall.
- Then, when working the garage door, you may need to hold the mirror button for a good second for it to work - but I had tried for months to get mine to work, and finally after reading many posts, the above sequence worked on my 2008 Prius with my Lift Master, Security + rolling codes garage opener.

Just - program the button on the mirror with your remote FIRST.. the garage opener will not work.. then use the Learn button on the garage opener and the SAME BUTTON you just programmed.. and it worked great for me. Not programming the mirror button first will not work. Using only the Learn button will not work. You must program the mirror first with the remote, then use the learn button and the SAME button on the mirror. Hope this helps.

Scott 2008 Prius with Lift Master Security + opener.
-

Oct 30, 2009 | 2007 Toyota Prius

1 Answer

I want to delete my programed garage door opener from the home buttons in my tahoe


Press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. Do not hold for longer than 30 seconds

Sep 29, 2009 | 2008 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...