Question about 1998 Ford F150 Regular Cab

1 Answer

Keyless remotes not working

Keyless remote quit working. Installed new batteries. Still neither remote works. Checked fuse for remote enrtry module. Fuse okay.

Posted by on

  • bensacci Aug 17, 2013

    the keyless remote for my 2012 4runner doesn't work. I've replaced the battery and it still doesnt work. I haven't driven the SUV for about 6 weeks... could it be that the battery is dead? If so, how do I get in?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 80 Answers

Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:

  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Posted on Jun 06, 2010

Testimonial: "Great advice. This fix worked great. "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 crown vic keyfob only works with ignition in run position .keyless entry and door locks work fine.even tried new keyfob.no change


The keyless entry system consists of the following components:
  • driver door module (DDM)
  • keyless entry transmitter
  • keyless entry keypad
The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness
  • If fuse's good have checked for DTC'S - diagnostic trouble codes .
  • B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .
  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter not programmed.
  • Remote transmitter.
  • DDM.
  • Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Feb 19, 2017 | Cars & Trucks

1 Answer

2000 toyota avalon keyless remote won't open/close the car; checked with Auto Zone, fob is responding which means it is no battery, tried reprogaming and it stops when tried using fob, what else should...


2000 Avalon keyless remotes stopped working: solution Both keyless remotes for my 2000 Avalon stopped working. The batteries were good (I checked them with a volt-ohm meter). The Toyota dealer determined that the remote used most was defective and it tried to initialize the receiver in the car. This caused the second remote also not to work. The dealer reset the receiver (reinitialized it after first unplugging it), replaced the defective remote with a new one, and reprogrammed both remotes. Total cost: $225 labor, 164 for new remote. Later, another remote went bad. I just stopped using it.

Dec 13, 2012 | 2000 Toyota Avalon

1 Answer

I have a 2003 Vw Jetta Gt. My keyless entry remote stopped working a couple of days ago. I have 2 so I tried to use the other one but it didn't work either. I changed the batteries in both and I also...


KEY WORDS to search for are
2003+VOLKSWAGEN+remote+receiver...

or "keyless+module"

I only got hits back from eBay (& AMAZON)...
which would indicate this is a fairly ROBUST part...
(TYPICALLY: really popular parts = high failure rate).
((in my opinion))


No direct
(part number) hits...!!


Look here... Appears to be inside the center console
(surmised without proper documentation)

Looks like
VW VOLKSWAGEN OEM Phaeton Keyless Entry Receiver for Key Fob Remote...

also...
VW VOLKSWAGEN OEM Phaeton Keyless Entry Receiver for Key Fob Remote...

Possibly AMAZON... (use your own module number)
EXAMPLE
Amazon com 2003 jetta keyless module

Hope I am helping...

Carnac the Magnificent

Sep 15, 2017 | 2003 Volkswagen Jetta TDI

1 Answer

2007 gmc yukon. Keyless Entry problem. The remote quit working but the gmc place said its not the battery. Help


Disconnect the battery to the car for five mins. Thay should reset the keyless module. I had the same problem

May 20, 2010 | Cars & Trucks

1 Answer

2003 Mazda6 keyless quit working I put a new battery in the remote, had the remote checked, and tryed programing it and I can not get it to work?


You need to have the body control module checked, because the 6 body seams leak water that will get the body control module wet, which then short-circuits it.

Jul 10, 2009 | 2003 Mazda Mazda6

1 Answer

Keyless entry doesn't work, batteries good in transmitter,fuses good


there is a tester that checks for Rf signals from your remote. if the batteries are good, you should get a strong signal from it. most likely the remote went bad

May 09, 2009 | Dodge Dakota Cars & Trucks

1 Answer

How do i program remote keyless entry? I replaced the battery and keyless entry quit working,


You don't normally program a keyless entry, that's done for you by the technicians that install that. If the replaced battery doesn't solve the problem, take the battery and the remote to the techies that installed it.

Mar 27, 2009 | 2003 Chevrolet Monte Carlo

3 Answers

Keyless entry for 05 Kia Sportage


i have a kia optima my keyless quit working to.I took it back to the dealer and the said it was common on a lot of kia models.They replaced the module for the keyless remote,that seams to have fixed it.

Mar 17, 2009 | 2004 Kia Optima

1 Answer

Keyless remote works intermittently


replace the battery in your remote, or have it checked at autozone to make sure it's not just your remote.

Oct 24, 2008 | 1992 Buick LeSabre

1 Answer

There is no sound from the horn when I press on the horn in the steering column or when I hit the panic button on the keyless entry remote. I have checked the fuse and it is good, also have checked the...


my keyless entry has been working great we went on vacation. it quit working i cheched the fuses and the battery in the remote everything is fine just does not work anymore

Jul 22, 2008 | 2005 Ford Escape

Not finding what you are looking for?
1998 Ford F150 Regular Cab Logo

4,834 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...