Question about 1999 GMC Yukon

1 Answer

Replaced starter on '99 Yukon. When reconnected

Replaced starter on '99 Yukon. When reconnected battery cable the warning signal began beeping and flashers flashing without key in ignition. Will not shut off. Why?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 553 Answers

I can't say for sure but it sound like you either trigger the "Panic" button or alarm system if equiped. Hook the battery up (negative last) and push the "Panic" button on the key FOB.
If you don't have the FOB you may be able to reset but disconnecting the negative cable only.
If it's an alarm system, locking and then unlocking with the FOB should reset it, also using the key to turn on the ignition is supposed to reset it.

Posted on Jun 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What can be the problem when I turn the key to start my yukon and the engine does not turn over but one click sound occurs at the starter location and then nothing?


Make sure your engine is not seized up. If the engine cannot rotate, neither will the starter. Next step is to determine that the car can control the starter. Easiest way to do this is to jump the battery and solenoid wires at the starter, in the car, while it is in park or neutral, with the ignition on. If the starter can be made to manually start the vehicle, the problem is in the control circuit. If not, either the new starter is no good or you still have power cabling or battery issues.

Mar 11, 2015 | 1998 GMC Yukon

1 Answer

Engine will not start


Is the engine locked up ? Before i replaced all that i would have put jimper cables on the battery and jumped the starter with a screwdriver to see if it worked and the engine turns.

Sep 06, 2014 | 2004 GMC Yukon

1 Answer

99 yukon denali drivers side turn signal in rear tail light not working, i replaced bulb and still nothing, I looked at the connections and wires and found nothing, front turn signal blinks fast, passenger...


The circuit board needs to be replaced. Which is the board that the bulbs sit in. If you remove the turn signal bulb. You will notice the bulb socket will be slightly burnt inside. I had the same problem with my 99 Denali and replaced the circuit board for $35.00. Now everything is fine.

Feb 01, 2011 | 1999 GMC Yukon Denali

1 Answer

I changed the battery in my 05 GMC Yukon and when I tried to reconnect the terminal I am getting a arch. First I reconnected the neg. and when tried to reconnect the pos it arched, then I started over and...


If you are talking about a big spark, then I would say you have a positive batt cable that is shorted to the frame or engine somewhere. Follow it down to the starter. Also check the wire that goes to the alternator. Is the insulation rubbed off, or is it pinched anywhere?

Aug 14, 2010 | 2005 GMC Yukon

1 Answer

Yukon 99 vibrate badly below 60 kmph spd


sounds like a misfire.check all the wires are tight to the plugs.,or do a compression test .if the compression is good,then it has to be electrical

Dec 08, 2009 | GMC Yukon Cars & Trucks

1 Answer

Have a 2000 yukon denali, the car wont turn over, replaced the battery still wont turn over is it the starter or could it be the relay?


The next thing to check is the amount of corrosion at the other end of the heavy battery cables; any car exposed to road spray will eventually develop problems at the starter or where the negative cable connects to chassis or block. Any cable connecting these two should also be removed and cleaned.
Remember to ALWAYS disconnect the negative battery terminal first to avoid damage to tools and vehicle.

Dec 02, 2009 | 2000 GMC Yukon Denali

1 Answer

Ignition turns and key warning light comes on. Its a 98 Ford Expl


Sounds Like the Starter RELAY is Bad After Exhausting All other Test, Go For The RELAY
A SURE-SHOT way Is to Jumper Wire From Battery to (STARTER SIDE) of Relay if starter Works then Its the Starter Relay if NOT>>Then Its the STARTER<) Relay Instruction Below. STARTER Instructions Very Bottom
REMOVAL
WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE.

  1. Disconnect the battery ground cable.
    1. Disconnect the starter motor solenoid relay switch wiring.
    1. Remove the protective cover.
    2. Disconnect the push-on electrical connector.
    3. Remove the nuts.
    4. Remove the cable.
      1. Remove the starter motor solenoid relay switch.
      1. Remove the engine sensor/generator wires.
      2. Remove the bolts and ground wire.
      3. Remove the starter motor solenoid relay switch.
      INSTALLATION
    5. Follow the removal procedure in reverse order NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.
REMOVAL

WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE WHEN MAINTENANCE IS COMPLETED.

  1. Disconnect the battery ground cable.
  2. Raise and support the vehicle.
  3. Remove the starter motor solenoid terminal cover.
    1. Disconnect the starter wires.
    1. Remove the nuts.
    2. Disconnect the wires.Remove the nut and the starter ground cable
    3. Remove the bolt and the starter motor.
      1. Follow the removal procedure in reverse order. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

Feb 08, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
1999 GMC Yukon Logo

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...