Question about 1984 Toyota Corolla

Open Question

What are the valve clearance thickness of the intake and exhaust valve of a 1984 toyota corona 12r engine

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: VALVE CLEARANCE

I USE 0.04MM IN INTAKE AND 0.08MM IN EXHAUST VALVE

Posted on Apr 15, 2009

michigan man
  • 3533 Answers

SOURCE: valve clearance of 12 valve engine

i do not know but give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Feb 08, 2010

  • 1 Answer

SOURCE: what are the tappet clearance settings for the

any 1 know the tapit setting for a toyota starlet 1990

Posted on Feb 17, 2010

  • 1 Answer

SOURCE: what is the valve clearance

Intake : 0.20mm ( 0.008 in.) Exhaust : 0.30mm ( 0.012 in.)

Posted on Jan 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

2 Answers

Hi Ace 2L diesel van. What is the valve clearance warm and cold?


Cold: Intake 0.30mm, Exhaust 0.50mm.
Hot: Intake 0.20mm, Exhaust 0.040mm.

The 2L Toyota engine runs an overhead cam with bucket lifters, and requires removing and replacing of shims to adjust clearances...

Feb 13, 2016 | Toyota Cars & Trucks

2 Answers

I'm looking for the Toyota corrola 1.6 4AF engine valve clearance


will need a micrometer, valve clearance adjustment tool set for shimmed lifters,small magnetic arm, appropriate shim selecting charts (manufacturer will have this if you can get the nec. measurements).
Measure thickness of shims removed (using micrometer) and use this formula where T=Thickness of old shim; A=Valve clearance measured; N=Thickness of new shim required.
Intake valves: N = T + (A - 0.02 mm (0.008 in.)) Exh. valves: N = T + (A - 0.25 mm (0.010 in.))
Then you need to find shims as close as possible to the calculated values.
Valve clearances (cold) are as follows: Intake0.15 - 0.25 mm (0.006 - 0.010 in.) Exhaust0.20 - 0.30 mm (0.008 - 0.012 in.)
Note, if you are not familiar with precision measuring using a micrometer, this may be better left to a trained tech. These are high revving little power plants and you don't want a problem at 8K rpm.

Jul 14, 2015 | Toyota Cars & Trucks

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

1 Answer

I need to know the fireing order on a 2.8l engine in a 1985 ford ranger


Tune Up

Spark Plug

AWSF-42C

Spark Plug Gap

0.044

Ignition Timing

10 degrees BTDC

Firing Order

1-4-2-5-3-6

Distributor Rotation

Clockwise

Valve Clearance Intake

0.014

Valve Clearance Exhaust

0.016

Aug 04, 2011 | 1984 Ford Ranger

2 Answers

What are the valve clearance specs for a 1996 Toyota T100 v6?


you should get haynes auto repair manul for your particular car that way you will have the correct information about that. you can get the manul at autozone or any autopart, all you need is your car info, to pick the right manual for your car, good luck

Jul 15, 2011 | Toyota T100 Cars & Trucks

3 Answers

Valve clearance 4hj1 isuzu engine


This is the specs for the 4H Diesel engine:
Intake valves clearance cold 0.4mm(.016inches)
Exhaust valve clearance cold 0.4mm(.016inches)

Jan 28, 2011 | 1995 Isuzu Pickup

2 Answers

What is the valve clearance of toyota 12r ?


Intake : 0.20mm ( 0.008 in.) Exhaust : 0.30mm ( 0.012 in.)

Jan 15, 2011 | 1983 Toyota Corolla Deluxe

2 Answers

What is the valve clearance in the 1993,1500cc


there is a white sticker underneath on the bottom side of your hood that should give you valve clearance specs.

Nov 14, 2009 | 1993 Toyota Tercel

1 Answer

Need to know how to adjust valves, or a print-out of adjustment procedure and tools reguired. 1989 toyota gt-s corolla 1600 16 valve 4a-ge cal engine


This engine utilizes shims to set proper clearances, you will need a micrometer, valve clearance adjustment tool set for shimmed lifters,small magnetic arm, appropriate shim selecting charts (manufacturer will have this if you can get the nec. measurements).
Measure thickness of shims removed (using micrometer) and use this formula where T=Thickness of old shim; A=Valve clearance measured; N=Thickness of new shim required.
Intake valves:   N = T + (A - 0.02 mm (0.008 in.)) Exh. valves:     N = T + (A - 0.25 mm (0.010 in.))
Then you need to find shims as close as possible to the calculated values.
Valve clearances (cold) are as follows: Intake 0.15 - 0.25 mm (0.006 - 0.010 in.) Exhaust 0.20 - 0.30 mm (0.008 - 0.012 in.)
Note, if you are not familiar with precision measuring using a micrometer, this may be better left to a trained tech. These are high revving little power plants and you don't want a problem at 8K rpm.

Jun 05, 2009 | 1989 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...