Question about 1972 Oldsmobile 98

1 Answer

Need a diagram of '84 olds ''98'' steering column inner parts placement or assembly , turn signal cancelation part for a tilt and telescoptic column

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1985 olds delta 88 steering column key removely

Posted on Feb 12, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dismantle also re-assembly - '1991 Chevrolet C1500' Steering Column (Wheel Wobble)


All GM steering columns in this year are the same part with just minor diffs in switches. Follow the instructions at the link Illustrated tilt steering column disassembly

Sep 30, 2016 | Chevrolet Cars & Trucks

1 Answer

Need parts diagram for steering column on 88 Jeep Cherokee Limited


you can get great diagrams from AA1CAR.COM all are free i my self have had great results

Oct 29, 2012 | 1988 Jeep Cherokee

2 Answers

How to replace the turn signal switch in a 1992 Cadilac?


Turn Signal Switch REMOVAL & INSTALLATION CAUTION
Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column, and instrument panel disable the SRS. Deville, Eldorado, Seville, and Fleetwood - Early Models
  1. Disable the SIR system.
    1. On Deville and Fleetwood, remove the left lower sound insulator. On Eldorado and Seville, remove the left side sound insulator.
    2. Remove the Connector Position Assurance (CPA) and detach the yellow 2-way connector at the base of the steering column.
    3. Remove the steering wheel.
    4. Make sure the ignition switch is in the LOCK position to prevent the SIR coil assembly from going off-center.
  2. Remove the SIR coil assembly retaining ring and the coil assembly. Allow the coil to hang freely. WARNING
    The SIR coil assembly will become off-center if the steering column is separated from the steering gear and is allowed to rotate or if the centering spring is pushed down, letting the hub rotate while the coil is removed from the column.
  3. Remove the wave washer.
  4. Use tool J-23653-C or equivalents, to depress the shaft lock, then remove and discard the shaft lock retaining ring.
  5. Remove the shaft lock.
  6. Remove the turn signal canceling cam assembly.
  7. Remove the upper bearing spring, upper bearing inner race seat and inner race.
  8. Move the turn signal switch to the RIGHT TURN position.
  9. On Deville, Fleetwood, and 1990 Eldorado, and Seville, remove the multi-function turn signal lever as follows:
    1. Make sure the lever is in the OFF position.
    2. Remove the access cover from the steering column housing.
    3. Detach the cruise control wiring connector. Note the position of the connector when installed in the column.
    4. Pull the lever straight out of the turn signal switch.
  10. On Eldorado and Seville, remove the multi-function turn signal lever as follows:
    1. On 1992-93 vehicles, slide the connector cover toward the front of the vehicle.
    2. Unplug the electrical connector. On 1991 vehicles, note the position of the connector when installed in the column.
    3. Push the lever straight in, rotate clockwise 1?4 turn and pull the lever out of the switch.
  11. On Deville, Fleetwood, and Eldorado and Seville, remove the screw, button, spring, and hazard warning switch knob.
  12. On Deville and Fleetwood, remove the one signal switch arm retaining screw. On Eldorado and Seville, remove the 2 signal switch arm retaining screws. Remove the signal switch arm.
  13. Remove the turn signal switch retaining screws.
  14. Remove the wiring protector and detach the turn signal switch connector.
  15. Gently pull the wire harness through the column and remove the turn signal switch. prev.gif next.gif

Nov 12, 2010 | 1992 Cadillac DeVille

1 Answer

My steering wheel has lots of play up and down , side to side i removed steering wheel i'm stuck on how to get the rest apart to tighten bolts in steering column


you're best to remove the entire column and do it in the bench, if you can get a diagram it will help a lot, assembilng a steering column is tricky, some parts are spring loaded and others only assemble in in the proper order, you got the steering column out, now you will need a tool to depress the lock plate, remove the c clip and the plate, then remove the signal arm and fourway button, remove the signal switch plate remember how everything came out,you should be able to remove the steerin shafe and get at the four bolts holding the tilt mechanism, four reverse torx bolts, reassemble and install, good luck

Apr 30, 2010 | 1991 Chevrolet C1500

1 Answer

I need to install my cruise control switch on my steering wheel . How do I go about removing the back cover on the steering wheel?


Removal & Installataion
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
ca4e20e.gif
Exploded view of the shroud-type steering column showing shrouds, wiring and multifunction switch that includes the headlamp function

    1. Remove the upper and lower steering wheel trim covers using the following procedure.
    2. Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
    1. Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
    2. Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
    To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.
    1. Disable the SIR system.
    2. Remove the upper and lower trim covers.
    3. Remove the knee bolster.
      NOTE The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.

    4. Remove the wire harness assembly from the wire harness strap.
    5. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
    6. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
    7. Remove the 2 pan head tapping screws and from the turn signal and multifunction switch assembly.
    8. Remove the turn signal and multifunction switch assembly from the steering column tilt head assembly.
    To install:
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    CAUTION Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

    CAUTION The abrasion sleeve must be installed back onto the steering column wire harness assembly. The ignition lock cylinder case wires and connector must be hanging out of the middle of the abrasion sleeve.

    1. To install, reverse removal procedure.
    2. Tighten the following to specification.
      • Top pan head tapping screw: 27 inch lbs. (3 Nm).
      • Side pan head tapping screw: 62 inch lbs. (7 Nm).
    CAUTION When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

    Dec 08, 2009 | 2005 Chevrolet Impala

    1 Answer

    How to remove key unit from steering column 1986 F150 Ford


    COUTESY OF EXPERT "C17HYDRO"
    With Key
    1. Disconnect the battery ground.
    2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
    3. Remove the trim shroud halves.
    4. Unplug the wire connector at the key warning switch.
    5. Place the shift lever in PARK and turn the key to ON.
    6. Place a 1/8 in. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
    7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
    8. The remainder of installation is the reverse of removal.

    This section is for a NON-TILT with no key or non-functioning cylinder:
    Fixed Columns
    1. Disconnect the battery ground.
    2. Remove the steering wheel.
    3. Remove the turn signal lever.
    4. Remove the column trim shrouds.
    5. Unbolt the steering column and lower it carefully.
    6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
    7. Remove the turn signal switch.
    8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
    9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
    10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
    11. Upon reassembly, the following parts must be replaced with new parts:
      • Flange
      • Lock cylinder assembly
      • Steering column lock gear
      • Steering column lock bearing
      • Steering column upper bearing retainer
      • Lock actuator assembly
    1. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the vehicle starts only in PARK and NEUTRAL.

    This section is for TILT and no key or non-functioning cylinder:

    Tilt Columns
    1. Disconnect the battery ground.
    2. Remove the steering column shrouds.
    3. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Cover the entire circumference of the casting. Cover the seat and floor area with a drop-cloth.
    4. Pull out the hazard switch and tape it in a downward position.
    5. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button.
    6. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch.
    7. Using a 1/8 in. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/2 in. (12.7mm).
    8. Tilt the column to the full down position. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder.
    9. Using a 3/8 in. drill bit, drill down the center of the ignition lock cylinder key slot about 13/4 in. (44mm), until the lock cylinder breaks loose from the steering column cover casting.
    10. Remove the lock cylinder and the drill shavings.
    11. Remove the steering wheel.
    12. Remove the turn signal lever.
    13. Remove the turn signal switch attaching screws.
    14. Remove the key buzzer attaching screw.
    15. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring.
    16. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. The removal of the casting cover will expose the upper actuator. Remove the upper actuator.
    17. Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.
    18. Clean all components and replace any that appear damaged or worn.
    19. Installation is the reverse of removal. Check for proper operation.

    Nov 23, 2009 | 1986 Ford F150 SuperCab

    2 Answers

    Having problems with my turn signals, they do not work when i just click the turn signal, I have to hold them in a specific way for them to come on.


    step by step heres what you got to do
    1.disconnect battery ground cable
    2.remove nut retainer and jam nuts hten steering wheel
    3.remove turn signal cancel cam assembly
    4.remove hazard warning screw and knob
    5.move the turn signal switchso you can access the turn signal screws and housing screws which can be accessed through the opening in the switch
    6.remove housing screws and housing
    7.only on models with tilt steering wheels remove shoe pin retainer cap
    8.remove pivot switch screw and pivot pluse switch assembly
    9.remove turn signal screws
    10.remove wire prtecting from opening in instrument panel bracket assemblyand seperate from wires
    11.disconnect turn signal switch connector from ignition and dimmer switch assembly connector
    12.disconnect 17 wy lock from turn signal connector
    13.use ternimnal tool #j-35689-a or equivelent, disconnect wires on buzzer switch assemble from turn signal connector
    14.remove turn signal switch assembly from column
    15 reverse to put back together
    16. please note that signal and column housing screws got to be torqued to 35 inch lbs the switch screws at 20 inch lbs hazards at 7 inch lbsand the jam nuts at 30 ft lbs

    Nov 21, 2009 | 1992 Pontiac Grand Prix

    2 Answers

    Diagram on to change turn signal arm on 1994 chevy cavalier , do u have to pull the sterring wheel


    1991-94 Cavalier
    See Figure 5
    This procedure covers removal and installation of the headlamp, headlamp dimmer switch, turn signal and hazard switches, as well as the cruise control switch.
    1. If equipped, disable the SIR system. For details, please refer to the procedure located in of this repair guide.



    0900c1528003bf08.jpg enlarge_icon.gif enlarge_tooltip.gif Fig. Fig. 5: View of the steering column showing the turn signal switch location
    1. If not already done, disconnect the negative battery cable.
    2. Unfasten the horn pad, then remove the steering wheel. For details, please refer to the procedure earlier in this section.

    If necessary, using locking pliers with a piece of rubber (such as a spark plug boot) between the jaws to help prevent damage to the tilt lever during removal.
    1. If equipped, remove the tilt lever from the steering column by grasping the lever firmly and twisting counterclockwise, while pulling it from the column.
    2. Remove the upper and lower steering column covers.
    3. Remove the dampener assembly, then unfasten and remove the switch assembly from the vehicle.

    To install:
    1. Position and secure the switch assembly.
    2. Install the dampener and the upper and lower steering column covers.
    3. If equipped, attach the tilt lever to the column.
    4. Install the steering wheel, then fasten the horn pad.
    5. If equipped, enable the SIR system, as outlined in of this repair guide.
    6. Connect the negative battery cable.

    Nov 15, 2009 | 1994 Chevrolet Cavalier

    1 Answer

    I have a 1973 Camaro with the factory tilt steering column and it's starting to get loose. What does it take to fix this? Are there any part breakdown diagrams?


    if you can, pull steering wheel, steering lock wheel(spring compressor needed,from auto parts store,free) pull signal switch (three screws) out far enogh to see tilt mechinizm, there are three black bolts to be tightened, if you wiggle the tilt column you should see them loose, a small socket will fit star shaped bolt heads

    Apr 25, 2009 | Chevrolet Camaro Cars & Trucks

    1 Answer

    Wobbly tilt wheel


    Remove horn pad . After removing the large nut SCRIBE A LINE ON THE CENTER SHAFT and the STEERING WHEEL, Using a steering wheel puller, remove steering wheel. Now comes the tricky part. Remove signal stalk ( just pull out a couple of inches ),and 4-way flasher knob. Disconnect multiple connector of signal switch. Remove 3 screws holing switch down. Gently pull upward on switch to expose lower steering bowl. The large bolts are LOOSE that secure it, so the reason for the wobble. Tighten bolts, and reverse procedure.

    Mar 31, 2009 | Oldsmobile 88 Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    298 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...