Question about 2005 Nissan Altima

3 Answers

My 2005 altima idles high and engine code

My 2005 altima idles high and engine code p0507.Recently had the throttle body cleaned.What can i do to fix this problem

Posted by on

  • Anonymous Apr 01, 2014

    I disconnected battery on altima 2005 now the idle goes up and down

  • Anonymous Apr 01, 2014

    I replaced starter on 2005 altima now my idle goes up and down

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set.

Posted on Jun 07, 2010

  • koltonserwe Jun 07, 2010

    Most likely you'll notice the idle speed is higher than normal. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.


  • koltonserwe Jun 07, 2010


    CausesA P0507 DTC trouble code may be caused by one or more of the following:


    • A vacuum leak

    • Leaking air intake after the throttle body

    • EGR valve leaking vacuum

    • A faulty positive crankcase ventilation (PCV) valve

    • Damaged/failed/dirty throttle body

    • Failed EVAP system

    • Failed IAC (idle air controller) or faulty IAC circuit

    Possible SolutionsThis DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns.
    If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedures



×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

Your Altima will require an idle air volume learn after cleaning. This procedure will set your idle speed. If the code keeps recurring after the IAVL your throttle chamber may need to be replaced.

Posted on Jun 24, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

2004 altma replaced new gaskets on bottom and top intake also replaced throttlebody had it put on a snap on scanner still problem with high rpm and surges up and down.went through relearing still same problem

Posted on May 24, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to fix a dtc p0507?


A vacuum leak Leaking air intake after the throttle body EGR valve leaking vacuum A faulty positive crankcase ventilation (PCV) valve Damaged/failed/dirty throttle body Failed EVAP system Failed IAC (idle air controller) or faulty IAC circuit

Sep 28, 2015 | 2005 Nissan Altima

1 Answer

Code p0507 Hyundai Santa fe cost to repair


Jena: According to http://www.obd-codes.com/p0507: " P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set.
Potential Symptoms Most likely you'll notice the idle speed is higher than normal. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
Causes A P0507 DTC trouble code may be caused by one or more of the following:
  • A vacuum leak
  • Leaking air intake after the throttle body
  • EGR valve leaking vacuum
  • A faulty positive crankcase ventilation (PCV) valve
  • Damaged/failed/dirty throttle body
  • Failed EVAP system
  • Failed IAC (idle air controller) or faulty IAC circuit
Possible Solutions This DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns.
If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedures."
So, Jena, you start with the cheapest possible solutions. Go to YouTube and look up how to detect a vacuum leak. https://www.youtube.com/watch?v=9CPqbaSgcok Buy a can of throttle body cleaner and get one of the auto store people to show you how to get to the throttle body (basically you use a screwdriver and take off the huge air hose). Then clean the throttle body. If you don't get rid of the problem, watch the YouTube video on how to clean the EGR Valve. https://www.youtube.com/watch?v=TB1E9opb87Y While you are at the auto parts store, you will probably want to buy an PCV valve. This may solve your problem even without a mechanic! :)
=====So

Apr 17, 2015 | Hyundai Santa Fe Cars & Trucks

1 Answer

Correct code P0504?


What Colorado do you have ? 2 wheel or 4 wheel drive ? Sport ,sport LS 3.5L , Z71, Z71 LS. etc. what size engine ? an does it have electronic throttle control ? I have factory service info an it is not showing that code .
DTC P0506

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:
DTC P0506 Idle Speed Low
DTC P0507

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:
DTC P0507 Idle Speed High
Cleaning the throttle body mite take care of it !
Cleaning Cleaning An Electronic Throttle Body Safely

Jan 31, 2015 | 2005 Chevrolet Colorado

1 Answer

Hy is there a code p0507? and how do i fix?


This P0507 code is one that's sometimes triggered on vehicles that have electronic throttle control. That is, they don't have a regular throttle cable from the accelerator pedal to the engine. They rely on sensors and electronics to control the throttle. In this case, the P0507 DTC (diagnostic trouble code) is triggered when the PCM (powertrain control module) detects an engine idle speed that is greater than the desired (pre-programmed) RPM. In the case of GM vehicles (and possibly others) if the idle speed is over 200 rpm higher than expected, this code will be set. A P0507 DTC trouble code may be caused by one or more of the following: A vacuum leak Leaking air intake after the throttle body EGR valve leaking vacuum A faulty positive crankcase ventilation (PCV) valve Damaged/failed/dirty throttle body Failed EVAP system Failed IAC (idle air controller) or faulty IAC circuit. This DTC is more of an informational code, so if there are any other codes set, diagnose them first. If there are no other codes, inspect the intake air system for air or vacuum leaks and damage. If there are no symptoms other than the DTC itself, just clear the code and see whether it returns. If you have an advanced scan tool that can interact with the car, command the idle higher and lower to see if the engine responds appropriately. Also check the PCV valve to see if it's blocked and needs to be replaced. Check the IAC (idle air controller) if equipped, verify it's operation. If available, try swapping in a new throttle body to see if that fixes the problem. On Nissan Altimas and possibly other vehicles the problem may be fixed by having the dealer perform an idle air relearn procedure, or other relearn procedure


Jul 27, 2014 | 1999 Daewoo Leganza

2 Answers

Code p0507


possible causes are:

Dirty throttle body
Electric throttle control actuator incorrectly adjusted/faulty/damaged
Air leak on Intake
Poor electrical connection to the Intake Air Control valve

P0507 KIA Idle Air Control IAC System RPM Higher Than Expected

May 14, 2014 | 2003 Kia Sedona

1 Answer

Car sometimes jerks when idle and wont accelerate when this happens


crank sensors fail on these very frequently,causing running issues. if service engine soon light is on, then your mechanic should be able to pull something from computer. sounds to me like he doesn't know what he is doing. get your self a new mechanic. that light doesn't come on just for fun. it comes on to tell you that there is a problem. if a throttle body is an issue, he should have pulled P0507 ICS system. If so, there may be an issue with the throttle body. have seen few with computer issue causing throttle body code, but those are rare. most likely throttle body, but depend on code number.

Jun 29, 2013 | 2005 Nissan Altima

1 Answer

I have a 2005 Nissan quest and I'm getting a p0507


No..you can't adjust the idle...

Possible cause---Electric throttle control actuator, intake air leak or PVC system...check these 3 things...

Jun 04, 2011 | 2005 Nissan Quest

2 Answers

My monte carlo has code p0507 what is it and how can i fix it


possible causes
- Dirty throttle body
- Electric throttle control actuator misadjusted or damaged
- Faulty Electric throttle control actuator
- Intake air leak
- Poor electrical connection to the Intake Air Control (IAC) valve
solution !!!
If there are no intake leaks, clean throttle body, adjust engine idle and erase engine code. If the code comes back you may have to replaced the Electric Throttle Control Actuator (Motor) to repair the problem.

Jan 28, 2011 | 2000 Chevrolet Monte Carlo

3 Answers

My nissan is showing this code p0507. What is that mean.


idle controll system idle to high is the code description

Jun 09, 2010 | 2003 Nissan Maxima

Not finding what you are looking for?
2005 Nissan Altima Logo

2,834 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...