Question about 2000 Chrysler Concorde

1 Answer

How to replace hardware on front brakes - 2000 Chrysler Concorde

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

All the front brake hardware is, is anti squeaker clips, very simple, if you pick up the parts from a parts house it may have instructions. otherwise its just after removing the calipers and the pads, on the caliper mounting bracket the clips should be there just pull them off and put some HI temp. caliper grease on them just a nice thin layer and put it back together and your good to go

Posted on Jun 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My car chirps while increasing speed and when I brake my vehicle.


It is possible that the broken tab is your problem because the tabs keep the hardware from moving, especially when you apply the brakes. To determine if this is the case, remove the tire,brake caliper, brake pads, and hardware. Put one of the lug nuts(or two if needed) back on to hold the rotor in place. Spin the rotor by hand and listen for that chirping sound. If you don't hear it, the hardware is the problem. If you can still hear it, check that metal plate that protects the back side of the rotor to make sure its not bent and rubbing against rotor. Also check that nothing is rubbing on the trans-axle(if its front-wheel drive). If all is well in these two places, the only thing left that spins in that area is the wheel bearing. They usually make more of a grinding or roaring sound but sounds can be tricky.. I am a mechanic for a car rental company and often have to diagnose problems by the sound they make. I hope this info is helpful.

Jan 17, 2016 | 2003 Buick LeSabre

1 Answer

Adjust parking cable 99 dodge dakota -drum brakes


Unless you have replaced the cable, it should never need to be adjusted. If you can reach under the vehicle, and when wiggling the parking brake cable, if it is taut (not sagging), then it is probably adjusted properly. What usually causes the parking brake cable to appear mis-adjusted (the parking brake won't hold the vehicle), is that the self-adjusters in the rear drum brakes are not working properly. This is bad because it means that you are not getting proper braking from the rear brakes as well as having the parking brake issue. This can cause premature wear to the front disc brake pads/rotors and affect braking power and control under certain stopping conditions. Front disc brakes work so well that many people never realize that their rear brakes aren't doing their fair share. The purpose of the self-adjusters in the drum brakes is to keep the rear brake shoes at a consistent distance from the drum's inner surface as the shoe lining wears down. If the adjuster works correctly, the parking brake will always stay in adjustment. You CAN adjust the parking brake cable, but if the problem is actually with the self-adjuster, you are masking the real problem, and later on when you need to replace the rear brake shoes, you will find it impossible to put the drum back on over the shoes as the parking brake will have the shoes pushed out too far. Have a mechanic check out the self-adjuster mechanism. It is always a good idea whenever you replace the rear brake shoes to replace all the rear brake hardware as well. You don't replace rear brakes nearly as often as the front ones, and the cost of the hardware is minimal in relation to the satisfaction of knowing that non-corroded parts will work better and provide longer service than the older, gummed-up and rusted hardware that is currently installed.

Sep 11, 2014 | Dodge Dakota Cars & Trucks

2 Answers

My brake pads have been changed and the wheels continue to squeal. They rattle and squeak when driving and braking


it just sounds like a poor quality job...the proper way to do a brake job is a high quality set of front pads such as a bendix or raybestes gold line pads,, then have the front brake rotors machined an a amco brake lathe or even better a on the car brake lathe. make sure all brake caliper hardware is properly cleaned an lubercated or replaced with new hardware....then have the rear brakes adjusted( adjust only if ur car has rear drum brakes...rear disc brakes r selfadjusting

Jul 16, 2011 | 2003 Chevrolet Impala

1 Answer

Front brake pads rattle on a 2001 GMC Sierra 1500HD


Is it new hardware?....older pre used hardware should be replaced....also, check the dust shields behind the rotors....could be rusted loose....happened to mine

Feb 15, 2010 | 2001 GMC Sierra 1500HD

1 Answer

How to replace my front nissan alitma brakes


remove tire, two bolts 14mm i believe 1 on top 1on bottom use c clamp tp compress pads remove lower slide bolt calipers will slide up check hardware grease shims contact points push caliper down install lower bolt pump brakes several times and go where do u live ill do it

Sep 30, 2009 | 2003 Nissan Altima

1 Answer

I have rattling on my front brakes of my 1998 v70 but


Hello you have what is called a brake pad walking. How to fix this is to replace the brake pad hardware so that the brake pads will be more secure .It should not be a safety issue but i know its annoying .

Jun 28, 2009 | 1999 Volvo V70

1 Answer

All of the front brake harware does not fit


Send me $9.99 & I will tell you how i did it.

Jun 13, 2009 | 2000 Lincoln LS

1 Answer

Brakes are sticking after application front right being the worse


Hi,


I've had a similar problem as what you describe. For me it was as simple as replacing a faulty front brake line. Never had any problems since. Hope this will help you narrow it down some.

Mar 31, 2009 | 1989 Honda Prelude

Not finding what you are looking for?
2000 Chrysler Concorde Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...