Question about 1997 Honda Civic

1 Answer

Makes weird loud noise when depressing the clutch. Replaced the throw out barring and the transmission and still makes the same noise.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 143 Answers

Did you replace or lube the spigot bush or replace the bearing when you had it out if not start there

Posted on Jun 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced clutch master cylinder work find, but grinding nosie bottom inside clutch


I don't fully understand your question but if the clutch is working and just makes a grinding noise when you depress the clutch pedal, it is probably a bad throw-out bearing.

May 28, 2014 | 1996 Chevrolet K1500

1 Answer

On2nd clutch 08 wrangler 1st one replaced @ 9000 mi.s throw out bearing makes noise again


I hope when the first clutch was replaced the throw out bearing was replaced. It sounds like you are either riding the clutch (foot resting on clutch pedal and partially depressing the clutch during normal driving) or the adjustment is incorrect. The throwout bearing should not contact the pressure plate unless the clutch pedal is depressed when adjusted correctly. The constant contact is what wears the bearing out prematurely.

Dec 31, 2010 | 2008 Jeep Wrangler

1 Answer

I have a manual transmission in my '04 Mustang. When I begin to depress the clutch, an odd grinding sound starts, not loud but enough to warrant concern. As I drive, the car sounds fine. Switching gears...


Worn throw out bearing, replace or the problem may damage other components. This requires dropping the entire transmission. this bearing sits between the clutch pressure plate and clutch slave assembly. When the clutch pedal is pressed, the bearing makes contact with the spinning clutch pressure plate. If defective, grinding/squealing noises may be heard. If the bearing fully fails, loose debris may damage other components. Replace immediately!!

Dec 11, 2010 | 2004 Ford Mustang

1 Answer

Mazda rx8 grind from transmission tunnel


That's the "throw out" or "release bearing". If it makes a loud noise you'll have to take it to a shop as the transmission has to be pulled to replace it.
The clutch, pressure plate and release bearing are usually all replaced at one time....

Aug 14, 2009 | 2005 Mazda RX-8

1 Answer

Loud clanking noise in or outof gear if the clutch is not engaged


Sounds like a throw out bearing or pressure plate problem. Run it by a trany shop, and they should be able to tell quick and easily if that's the problem.

Jun 08, 2009 | 2006 Kia Rio5

1 Answer

Clutch/transmission problem


When the car is sitting idling,and the clutch is not depressed,it makes a grinding noise because the input shaft of the transmission is being forced to turn by the clutch,which is engaged,and even though the trans is in neutral,the input shaft is still turning,and this is called "neutral roll over" noise,and some of the assemblies inside the trans are freewheeling around.The noise goes away when the clutch pedal is being depressed down,because the input shaft of the transmission is no longer turning.So it does sound like an internal transmission problem.It is still possible for the throwout bearing to be bad,and it can be checked when the trans is removed from the vehicle,Remove the throwout bearing from the trans input sleeve,and press down on the bearing flange and turn it at the same time.It should feel smooth and free.If it catches or feels gravelly,then the bearing is bad and that could be your noise.Also,turn the input shaft of the trans and same thing,if it's smooth and free or if gravelly feeling......Good luck.

Jul 18, 2008 | 1993 Plymouth Colt

Not finding what you are looking for?
1997 Honda Civic Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...