Question about 2007 Chrysler Sebring Sedan

1 Answer

Car will not crank battery is good hear clicking sound around gear shifter could it be neutral safety switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Your problem is the starter motor. Usually the bendix unit or so call solenoid or your starter has bad bearings.

Posted on Jul 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 tahoe wont crank wont start with new battery


Does starter click? Try turning on headlamps and get someone to watch as you try to start car. If headlamps dim, likely bad starter or battery cable(s). If they don't dim, bad solenoid, starter switch, neutral safety switch. Try starting in neutral and jiggle shifter while trying. If it starts, replace neutral safety switch.

Dec 01, 2014 | 1999 Chevrolet Tahoe

1 Answer

Ok, engine won't crank , I can hear all relays clicking but no cranking of the engine, usualy after 10-20 atempts it starts but latetly it is getting more dificult,allso I noticed that the shift position...


Try starting the car in neutral. Keep your foot on the brake and put on the emergency brake and try to start it in neutral instead of in park. The vehicle is equipped with a neutral safety switch which does not allow you to start the car in reverse or any of the drive gears. You can only start the car in park or neutral. You may have a problem with the shifter or the shifter cable. On some vehicles the shifter cable can be adjusted.

If you have any other questions feel free to ask

Jan 21, 2011 | 2000 Mazda MPV

1 Answer

Vehicle will not crank but all items(headlights,rear lights,interior lighs,radio,windows) are working fine. Alternator,starter and battery have all been checked but still wont crank. No clicking or...


Check and see if the shift indicator is showing that it is in a drive position when the shifter is in park.This will cause the vehicle to not start because the computer thinks it is in gear and not allow power to the starter.The problem is the ignition switch.Also check the neutral safety switch on the side to the transmission.This is a 12 pin connector.The number 11 pin is power to the safety switch,12 is crank voltage,and 1 is starter relay coil supply voltage.Hope this helps.Good luck.

Dec 28, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Describe your 2002 Chrysler Town &


Safety neutral switch o.k.? Tried moving shifter through all gears while holding key in start position?

Aug 03, 2009 | 2002 Chrysler Town & Country

1 Answer

New starter.new battery.all electrical works lights,gauges,radio,wipers etc but van wont start.no cranking sound just slight click uinder washer reservoir behind battery


there is not just one thing that can cause this problem. it could be in the ignition switch, it could be the wiring from switch to starter relay, could be the neutral safety switch. i can tell you a quick and dirty way to test this, have to be careful if you do it. put the vehicle in park, make sure it's in park, otherwise it will roll when you do this and you could get run over by your own vehicle. now you will need a set of jumper cables. make sure you can get to the hot side terminal of starter, one jumper cable contact has to go there. the other side has to go to hot (positive) side of battery. if when you tap the jumper cable to the hot side of starter the starter cranks just like it should then you have a wiring problem. if that's the result you get try jiggling the gear selector around and cranking ignition, or try starting it in neutral. if that makes a difference, if it cranks in neutral or if you move gear selector around when it's in park, then you probably have a bad neutral safety switch. if that doesn't make a difference but you are able to get it to crank by jumping straight from battery to starter then you have a wiring problem in ignition system. hope that helps

Jun 16, 2009 | 1993 Pontiac Trans Sport

3 Answers

Car wont go in gear


you have a problem with posibly witht he adjustment on you neutral switch. the transmission has this to prevent starting in gear. it obviosly works fine in newtral so it needs to be adjusted or the lever on your transmission needs adjust ment to allow this sensor to do its job
i hope this helps

May 06, 2009 | 1994 Lincoln Town Car

Not finding what you are looking for?
2007 Chrysler Sebring Sedan Logo

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...