Question about 1990 Dodge Dynasty

1 Answer

What is the part called that the rear shocks on a Dodge Dynsty 1990 are mounted on?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

The rear axle?

Posted on Jun 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New rear suspension and they make noise


Caravans had a real issue with rear suspension noises, and one of the suggestions from Dodge was the addition of a spacer washer at the bottom shock mount to space it a little farther away from the axle housing. I have seen many new shocks that "knocked" right out of the box new. It is possible one of the new ones is defective

Apr 21, 2013 | Dodge Caravan Cars & Trucks

1 Answer

Where does the top part of shock mount on 1990 mercury grand marquis?


Strut tower in plain site, if you open the hood,
should have 3 nuts to remove for top bearing plate

The rear ones may be in the trunk

Jan 22, 2013 | 1990 Mercury Grand Marquis

1 Answer

1990 dodge truck new alt. still won,t charge


Your truck uses an external regulator. I would change that part. It is located Under hood, center, rear engine area, mounted on upper firewall

and looks like this:

chuckster57_30.jpg

Feb 26, 2011 | 1990 Dodge D150

1 Answer

Front and rear shock bolts are warn need help


Only thing left now is to cut them off with a torch, chisel them off or, use a small cut-off wheel.

Jun 06, 2010 | 1991 Chevrolet C1500

1 Answer

How do you remove the front shocks on a 2004 Dodge Durango 4X4?


how do you remove the front shocks on a 2004 durango limited 4x4. the stabilizer bar and axle links appear to be the way for removing the lower shock mounting bolt

Apr 29, 2010 | 2004 Dodge Durango

1 Answer

Do i have to remove the back seat to take rear struts off


Answer
REMOVAL - SHOCK ASSEMBLY
NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.

Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
Remove plastic cover from the top of the shock assembly.
Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
Raise vehicle on jackstands or centered on a frame contact type hoist. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
Remove the rear wheel and tire assembly from the vehicle.
Remove two fasteners holding the splash shield to the shock assembly upper mount.
Remove bolt attaching shock absorber to rear knuckle (Shock Absorber Attachment To Knuckle).
Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening

Nov 23, 2009 | 2002 Dodge Stratus

1 Answer

1990 dodge dynsty le the factory alarm is set and we cannot get it to turn off. we have tried to unlock doors from both sides of vehicle and have turned ignition on and off but still no luck. car ran fin...


In 1990 the alarm installed by chrysler was still considered after market. The problem is you have to find the control box. If this alarm is giving you this problem now you might as well find the box and remove it from the electrical system. It is usually located near the fuse panel or steering column. Now you would think it would have plug connectors but it might not. Since alarms where not incorporated into the ECM in that year you are looking for a small black box with 4 to 6 wires on one side comeing from teh ignition switch area and running through the firewall. If you have an alarm horn it is possible that you might find an in-line fuse you can pull to resolve this issue, You will have to trace the wires. If it were incorporated in the vehicles original design there would be a fuse in the fuse block you could pull.

Oct 07, 2009 | 1990 Dodge Dynasty

1 Answer

Jumps up and down at rear when braking


check front motor mounts. Hold brake and put in reverse then accelerate and let up on gas. do yhe same in forward gear.if you hear a thud a motor mount is broken with hood open you can see the motor lift up.. Acceleration causes engine to lift and drop. good luck

May 10, 2009 | 1990 Dodge D150

1 Answer

2004 dodge stratus SE


This is a dangerous job if you do not have the proper equipment for compressing the spring that is around the rear shock. I do not recomend performing this job without the proper equipment. Unloading the spring without it compressed can cuase injury.

If you have the proper equipment this is how you do it.

REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
  1. Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
  2. Remove plastic cover from the top of the shock assembly.
  3. Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
  4. Raise vehicle on jackstands or centered on a frame contact type hoist.
  5. Remove the rear wheel and tire assembly from the vehicle.
  6. Remove two fasteners holding the splash shield to the shock assembly upper mount.
  7. Remove bolt attaching shock absorber to rear knuckle
  8. Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
  9. Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening.

Aug 04, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
1990 Dodge Dynasty Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...