Question about 2004 Lincoln LS

Open Question

2005 lincoln ls upper radiator hose seal blew out, can it be replaced

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2002 LS: aHow do I fill radiator in my V8 Lincoln LS...

First- to drain ,you can reach the drain valve,from the pass side,if you lay on the ground and reach up to the radiator. You do not even have to raise the vehicle up
Second- mix Yellow GO5 Coolant about 50/50 or 60/40. Do not use Green in a Ford or Orange GM
To Fill- Remove the front two plastic screw type buttons,from the engine cover
-Remove the cover
The radiator cap is on the front of engine,on top,it is plastic
Remove cap and that is your fill point
Run engine to warm and get thermostat open,as you would with any vehicle
Top off coolant,replace cap
VERY IMPORTANT-next to the Power Brake Booster,and just under it,is a BLEEDER HOSE;to let air out of system. Turn screw slot ,only a little,DO NOT REMOVE SCREW. When coolant runs out close.
Fill-Degas Bottle,to full line,with coolant.
Check the next couple days on resevoir level ( Degas Bottle)

Posted on May 06, 2010

Ad
  • 11 Answers

SOURCE: ac blowing hot air on 2005 lincoln ls. just sarted today

Needs to be recharged and you more than likely have a leak somewhere

Posted on Aug 05, 2009

rtpflh
  • 546 Answers

SOURCE: I plan to replace the Thermostat housing when

no sealant should be needed.clean both surfaces well.be sure 'o' ring stays in place & thermostat is installed correctly.you'll probably only fill the hose as the thermostat will be closed,but that won't hurt.keep proper level in over flow tank,it will bleed air out itself in a day or 2

Posted on Sep 23, 2009

  • 1 Answer

SOURCE: What does SVRC P mean on lincoln ls 2005

It says it where the the milage is.

Posted on Oct 01, 2009

  • 972 Answers

SOURCE: Code P0133 on Lincoln Ls V6

that is an oxegen sensor code front sensor bank 1.its on the side of the engine were #1 cylinder is located.probably bad, but it could be disconnected partialy or shorted to ground

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is it so hard to find a top radiator hose for 2005 lincoln ls v-8


Hello friend,
I am presuming you are in USA. They seem to be available here in UK as well as over there if it is a 2005 LS. See here http://www.partstrain.com/store/details/Lincoln/LS/Gates/Radiator_Hose/2005/GAT22510.html?location=Upper

Sep 09, 2014 | Cars & Trucks

2 Answers

What would cause the top radiator hose on 2005 lincoln ls v8 to blow out for a second day in a row after replacing it for just the same reason?


Overheating due to bad thermostat or bad radiator cap could cause the problem. The radiator cap vents excessive pressure to the overflow container which should also have fluid in it at all times.

Aug 27, 2014 | 2005 Lincoln LS V8

2 Answers

2000 lincoln ls 3.9 v8 boiling and running hot


check, temperature of upper radiator hose vs. lower radiator hose, also if there are any cold spots in radiator usaully indicates bad thermostat. all hoses and surface of radiator should be hot in order to keep engine cool

Aug 04, 2014 | 2000 Lincoln LS

1 Answer

Engine coolant thermostat/water outlet assembly replace for 2000 lincoln ls


First with the engine cool, drain some of the antifreeze from the radiator. Second, take the hose clamp off of the upper radiator hose on the engine side and slide the hose off the water neck, some antifreeze might spill out. Third, remove the two bolts that hold the water neck and remove the waterneck, some antifreeze may spill out. Fourth, remove the old thermostat and o-ring , clean the sealing surface and install the new thermostat and o-ring the same way it came out. Last just reverse the procedure to get it back together, tightening the two waterneck bolts to 18 ft. Lbs. Fill with 50/50 antifreeze and water start it up and check for leaks. And you are done. Should only take about 20-30 minutes

Nov 06, 2013 | Lincoln LS Cars & Trucks

1 Answer

I need a 2000 lincoln ls v6 radiator hose


You can buy all the hoses for the cars engine at any auto parts store.

Jun 20, 2012 | 2000 Lincoln LS

2 Answers

I have a 2000 Lincoln ls v6 I replaced the upper radiator hose with thermostat housing assembly and now my heater doesn't work. What could be the problem


Hi, you probably have air in the system. Park on an incline, turn the heater on, open the radiator cap, start the engine, and let it run until the thermostat opens. Keep the radiator full and when the level stops gong down your heater should be working again.

Oct 15, 2011 | 2000 Lincoln LS

1 Answer

I need to reconnect my radiator in my 2000 ls v8


For 2000 Lincoln LS 3.9L SFI DOHC 8cyl...
Radiator - Removal & Installation
  1. Drain the engine cooling system.
  2. Remove the upper radiator sight shield.
  3. Remove the air cleaner outlet tube.
  4. Remove the six bolts and the two radiator upper support brackets.
  5. Remove the upper radiator hose.
  6. Remove the bolt and position the receiver drier aside.
  7. Disconnect the dual flow coolant valve electrical connector and the A/C line from the fan shroud.
  8. 3.0L engines only:
    Disconnect the Throttle Position (TP) sensor and the Idle Air Control (IAC) valve electrical connectors.
  9. Remove the bolts.
  10. Remove the bracket.
  11. 3.9L engines only:
    Remove the bolt and position the electric water pump aside.
  12. Disconnect the high pressure cooling fan bracket and line.
  13. Inspect the seal and install a new seal if necessary.
  14. Disconnect the return hose from the cooling fan and shroud.
  15. Separate the return hose from the fan shroud and position aside.
  16. Remove the two bolts and the fan shroud assembly.
  17. Remove the A/C condenser.
  18. Remove the two bolts and position the multi-cooler assembly aside.
  19. Remove the bolts and the condenser support brackets.
  20. Remove the radiator.

To install:
  1. Install the following:

    Radiator Condenser support brackets Multi-cooler assembly A/C condenser Fan shroud assembly
  2. Connect the return hose to the fan shroud
  3. Connect the high pressure cooling fan bracket and line.
  4. 3.9L engines only:
    Replace the bolt and position the electric water pump aside.
  5. 3.0L engines only:
    Connect the Throttle Position (TP) sensor and the Idle Air Control (IAC) valve electrical connectors.
  6. Replace the following
    The upper radiator sight shield. The air cleaner outlet tube. The six bolts and the two radiator upper support brackets. The upper radiator hose. The bolt and position the receiver drier aside.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 Lincoln LS

1 Answer

Replace the radiator


Removal and Installation
On all engines
  1. Drain the engine cooling system. For additional information, refer to Cooling System Draining, Filling And Bleeding in this section.
  1. Remove the upper radiator sight shield.
  1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .
  1. Remove the six bolts and the two radiator upper support brackets.
  1. NOTE: 3.9L shown; 3.0L similar.
    Remove the upper radiator hose.
  1. Remove the bolt and position the receiver drier aside.
  1. Disconnect the dual flow coolant valve electrical connector and the A/C line from the fan shroud.
On 3.0L engines
  1. Disconnect the throttle position (TP) sensor and the idle air control (IAC) valve electrical connectors.
  1. Remove the bracket.
    1. Remove the bolts.
    1. Remove the bracket.
    1. Disconnect the high pressure cooling fan bracket and line.
    1. Using the appropriate special tool, install a new O-ring on the power steering pressure hose fitting.
    1. Separate the return hose from the fan shroud and position aside.
    1. Remove the two bolts and position the fan shroud assembly.
    1. Disconnect the return hose from the cooling fan and shroud and remove the cooling fan and shroud assembly.
    1. Remove the A/C condenser. For additional information, refer to Section 412-03 .
    1. Disconnect the lower radiator hose.
    1. Remove the two bolts and position the multi-cooler assembly aside.
    1. Remove the bolts and the condenser support brackets.
    1. Remove the radiator.

Apr 29, 2009 | 2002 Lincoln LS

5 Answers

2000 Lincoln ls overheating


There is a hose on the side of the coolant resevoir that has a straight blade screwdriver fitting in it. Open the fitting and this will bleed the heads on the LS. Without opening this you will never get the air out of the head, trust me.

Sep 26, 2008 | 2000 Lincoln LS

Not finding what you are looking for?
2004 Lincoln LS Logo

Related Topics:

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...