Question about 2007 Ford Escape Hybrid FWD

Open Question

Ford escape flywheel torque settings

Ford escape 2007 flywheel/ringgear bolt torque settings

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

chuck943
  • 783 Answers

SOURCE: torque specs foe 4.9 ford f150 flywheel

75-85 ft lbs

Posted on Mar 04, 2009

chuck943
  • 783 Answers

SOURCE: torque settings

Torque Specifications Description Nm lb-ft Brake caliper retaining bolts 28 21 Brake hose to brake caliper union 15 11 Brake caliper anchor plate retaining bolts — 2.0L Duratec ST 133 98

Posted on Mar 15, 2009

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

mindreader
  • 578 Answers

SOURCE: i need the torque specs for a ford 300 inline 6

Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

What are the torque specs for the flywheel bolts?


Flywheel bolts are usually torqued up to 60ft lbs.
Use some threadlock, too

Nov 02, 2015 | Ford Cars & Trucks

1 Answer

Torque wrench setting for 2007 ford escape camshaft caps


40 to 45 INCH pounds. Not foot pounds. 40 foot pounds will strip the threads out of the head.

Mar 01, 2015 | 2007 Ford Escape

1 Answer

2007 ford escape 2.3 what the center piece bolted in the center crankshaft called


i believe its called a main bearing cap assembly. i could be wrong but if i ramember corectly its all in one pieace on the focan made of aluminium it is retained by steal dowles to make sure of position use a deadblow hammer to not damage the serfaces to install put new berings in assebley get the torque specs torqu it down make sure you got the right torque sequence so it gos on evenly

Jul 22, 2012 | 2007 Ford Escape

1 Answer

Where is the crank position sensor located on the 2002 Ford Escape? Will I need a rubber O ring or paper spacer?


The Crankshaft Position Sensor (CKP):
4 CYL - located on the front of the engine, near the flywheel end of the block. remove exhaust manifold, disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket req'd. torque to 62 inch-pounds
6 CYL - located next to crankshaft pulley - remove right wheel, remove lower right splashshield. disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket req'd. torque to 89 inch-pounds

Dec 17, 2010 | 2002 Ford Escape

2 Answers

2004 ford escape exhaust manifold torque specs?


2b507d0.jpg

Fig. Left side exhaust manifold bolt torque sequence-3.0L engine


22ac5ae.jpg

Fig. Right side exhaust manifold bolt torque sequence-3.0L engine

Both cases, exhaust manifold and new gasket, torque the bolts to 15 ft. lbs. (20 Nm).

Good luck (remember to rate this answer).

Oct 22, 2010 | 2004 Ford Escape

1 Answer

Flywheel torque setting vw transporter t30


VW Transporter 2.5 TDI-PD, (made year: 2003 ... 2007), engine code: AXD, 130 HP / 3500 rpm.
Important note: use new bolts!
Flywheel/driveplate torque setting: 60 Nm + 90 degrees.
Clutch to flywheel torque setting: 22 Nm.

May 21, 2010 | 2004 Volkswagen Eurovan

1 Answer

How many bolts connect the flywheel to the torque converter?


6 bolts connect the flywheel to the crankshaft
If it has an automatic transmission the flexplate or flywheel has 6 bolts to connect it to the crankshaft and 4 more bolts to connect to the torque connverter

Jul 25, 2009 | 1984 Ford Bronco II

2 Answers

Flywheel bolts torque settings


Check with your local auto parts store. Or buy a repair manual

Jun 07, 2008 | 1999 Volkswagen Golf

Not finding what you are looking for?
2007 Ford Escape Hybrid FWD Logo

Related Topics:

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...