Question about 1998 Chevrolet Blazer

1 Answer

How to change dooe lock relay

How to change door lock relay

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,513 Answers

Hi,

Thanks for writing to Fixya.com.

The power door lock relay is located in the dash behind the headlight switch assembly. The power door lock relay was shorted to ground and was completely inoperative. Take a look at the very end of the dash, what is parallel with the side of the truck. You can only see this portion of the dash with the door open. There will be a small cover that you can remove.


Thanks for contacting Fixya and please accept the solution if it has helped you.

Posted on Jun 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door lock dont always work


What door lock doesn't always work ? One or all of them . This is a complex set up for these door locks ! The switch is an input to the BCM - body control module . There is logic involved in the microprocessor , there are relays built in to the BCM ! Could have a DTC - diagnostic trouble code stored in the BCM ! Could be a bad connection at the BCM or master window switch ! A bad ground !
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
DOOR LKS fuse


?€¢
Driver door lock actuator


?€¢
Driver door lock switch


?€¢
GMLAN serial data link


?€¢
Keyless entry transmitter


?€¢
Passenger door lock actuator


?€¢
Passenger door lock switch


?€¢
Remote control door lock receiver (RCDLR)


The DR LCK fuse supplies battery voltage to the body control module (BCM) for the power door lock system. The BCM supplies and monitors a reference voltage to the driver and passenger door lock switches through the door lock switch lock/unlock signal circuit. Each door lock switch receives ground at G300 which is also the ground for the door lock and unlock relays located in the BCM. When a door lock switch is placed in the lock position, the reference voltage is switched to ground and the BCM senses 0.0 volts on the door lock/unlock signal circuit. When a door lock switch is placed in the unlock position, the reference voltage is switched to ground through a 1.5k ohm resistor that is internal to each of the door lock switches and the BCM senses approximately 2.9 volts on the door lock/unlock signal circuit. The BCM interprets what position the activated door lock switch was placed in based on the voltage drop.
The BCM, upon receipt of a lock or unlock switch signal, will switch the appropriate door lock/unlock relay coil control circuit to ground causing the appropriate door lock/unlock relay to energize. With the relay energized, voltage is applied to the door lock actuator control circuit causing the door to either lock, or unlock depending on what command was received from the power door lock switch or remote control door lock receiver (RCDLR). When a power door lock/unlock relay is not energized, the switch contacts are normally grounded through the BCM which provides ground to the appropriate door lock actuator for the lock/unlock function being performed. The power door lock/unlock functions are performed by reversing the flow of voltage through the door lock actuator control circuits. The BCM has three internal drivers for the power door lock system. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked separately from the passenger door. For additional information concerning keyless entry, refer to Keyless Entry System Description and Operation.
This is one you may want to take to dealer or some other ASE certified repair shop ! To do this right you need a Tech 2 scan tool !
Ignition ON, observe the scan tool Door Lock Switch parameter while using the driver and passenger door lock switches. The parameter should change from Idle to Lock and Unlock.
?‡'
If the value does not change, refer to Door Lock Switch Malfunction.

Command the doors to LOCK and UNLOCK with the scan tool, the door lock actuators should LOCK and UNLOCK when changing between the commanded states.
?‡'
If one or more doors do not LOCK or UNLOCK, refer to Door Lock Malfunction.

Aug 12, 2015 | 2009 Pontiac Solstice Convertible

1 Answer

Dear Sir, I have a double cab pick up 2.8TDI, the central lockink works independant. On press the driver door unlocks, second press the other doors unlock. Locking is in normal, on press all doors lock....


there is a central locking switch in the drivers door lock over time it will get mucky and or warn from use and weather. its built into the lock but you can clean it out by taking off the door card and spraying some cleaner in like wd40 or deep penetrating oil into the switch.

Mar 06, 2014 | Mitsubishi Cars & Trucks

1 Answer

Volkswagon caddy sliding door


Ok this problem is easy u have to take off the door panelling and look and the power door lock the piece that locks and unlock's the door sometime's fail's it is eather not working or stuck. to check where on the dooe where it can stick is where it latches when u close the door spray the linkage with WD40 to loosen it up Hope this Help's U...

Jun 25, 2013 | Cars & Trucks

2 Answers

My 2003 yaris will not lock the passenger side door when useing the key in the drivers dooe


Hi Gary,

Please check the power line / switch on passenger side. The switch may rusted or has loose connection.

regards, Jay

Sep 23, 2012 | Cars & Trucks

2 Answers

2004 toyota sienna manual sliding door problem. When opened all doors will lock shortly after. On same door, interior light will not come on when sliding dooe opened


I have the same problem. I thought it was an electrical problem. My interior lights would go one and off and I would hear clicking noises. I took it to a mechanic and he said my switches for the sliding doors are bad so he had to order them from toyota and I'm getting them replaced tomorrow. Take it to a mechanic and get the switches replaced.

Jan 18, 2011 | Toyota Sienna Cars & Trucks

1 Answer

Driver dooe is hard to open unless I pull very hard on the handle, any suggestions?


Sounds like your door locks can use a little lube. Give that a try and see if it helps out at all.

Dec 14, 2010 | 1999 GMC Suburban

1 Answer

I have doors that will not open properly on my 98 explorer


If the handles are working and the rods are connected properly then more likely the problem is the door latch.

Dec 21, 2009 | 1998 Ford Explorer

1 Answer

I have a 2006 Jeep liberty and my key clicker does not work on the drivers door but does on all the others. The power lock and unlock button inside works on all but drivers dooe whats wrong and how do i...


Failure of the Lock energiser. Take the Door trim Off, diconnect the Electric connector, Using a remote power supply connect that ,using the correct polarity, Pos to Pos....Neg to Neg, if you get no response, there is the problem.

Regards.DT

Aug 26, 2009 | 2006 Jeep Liberty

1 Answer

How to change door lock cylinder on 05 jette


remove dooe panel..disconnect the rods which are clipped into the barrel, then there is a "U" shaped clip against the door,holding the barrel in place, it has a flat lip on it ,to make extraction easy...then door barrel will push through the hole

Aug 01, 2009 | 2005 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

343 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...