Question about 1997 GMC Jimmy

1 Answer

How do I get base timing on 1997 GMC 5.0L - 1997 GMC Jimmy

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 143 Answers

Scan tool in diagnostic mode will work if not bridge the black and the white with black strip terms together at the diagnosic connnecter should run 8-10 dgrys advanced

Posted on Jun 07, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you install the antenna base on a gmc envoy

Unscrew the antenna first. Look at the base, no lock screw? it pops off. Under it is a nut to remove. this releases the base. Now it the tricky part. The base has to be pulled out. Most times it is threw the door jam. sometimes your have to remove the inner fender cover. Follow it to the body, then inside the body. Pull it threw. Most times they disconnect close to the body. Some times they disconnect at the radio. I've done to many to let you know for your model. But I can say it is one or the other.

Aug 11, 2015 | GMC Cars & Trucks

1 Answer

How to set the timing on a 1997 gmc 1500 5.7


1997 GMC Truck C1500 1/2 ton P/U 2WD 5.7L SFI 8cyl

The Ignition Timing


Oct 15, 2014 | GMC C1500 Cars & Trucks

1 Answer

Diagram for firing order and where they go on the distributor for 1997 gmc jimmy

Hi there:1997 GMC S15/T15 Jimmy 4.3 liter V-6 VIN "W"

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 01, 2012 | GMC Jimmy Cars & Trucks

1 Answer

Where is the horn relay found on a 1997 GMC Sonoma? The horn is not working and I need to check the relay.

put your head down by the column tap the horn do you here clicking .ifnot did you check fuse . sum times people un plug the horn because it gos of to ease from elarm horn is in the grill.

Jan 27, 2010 | 1997 GMC Sonoma

1 Answer


A blink need dual element bulb.

Check and see did some one jam a single dot/single element bulb into the socket.

Please look at the base socket first. If it has two contacts then you will need a bulb with two contact on the base.

Dec 08, 2009 | 1997 GMC Sierra

1 Answer

My timing is off where do i reset it at to a 1997 gmc savana 1500

Timing is set by loosening the bracket that holds the distributor. It is located at the base of the distributor where it enters the engine block. Loosen it a small amount then you can turned the distributor left or right to advance or ****** the timing. They make custom distributor wrenches that are curved so you can get to the bolt head easier. Some have a square hole in the shaft so you can put the wrench on a ratchet.

Dec 04, 2009 | 1999 GMC Savana

2 Answers

OK 1997 gmc sierra 5.7liter 4x4 replaced coil and

Doesnt this engine use a crank position sensor? mounted on timing chain cover.I would check that first

Oct 17, 2009 | 1997 GMC Sierra

1 Answer

Key wont come out of 1997 GMC Jimmy ignition

Go to auto wreckers and replace the console shifter unit (stick, base, and all components) there is a small solenoid on the side of the stick at the base which is malfunctioning thankfully it's made by chevy so there is no dealer cure under several hundred dollars. I went to an auto wrecker got the whole unit for $50 bucks (price will vary depending on area and wrecker) 6 bolts later and a couple clips and i had fixed it, 8 months later still no problems.

Mar 18, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides