Question about 1991 Chevrolet C1500

1 Answer

Front and rear shock bolts are warn need help

1990 chevy 1500 2wd front and rear shock bolts are warn upper mounting bolt is round and the back rusted round tried heat spray and visgrips no luck

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,982 Answers

Only thing left now is to cut them off with a torch, chisel them off or, use a small cut-off wheel.

Posted on Jun 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Makes a funny noise when i go over a speed bump chevy 2001 mal


what sort of noise clunks&bangs could be anything from shock mounting bushes exhaust hanging mounts or suspsion bushes.it would be a good idear 2 have a mechanic put it up on a hoist 2 check it out

Sep 10, 2011 | 2001 Chevrolet Malibu

1 Answer

How to replace the rear shocks on a 1998 nissan maxima


REMOVE REAR SEAT AND PACKAGE SHELF TO GAIN ACCESS TO THE UPPER SHOCK ATTACHING NUTS.REMOVE UPPER ATTACHING NUTS. RAISE VECHICLE REMOVE REAR WHEEL AND SUPPORT THE LOWER CONTROL ARM WITH A JACK REMOVE LOWER SHOCK ABSORBER MOUNTING BOLT. REMOVE SHOCK ABSORBER ASSEMBLY FROM THE VECHICLE. COMPRESS THE COIL SPRING WITH THE PROPER SPRING COMPRESSOR TOOL. REMOVE CENTER RETAINING NUT HOLDING THE UPPER MOUNTING INSULATOR. SLOWLY DECOMPRESS THE COIL SPRING.REMOVE THE MOUNTING INSULATOR AND THE COIL SPRING. REMOVE THE COIL SPRING. TO INSTALL COMPRESSED COIL SPRING ONTO THE STRUT ASSEMBLY. BE SURE TO THE END OF THE SPRING IS IN THE NOTCH ON THE LOWER SEAT.INSTALL UPPER MOUNTING INSULATOR. YOU WILL NEW LOCKNUT FOR THE CENTER RETAINING NUT OF THE COIL SPRING. CENTER RETAINING NUT AND TORQUE THE NUT TO 13 TO 17 FT LBS. SLOWLY REMOVE THE SPRING COMPRESSOR TOOL. INSTALL SHOCK ABSORBER ASSEMBLY IN THE VECHICLE AND INSTALL THE MOUNTING FASTERNERS AND TORQUE LOWER MOUNTING BOLTS TO 72 - 87 FT LBS. INSTALL WHEEL.LOWER VECHICLE. WARNING COIL SPRING UNDER EXTREME LOADS WHEN COMPRESSED.BESURE TO PROPERLY ALIGN THE SPRING WITH THE COMPRESSING TOOL TO PREVENT PERSONAL INJURY FROM THE SPRING RELEASING UNEXPECTEDLY.

Feb 02, 2011 | 1998 Nissan Maxima

1 Answer

Dear Sir, How do you change an 87 mitsubishi mighty max front shocks without any compression equipment? Please email me at brad8141@hotmail.com. Is there a book with instructions regarding this...


REMOVAL & INSTALLATION
  1. Support the vehicle safely on jackstands. Support it at a height which will allow sufficient room to reach the upper shock absorber mount.
  2. Remove the wheel.
  3. Remove the upper shock nut, washer and bushing.
  4. Remove the lower mounting bolt(s) and remove the shock from the vehicle.
  5. Install the shock absorber in the vehicle and loosely tighten the upper shock absorber nut. Make sure the install the bushings and washers before installing the upper nut.
  6. For 4WD vehicles, install the shock absorber so that the white paint mark at the lower side of the shock absorber faces the outer side of the vehicle. Install the lower shock absorber bolt(s). On 1992-95 Montero torsion bar suspensions, tighten the single lower mounting bolt and nut to 65-76 ft. lbs. (88-103 Nm). On all other vehicles (whether torsion bar or coil spring suspensions), the two lower shock absorber mounting bolts should be tightened only to 7-10 ft. lbs. (9-14 Nm). Fig. 1: Install the shock absorber so that the white mark faces toward the outside of the vehicle - 4WD vehicles, except 1992-95 Monteros 86668006.gif
    Fig. 2: Install the bushings, washers and nuts in the order shown - except 1992-95 Monteros 86668007.gif

  7. On 1992-95 Monteros, tighten the shock absorber installation nut so that the dimensions shown in the illustration ( A and B) are at the standard values. These standard values are: A - 0.04-0.08 in. (1-2mm), B - 0.06-0.10 in. (1.5-2.5mm). WARNING
    When tightening the nut, be careful not to bend the stud pin of the washer assembly.
  8. On all other vehicles, once the lower mounting bolt(s) are tightened, tighten the upper shock absorber mounting nut all the way to the end of the thread on the shock absorber stud, then tighten the locking nut to 9-13 ft. lbs. (12-18 Nm).
  9. Install the wheel.
  10. Lower the vehicle to the ground. Fig. 3: When installing the upper shock nuts on 1992-95 Monteros, make sure measurement A is 0.04-0.08 in. (1-2mm) 86668008.gif
    Fig. 4: When installing the upper shock assembly, make sure its components are positioned as shown - 1992-95 Monteros 86668009.gif
prev.gif next.gif

Nov 03, 2010 | 1987 Mitsubishi Mighty Max

1 Answer

How to replace the shocks on my 2000 Mazda 626


REMOVE**** FRONT SHOCKS, FIRST OF ALL.SUPPORT THE LOWER CONTROL ARM WITH A JACK,REMOVE FRONT WHEEL, REMOVE BRAKE HOSE AND ABS SENSOR HARNESS TO THE STRUT BOLTS OR CLIPS,REMOVE ACTUATOR FROM TOP OF THE STRUT,IF EQUIPPED WITH AUTOMATIC ADJUSTING SUSPENSION. PAINT ALIGNMENT MARKS ON THE UPPER STRUT MOUNTING BLOCK AND STRUT TOWER AND ON THE LOWER STRUT MOUNT TO STEERING KNUCKLE SO THAT CAN BE REINSTALLED IN THE SAME POSITION. REMOVE UPPER STRUT MOUNTING NUTS, REMOVE THE STRUT TO KNUCKLE BOLTS,REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT INTO THE STRUT TOWER ALIGNING THE PAINT MARKS MADE DURING REMOVAL.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 34 - 46 FT LBS. INSTALL STRUT TO KNUCKLE BOLTS TIGHTEN TO 55 - 61 FT LBS. INSTALL ACTUATOR AND ENGAGE THE ELECTRICAL CONNECTOR IF EQUIPPED WITH AAS. INSTALL BRAKE HOSE AND ABS SENSOR HARNESS CLIPS OR BOLTS.INSTALL WHEEL AND CHECK ADJUST THE FRONT END ALIGNMENT. TO ( REPLACE REAR SHOCKS ) REMOVE REAR WHEELS, REMOVE REAR PACKAGE TRIM. REMOVE SPEED SENSOR HARNESS, REMOVE TOP STRUT NUTS,THE SUSPENSION WILL DROP WHEN THE WEIGHT LIFTS OFF THE WHEELS. REMOVE BOTTOM STRUT BOLTS.REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT ASSEMBLY, INSTALL BOTTOM STRUT MOUNT BOLTS AND TIGHTEN TO 55 - 61 FT LBS.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 33 - 46 FT LBS. INSTALL SPEED SENSOR HARNESS.INSTALL REAR PACKAGE TRIM. INSTALL REAR WHEELS.

Sep 22, 2010 | Mazda 626 Cars & Trucks

1 Answer

Need new struts on rear, Would like to replace with air shocks. Any suggestions on how I would do this?


Shock Absorber -The rear already has air shocks on the 1999 Cadillac Deville: REMOVAL & INSTALLATION Rear
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Rear wheel Fig. 1: Exploded view of the rear shock absorber mounting 9300vg06.gif

    • Negative battery cable
    • Shock absorber electrical connector from the rear suspension support, If equipped
  3. Support the lower control arm with a jack to relieve the tension on the shock absorber.
  4. Remove or disconnect the following:
    • Lower shock absorber mounting bolt and nut
    • Upper mounting nut, retainer, and insulator
    • Shock absorber compress by hand and remove through the upper control arm
    To install:
  5. Position the top of the shock absorber with the insulator attached into the suspension support.
  6. Install or connect the following:
    • Upper shock insulator, retainer and nut. Torque the nut to 55 ft. lbs. (74 Nm).
    • Shock absorber lower mounting nut/bolt. Torque the nut to 75 ft. lbs. (102 Nm).
    • Shock absorber electrical connector to the rear suspension support, if equipped
    • Rear wheel
    • Negative battery cable
prev.gif next.gif

Jul 29, 2010 | 1999 Cadillac DeVille

1 Answer

How are the shocks replaced on the e-250


You should have 1 or 2 bolts under the rear end for the rear shocks. Also, the top bolt is above the frame of the rear. For the front, there is 1 bolt above the upper spring mount which you can access with the wheel off. The bottom 2 bolts are under the lower control arm.

Sep 26, 2009 | 2004 Ford E250

1 Answer

How to replace rear shocks on 96 bmw 328i


Inside the car carefully pry up the speaker covers off the rear parcel shelf and undo the two screws that secure the speaker assembly onto the shelf. Release the clip and carefully from inside the boot pull the speakers away and disconnect the speaker connections
Open the boot and remove the carpet from the rear "wall" by unscrewing the 4 retaining "nuts" at first by hand and then using a phillips screwdriver.
bootcarpet.jpg

Lift this out and lift out the floor carpet. Carefully pull the side carpets away from the boot interior. They are held in 3 places : on one of the retaining bolts by the rear carpet, by a metal ledge at the top near the rear lights and by the ledges on the plastic parts in the boot.

Jack up the car and chock the front wheels so it can't roll anywhere. Also put something underneath the wheels so they cannot drop down when you undo the shock mounts.
reartower.jpg
Using a 13mm socket undo the two top shock mounts ONLY once you have supported the wheels so that you dont put stress on the suspension arms. Pry off the rubber dust cover.
shocklwrbolt.jpg
Undo the lower shock retaining bolt and carefully lift the entire shock away from the car.
oldcompleteshock.jpg
The old knackered shock and shock mount!
undotopmount.jpg
You need to recover the lower cup, upper cup and bump-stop from the old shock. To do this you need to remove the top mount from the old shock. If you look at the top of the piston it has a flat section to it. Get a set of mole grips and clamp them onto the flat section, do this as tight as you can so that you dont round it and using and adjustable spanner undo the piston retaining nut whilst holding the piston shaft using the molegrips.
keepthesebits.jpg
You need to recover 3 pieces from the piston shaft. 1- the bump stop, 2 - lower cup, 3 upper cup. Using the new shock mount as a template cut out a gasket from cardboard (the box the mount came in is ideal) to go between the upper shock mount and the suspension tower. Incidently according to the haynes manual this is made of rubber but mine was made of card! under no circumstances put the upper shock mount directly into the suspension tower.
newshock2.jpg
Put the 3 pieces onto the new shock and tighten the piston nut to secure the shock mount and put your new gasket onto the upper mount.
reartowernoshock.jpg
Use the opportunity to clean the suspension turret - do the top and the underneath making sure it's all clean and dry.
Put the new complete assembled shock into the suspension tower and either get someone to do up the top bolts a few turns or rest the bottom of the shock in the inner circumference of the wheel and lift it into position by lifting it up using the piston nut and then do the bolts up a few turns.
Bolt the bottom shock bolts back into place after putting some nut-lock on the threads and tighten them up securely, then tighten up the top mount securing bolts and put on the rubber dust cap.
bootcarpet.jpg
Put the side carpets back in making sure the speaker cables aren't trapped behind, putting in the end nearest the tail lights first making sure it's behind the retaining ledge both at the top and the end. Then do the centre section and finally over the bolt at the rear of the boot. Put the rear carpet back in and do up the retaining nuts. Reconnect the speakers and engage the lip and push the speaker up until the clip clips into place and do up the securing screws and clip the speaker cover back on.

About What's New BMW In-Depth How To Pages My Projects Garage Sale Galleries Communities Links Contact Donate



















































































































Jul 07, 2009 | 1999 BMW 328 Series

1 Answer

Removal of rear shocks on 1991 pontiac sunbird se


open the trunk remove the trim panel to clear the upper shock mount nut.loosen wheel nuts raise rear of vehicle support on jack stands.support trailing arm.with a jack .remove the shock absorber mounting nut and bolt.then remove the upper two bolts at wheel well above the coil spring.do one wheel at a time becauses it will damage brake lines if you remove both shocks. besure to block the front wheels to keep car from moving.

Apr 12, 2009 | 1991 Pontiac Sunbird

1 Answer

I need the rear shock torque specs for a 2007 sport trac


Torque Specifications Description Nm lb-ft lb-in Brake caliper bolt 32 24 — Brake disc shield bolt 8 — 71 Fuel tank filler pipe bracket bolt 15 11 — Fuel tank filler pipe hose clamps 3 — 27 Halfshaft nut and washer 275 203 — Lower arm inboard bolt 250 185 — Lower arm outboard bolt 275 203 — Parking brake cable bracket bolt 10 — 89 Shock absorber lower bolt 275 203 — Shock absorber rod nut 65 48 — Shock absorber upper mount nut 30 22 — Stabilizer bar bracket nut 48 35 — Stabilizer bar link nut and grommet 30 22 — Toe link cam adjuster nut 275 203 — Toe link outboard bolt 325 240 — Trailing arm bolt 300 222 — Upper arm outboard bolt 225 166 — Upper arm inboard nut 250 185 — Wheel speed sensor bolt 8 — 71 Wheel knuckle bolt 275 203 —

Mar 30, 2009 | 2007 Ford Sport Trac Limited

1 Answer

Shocks


rear
5955ba5.gif ------------------------------------------------------------------------------------------

front

Removal
  1. Remove front shock absorber-to-upper shock bracket nut and bolt.
  1. Disconnect the lower end of the front shock absorber bolt and nut from the U-bolt plate.
  1. Compress the front shock absorber and remove.
Installation
  1. Insert front shock absorber into the front shock absorber mounting bracket (18183). Insert bolt and tighten nut to 60-81 Nm (45-60 lb-ft).
  1. Attach the lower end of the front shock absorber to the U-bolt plate by installing the nut and bolt. Tighten to 60-81 Nm (45-60 lb-ft).
---------------------------------------------------------------------------------------------

front


Feb 04, 2009 | 1996 Ford F350 Crew Cab

Not finding what you are looking for?
1991 Chevrolet C1500 Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...