Question about 1999 Mercury Cougar

1 Answer

Passenger window will not go up or down. Have replaced motor and switches which did not work.

Posted by on

  • jonesspammai Jun 06, 2010

    I assume you probably did but did you check for blown fuses?

  • ryans80 Jun 07, 2010

    Yes I did check the fuse and it is OK. The passenger window does not work but the driver window does. i believe that both go thru the same fuse which confirms that the fuse is OK

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 553 Answers

According to the manuals, just about all vehicles have separate fuses for each window.

Posted on Jun 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a saturn ion 06 coupe, neither of my windows are working! I have checked the fuse replaced both motord\regulators and the switches. They're still not working!! Plz help


Please do these check and let me know.

Diagnostic Fault Information

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit/System Description

The power window system will operate any time the ignition is the ACC or RUN position. The power window system will also operate whenever the body control module (BCM) is in retained accessory power (RAP) mode. The driver power window switch contains individual window switches for each of power windows. All windows may be controlled up and down from the driver power window switch. The individual passenger power window switches will only control the up and down operation of their respective power window.
Each power window contains a reversible power window motor. The direction the window travels is dependent upon the polarity of the supply voltage. By reversing polarity of the supply voltage the window motor will move up or down. Each power window motor is internally circuit breaker protected.
Battery voltage is supplied to the power window switch through the accessory voltage supply circuit. The power window switch also receives a constant ground source. The power window motor control circuits are connected to ground through the normally closed up and down contacts of the power window switch. When the power switch is placed in the down position, the power window motor down control circuit is switched to 12 volts and is applied to the down side of the power window motor. Since the other side of the power motor is connected to ground through the normally closed contacts of the up switch, the window travels down. By placing the power window switch in the up position, the polarity of the power window motor is reversed and the window travels up.

Reference Information

Schematic Reference Power Window Schematics
Connector End View Reference Power Door Systems Connector End Views
Description and Operation Power Windows Description and Operation
Electrical Information Reference

Circuit/System Verification

Ignition ON, command the appropriate door window UP and DOWN by pressing the appropriate Window switch. Observe the operation of the appropriate door window.

Circuit/System Testing

  1. Ignition OFF, disconnect the B+ harness connector at the Driver Window Switch.
  2. Ignition OFF, test for less than 1.0 ohm of resistance between the ground circuit terminal D and ground.
  3. ?X If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal E and ground.
  5. If the test lamp does not illuminate, test the B+ circuit for an open/high resistance. If the PWR WNDW fuse is open, test the circuit terminal C for a short to ground.
  6. If all circuits test normal, test or replace the Driver Window Switch.
  7. Ignition OFF, connect the harness connector at the Driver Window Switch.
  8. Ignition OFF, disconnect the Passenger Window Switch.
  9. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal and ground.
  10. ?X If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
  11. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal H and ground.
  12. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the Driver Window Switch
  13. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal D and ground.
  14. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the Driver Window switch
  15. Connect a test lamp between control circuit terminal H and control circuit terminal D.
  16. Ignition ON, command the passenger door window UP and DOWN by pressing the passenger window control on the Driver Window Switch. The test lamp should illuminate during either of the commands.
  17. ?X If the test lamp remains OFF, test for a short to ground or open/high resistance on either control circuit. If all circuits test normal, test or replace the Driver Window Switch.
  18. Ignition OFF, reconnect the Passenger Window Switch.
  19. Ignition OFF, disconnect the harness connector at the appropriate Window Motor.
  20. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal A and ground.
  21. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the appropriate window switch.
  22. Ignition OFF, test for less than 1.0 ohm of resistance between the control circuit terminal B and ground.
  23. ?X If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, test or replace the appropriate window switch.
  24. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  25. Ignition ON, command the appropriate window UP and DOWN by pressing the appropriate Window Switch. The test lamp should turn ON when commanding the UP and DOWN states.
  26. ?X If the test lamp remains OFF during either of the commands, test for a short to ground on either control circuit. If all circuits test normal, test or replace the appropriate Window Switch
  27. If all circuits test normal, test or replace the appropriate Window Motor.

Component Testing

    Driver Window Switch
  1. Ignition OFF, disconnect the harness connector at the Driver Window switch.
  2. Test for infinite resistance between the signal terminals A and B and the B+ circuit terminal E with the passenger window switch in the INACTIVE position.
  3. ?X If less than infinite resistance, replace the Driver Window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal A and the B+ circuit terminal E with the passenger window switch in the UP position.
  5. ?X If greater than 2 ohms, replace the Driver Window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal B and the B+ circuit terminal E with the passenger window switch in the DOWN position.
  7. ?X If greater than 2 ohms, replace the Driver Window switch.
  8. Test for infinite resistance between the signal terminals F and H and the B+ circuit terminal E with the driver window switch in the INACTIVE position.
  9. ?X If less than infinite resistance, replace the Driver Window switch.
  10. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal E with the driver window switch in the UP position.
  11. ?X If greater than 2 ohms, replace the Driver Window switch.
  12. Test for less than 2 ohms of resistance between the signal terminal H and the B+ circuit terminal E with the driver window switch in the DOWN position.
  13. If greater than 2 ohms, replace the Driver Window switch
    Passenger Window Switch
  1. Ignition OFF, disconnect the harness connector at the Passenger Window switch.
  2. Test for infinite resistance between the signal terminals G and F and the B+ circuit terminal with the switch in the INACTIVE position.
  3. ?X If less than infinite resistance, replace the appropriate passenger Window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal G and the B+ circuit terminal with the switch in the UP position.
  5. ?X If greater than 2 ohms, replace the appropriate passenger Window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal with the switch in the DOWN position.
  7. ?X If greater than 2 ohms, replace the appropriate passenger Window switch.
      Window Motor
    1. Install a 30-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The appropriate Window Motor should perform the UP or DOWN function.
    2. ?X If the function does not perform as specified, replace the appropriate Window Motor.
    3. Reverse the jumper wires; the appropriate Window Motor should perform the DOWN or UP function.
    4. ?X If the function does not perform as specified, replace the appropriate Window Motor

Mar 25, 2015 | 2006 Saturn ION

2 Answers

2000 Mitsubishi Galant rear window only goes down not up passenger side motor and regulator are fine replaced with new one replaced both switches getting power going up and down to motor hot wired the...


if you hot wired it straight to the motor and it works up and down fine chances are you have a broken or shorted wire between the button switch and the motor itself possibly between where the door opens and shuts at the hinge

Jan 02, 2015 | Cars & Trucks

1 Answer

Window not working


Replace the window regulator. It comes with a motor.

Nov 01, 2014 | Cars & Trucks

1 Answer

Why my passenger window don't work ?


If neitrher the driver's door master switch nor the passenger door window switch wont operate the window, and the lock-out button is not on, then likely the passenger door inner panel has to come off to investigate. But first, check the wiring going into the passenger door for a broken wire. Also check the wiring coming out of the driver's door. If you see nothing wrong, pull off the passenger door panel and check for any wires loose from the window switch down to the motor. You can hotwire the window motor with a spare battery set beside the door there, to verify the motor is bad. If it is bad, you have to remove the glass, then remove the window regulator with motor attached, in order to replace the motor.

Nov 14, 2012 | 2004 Ford Mustang

2 Answers

My passenger window wont go down using either switch on drivers side or passenger


Try replacing the motor. If motor fails it doesn't work. Have a glance at this to know about its price.
http://www.buyautoparts.com/part/replacement-window-motor/

Mar 16, 2011 | Dodge Caravan Cars & Trucks

1 Answer

I have a 1994 Toyota Camry and the power window on the passenger side has gone down, under power. Then nothing would happen when I would pulled up on the switch on the driver side main switch and the also...


more than likely one of the switches are bad (down side of switch works but up side of switch dont) being as the switches are wired together if one goes bad other one won't work either take the switch out one of back doors should be same as front passenger door put rear switch in front passenger door if works then u know front door switch is bad if it doesn't then drivers door switch is bad
u replaced window regulator Did that come with motor too??? if not check to see if motor is good
there is two wires going to motor cut isolation back on wires and using some jumper wires attach one wire to positive terminal of a 12 volt battery attach other wire to negative terminal of battery window should move up or down reverse connections and window should move other way

Jan 29, 2011 | 1994 Toyota Camry

1 Answer

95 nissan quest front passenger side power window does


driver side switch is not working replace it

Oct 12, 2009 | 1995 Nissan Quest

3 Answers

Passenger window will not go up i think its


if the fuse was an issue then all the windows would be inop, not just one, the most common fault is the electric motor that runs the window up and down.

Oct 03, 2009 | 2003 Ford Expedition

1 Answer

Window switch for driver control and passenger switch window


sounds like you have a passenger window motor problem. Try hitting the right door panel hard, down near the speaker opening and pushing the switch at the same time. If it moves, the motor windings are and needs to be replaced.

Mar 26, 2009 | 1999 Mercury Grand Marquis

1 Answer

Passenger window will go down not up


the clutch inside the mechanism is bad, need to replace unit

Mar 11, 2009 | 2003 Mercury Mountaineer

Not finding what you are looking for?
1999 Mercury Cougar Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...