Question about 2003 Mercury Sable

1 Answer

My rear turn signals are not working i have checked all the fuses is it the flasher ? if so where is it located

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 553 Answers

Try your 4-way flashers, turn them on, walk around the car look for a burned out bulbs.
If your rear bulbs are still out then the problem is either burned out bulbs or wiring.

Posted on Jun 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

My saturn signal light work sometime than go off if it the flasher please tell me there it is in my car


IF TURN SIGNAL LIGHT DONT WORK SOME TIMES.CHECK FOR BLOWED OR LOOSE FUSE.CHECK TURN SIGNAL BULBS AND CHECK BULB SOCKETS FOR CORROSION.CHECK TURN SIGNAL FOR BAD GROUND.USE JUMPER WIRE BETWEEN GROUND SIDE OF THE TURN SIGNAL BULBS AND A GOOD CHASIS GROUND.IF ALL IS GOOD TURN SIGNAL SWITCH IS BAD OR FLASHERS GOING BAD.TURN SIGNAL FLASHER LOCATED ON CENTER CONSOLE SIDE PANEL GRASP THE FLASHER UNIT AND DETACH IT FROM THE FUSE BOX.IF YOU HAVE EARLY MODEL VECHICLE FLASHER UNIT LOCATED AT THE FRONT OF THE FUSE BLOCK.

Aug 23, 2011 | Saturn LS Cars & Trucks

1 Answer

1999 jeep grand cherokee - rear driver turn signal and brake light don't work. flasher, back up and running light works. everything works when lens assembly is plugged into the passenger side. can...


Check this diagram (click over pic for zoom)...

zjlimited_1040.jpg

Check the postion F4 / 15 Amp ( Lt. Blue ) Flasher, hazard switch (see Junction Block diagram above for location of turn signal Flasher relay - Mopar p/n 4686094)

Repair tip: WJ flasher repair.

Hope helps.

Apr 16, 2011 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Both of the rear turn signals stopped working at the same time, but everything else seems to work. Do you know what can cause this to happen? I changed one of the bulbs and it didn't work.


There is a turn signal flasher under dash...most have a flasher for the emergency signals and one for the turn signals...some have one flasher....but check fuses first...normally it is fuse burnt...if you can locate the flasher normally they will get abnormally warm when bad......it should look like a round or square silver shiney or black cube.........if these are good with ign.on hold turn signal lever down firmly ...if it works replace turn signal unit.....if none of this works you have to troubleshoot wiring...
...normally yellow wire is left turn and green wire is right turn...black or white is ground red is stop light....but normally it is a blown fuse or flasher.

Feb 19, 2011 | 2007 Ford Freestyle Limited

1 Answer

My turn signals and emergency flashers work some time where is the turn signal flasher relay located and how do you detach it?


For 1998 Ford Truck Explorer 4WD 4.0L EFI SOHC 6cyl the Flasher is located in front seating area, driver side, behind dash, mounted on steering column.

Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel.

The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel.

Hope helps.

Jan 26, 2011 | 1998 Ford Explorer

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

1 Answer

Both front and rear turn signals stopped working


Your turn signal flasher needs to be replaced (the hazard flasher is separate unit). Your owners manual should have the location of the turn signal flasher (usually on the fuse block under the dash).

Mar 19, 2009 | 1999 Ford Contour

3 Answers

Blinkers stopped working


Your F--150 has 2 flashers, emergency and turn signal. Both are mounted on the fuse block under the dash. The turn signal flasher is mounted on the front of the fuse panel, the emergency flasher is mounted on the rear of the fuse panel. so replace the turn signal flasher should solve the problem. Let me know how it goes.

Oct 20, 2008 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
2003 Mercury Sable Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...