Question about 1990 Ford Bronco

1 Answer

So i want to change the interior from burgondy to tan and i could just hunt down another bronco and remove all the interior which is a pain....or i could pull out all the trim and moldings and paint them that i know i can do but the actual seats and carpet is this possible and if so is it a good idea? or will it be crunchy to sit and look crappy

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,581 Answers

I used a vinyl spray for seats and trim on a boat. I was just spraying a different shade of yellow over the original yellow. It stuck well to the surface but it was sticky forever and attracted dirt and the dirt stuck to it.

If you can get hold of the people the Dealers call to repair Cigarette burns on seats and carpets, they could tell you about different products. I would not recommend the stuff I bought through J.C. Whitney.
Going from light to dark is possible, but I do not think you can go from a dark color to a light one.

I do believe you can get some new carpet through J.C. Whitney. If you need a little work on the seats you can have an Upholstery shop put in a different color insert and two-tone the seats to tie the colors together. When they pull the seats it would be simply for them to change out the carpet.

If the two-tone worked for you, then you may not want to fool with the headliner. I used to handle the new boxed Headliners at Ford. Even with the box, they were a pain.

Good Luck to you, I did not like my experience with the spray products.

Posted on Jul 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I wish to adjust the idle tickover speed a wee bit on a 2007 Ford Transit 2.2 Duratorq engine. It is currenlty ticking over at approx 800 rpm and is hunting at this rev. If I could raise it a wee as I do...


First ensure that the throttle interior is really clean, a surface layer of grime can upset the ECU's ability to meter and govern the air entering the engine. If the throttle body interior is found to be really oily and dirty check on the idle air control valve and make sure that it too is cleaned up. Next put the ignition switch in position 2 (on, but no start) and depress the accelerator fully and release. If there is an issue with the throttle position sensor this procedure can help the ECU relocate the throttle plate position. Start the engine and if it is still hunting locate the air mass meter (AMM) on the air ducting immediately next to the air filter and disconnect the electrical connection. Does this remove the hunting aspect?... the rev speed might change but for the moment concentrate on the evenness of the tick-over. If the idle is even when the AMM is disconnected but hunts when connected then look at replacing your AMM. Try spraying the AMM with no residue electrical cleaning spray to see if this improves matters.

Dec 02, 2010 | Ford Transit Connect Cars & Trucks

1 Answer

No power to fuel pump


check the tan- lt green wire on the fuel relay that is located on the right fender, mine wasn't pushed in all the way, this wire shut down injectors and fuel pump, if you are looking for the shut off switch to reset the relay, it is on the passagers side floor board under the dash, gas two wires, orange and pink, I don't remember the color of the stripes, I removed this switch and wired them together without a problem

Mar 27, 2010 | 1988 Ford Bronco II

1 Answer

1986 FORD BRONCO II - CRANKS BUT NO START - NO SPARK - REPLACED IGNITION MODULE AND HALL EFFECT SENSOR, ALSO TRIED A NEW IGNITION SWITCH. HELP


I just had the same problem, today, check the tan- lt green wire on the fuel relay that is located on the right fender, mine wasn't pushed in all the way, this wire shut down spark and fuel

Mar 01, 2010 | 1986 Ford Bronco II

2 Answers

Is there a relay fuel pump switch for a 1987 ford bronco 2 If we straight wire it to the fuel pump it comes on but when turning on switch fuel pump will not come on.


I just had the same problem, today, check the tan- lt green wire on the fuel relay that is located on the right fender, mine wasn't pushed in all the way, this wire shut down spark and fuel, if you are looking for the shut off switch to reset the relay, it is on the passagers side floor board under the dash, gas two wires, orange and pink, I don't remember the color of the stripes, I removed this switch and wired them together without a problem

Jan 29, 2010 | 1987 Ford Bronco II

1 Answer

Need tans wiring harness for 94 ford bronco


This is not a parts place but I suggest you try your local salvage yard -Craigslist or Ebay. Also some car clubs will exchange parts information.

Best of it

Jan 28, 2010 | 1994 Ford Bronco

2 Answers

Fuel pump not working on 1989 Bronco ii


I just had the same problem, today, check the tan- lt green wire on the fuel relay that is located on the right fender, mine wasn't pushed in all the way, this wire shut down spark and fuel

Jan 16, 2010 | 1989 Ford Bronco II

1 Answer

I need a wiring diagram for a 1988 ford bronco II fuel injectors


I just had the same problem, today, check the tan- lt green wire on the fuel relay that is located on the right fender, mine wasn't pushed in all the way, this wire shut down spark and fuel

Aug 27, 2009 | 1988 Ford Ranger

1 Answer

I just would like to know what to takle first or replace first to tighten up the steering in my 91 ford bronco


to do it you will need a couple specialty tools. You may be able to rent them at the auto parts store. Your going to have to remove the steering wheel and a few other things that can be a pain without the right tools.

Jul 15, 2009 | 1991 Ford Bronco

1 Answer

Dont have a owners manuel so i dont know what the fuse numbers are 93 ford taurus


1996 is all I have. Look on back of cover for fuse chart.

Location
The fuse junction panel is located to the left of the steering column. To expose the fuse junction panel, remove the fuse panel cover (14A003) as outlined.
db0a7af.gif

Fuse Loc. Number Fuse Amp Rating Fuse Color Circuit Protected 1 — — Not Used 2 5A Tan Instrument Illumination 3 10A Red Left Low Beam Headlamp 4 10A Red Right Low Beam Headlamp 5 5A Tan Brake/Shift Interlock Rear Window Defrost 6 15A Lt Blue Back-Up Lamps/Air Conditioning, Speed Control, TR Sensor 7 10A Red Starter Relay Power, TR Sensor 8 5A Tan Radio Mute, Power Antenna, GEM Module 9 10A Red Anti-Lock Brake System, Central Temperature Monitor 10 20A Yellow Electronic Engine Control (EEC) Relay, Ignition Coil, PATS, Radio 11 5A Tan Air Bags, Alternator Indicator Lamp 12 5A Tan Gauges, Warning Lamps, Transmission Control Switch, GEM Module, Integrated Control Panel Autolamps 13 5A Tan Air Bags, Blower Motor, Electronic Automatic Temperature Control 14 5A Tan Light-Out Module 15 10A Red Multi-Function Switch (Turn Signals) 16 — — Not Used 17 30A Lt Green Front Windshield Wipers/Washers 18 5A Tan Headlamp Switch Illumination 19 15A Lt Blue Rear Window Wiper/Washer 20 5A Tan Radio Memory, Phone, Remote Anti-Theft Personality (RAP) Module, Integrated Control Panel (ICP) 21 20A Yellow Cigar Lighter 22 5A Tan Power Rearview Mirrors, Antenna, Decklid Lamps, Autolamp 23 5A Tan Generic Electronic Module (GEM) Power, Remote Anti-Theft Personality (RAP) Module, Passive Anti-Theft System (PATS) Module 24 5A Tan Integrated Control Panel, Radio, Speedometer 25 10A Red Diagnostics (Data Link Connector) (DLC) 26 15A Lt Blue Decklid Release 27 10A Red Battery Saver System 28 15A Lt Blue Stoplamps, Speed Control 29 15A Lt Blue Multi-Function Switch (Hazard Lamps) 30 15A Lt Blue Highbeam Headlamps, Daytime Running Lamps (DRL), Instrument Cluster 31 5A Tan Tail Lamps 32 5A Tan Heated O/S Rear View Mirrors, Integrated Control Panel (ICP) 33 5A Tan Power Window and Lock Switch Illumination 34 — — Battery Saver Relay 35 — — Driver Unlock Relay 36 — — Rear Defrost Relay 37 — — Interior Lamp Relay 38 — — Driver Power Window Relay (One Touch Down) 39 — — Accessory Delay Relay

Apr 09, 2009 | 1993 Ford Taurus

4 Answers

Back door wont open and window wont go down


The rear window has to be completely down in order to move the tailgate! You should be happy that your window is stuck up, unlike mine which is stuck all the way down! I have to completly take apart my tailgate!! If you want to try a trick to get the rear window down, my bronco has a rear window switch right next to the headlight knob, take the 2 purple wires on that window switch, and cross them, if your motor still works and if the wires are good, that should make the window go down!!! good luck, hope that helps!

Oct 05, 2008 | 1995 Ford Bronco

Not finding what you are looking for?
1990 Ford Bronco Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...