Question about 2007 Toyota RAV4

Open Question

Can you change the water pump on a 2997 rav 4 2.2d with the engine fitted

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Water pump

It took approximately 45 minutes to remove the alternator, the belt and the water pump. it then took another 45 minutes to put everything back in place. it was extremly easy!

Posted on Nov 12, 2008

Ad
michigan man
  • 3533 Answers

SOURCE: I need to change the

go to an auto zone because they can give you a print out and also ask them to let you look at the head gasket and the will give you an idea of you are dealing with

Posted on Jan 05, 2009

  • 160 Answers

SOURCE: The Heater core is leaking on my 1998 RAV 4. Has

You do in fact have to take most of the dash board off. Actually it's not that drastic but you do have to take the glove box out and possibly the center console of the dash. Then you can get to it. Not easy, but not too hard. Lots of screws is all.

Posted on Jul 03, 2009

  • 701 Answers

SOURCE: Easiest way to change a fuel pump oa a 1999 toyota

Hello mm500539: My name is Roger and I will help. To locate the fuel pump you will need to remove the left rear seat. Remove the carpet. Remove the access cover in the floor pan. Drain off the fuel pressure as it should be under pressure. Do not expose to any spark or flame. Remove the screws holding the fuel pump unit in the fuel tank. Change the pump and reverse the procedure the reinstall the unit. Should you need further help please just ask. Please rate the answer you received as this way i know it was helpful. Thank You for using Fix Ya. Roger

Posted on Jan 08, 2010

  • 202 Answers

SOURCE: 1999 toyota rav 4 engine oil cooler bolt torque setting

INSTALL OIL COOLER
-clean the oil cooler contact surface on the oil cooled mounting
-install a new O-ring to the oil cooler.
-temporarily install the oil cooler with the nut
-apply a light coat of engine oi on the threads and under the head of the relief vale
-install the plate washer and union bolt. torque 78Nm (800kgfcm, 58 ft lbs.)
-tighten the nut,torque 8.8Nm (90kgfcm, 78 inch lbs.)
-connect the 2 water bypass hoses to the oil cooler.

HOPE THIS CAN HELP.

Posted on Apr 26, 2010

Testimonial: "Great work thanks for the info."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi can anyone tell me would a 2000 5 speed fit into a 1997 rav 4 ?


According to the description on eBay a 2000 rav 4 transmission should fit in a 97 rav 4.

http://www.ebay.com/itm/Toyota-Automatic-Transmission-Tested-Good-/301940403279?fits=Make%3AToyota'Model%3ARAV4

Apr 29, 2016 | Cars & Trucks

1 Answer

Where is the TCM located on a 2997 Jeep Grand Cherokee Larado, 4 liter, 4 wheel drive


2997, my cystable ball is too fogging out 900 years,
my guess, is there gas pumps are long ago dry....
we walk now.
most cars the TCM is now in the pCM.
just about that year for most cars. (integrated now)
if posted the manual now 10000 times.
guess 1. ZJ jeeps
8w31-1
and there IS NO TCM
just TCC locker.




25969931-mgmuftjmuwumvfkqzzfa3nwy-3-0.jpg why not post symptoms first. then we can easter egg hunt all day.

Nov 20, 2015 | Jeep Cars & Trucks

1 Answer

Why fuel does not go through pump? Toyota rav 4 d4d engine


1 Blocked fuel filter = fit new filter and bleed fuel lines
2 Air in fuel lines = check fuel lines for cracks, repair and bleed fuel lines
3 No fuel = fuel car, bleed fuel lines

Dec 29, 2014 | Toyota Cars & Trucks

1 Answer

When to change cam belt on 407 hdi 1600 cc ?


It should be changed every 50000 mile's. When changing the cam belt on these engines be sure to fit a new water pump and pulley's. The water pump most of all. It is driven with the cam belt and they can and do fail. Can lead to complete engine rebuild.

Aug 11, 2014 | Cars & Trucks

2 Answers

Is it very difficult to change the cam iol seal on a 2.0 toyota rav 4 1999, and is there anything I should know that the book doesn't tell


pulling the timing belt on older RAV4 engines is a more difficult task but not impossible.

Do you have some experience with timing belts and or cars in general?

Apr 05, 2013 | 1999 Toyota RAV4

1 Answer

Is the water pump on a 2007 rav 4 internal or external


Its internal.

Here's a How To: http://www.ehow.com/how_4914451_replace-water-pump-rav.html

Jul 27, 2010 | 2007 Toyota RAV4

1 Answer

Where is the water pump


Water Pump REMOVAL & INSTALLATION 5VZ-FE Engines Fig. 1: The water pump is located on the front of the engine block, behind the timing cover 93163p92.jpg
Fig. 2: Once the retainers are removed, pull the pump away from the block 93163p97.jpg
Fig. 3: Scrape any remaining gasket material from the block before installing the new pump 93163p98.jpg
Fig. 4: Water pump mounting bolt locations 93163p88.jpg
Fig. 5: Front view of the water pump and thermostat housing 93163p99.jpg
WARNING
This procedure requires the removal of the timing belt. This is an extensive procedure requiring precision work, particularly at assembly. For more information, refer to Timing Belt Removal and Installation. Do not attempt to remove the belt without consulting the procedure; extreme engine damage may occur. Fig. 6: Apply sealant to the areas shown 86823pi7.gif
Fig. 7: A and B bolt locations 86823pi8.gif
Fig. 8: Exploded view of the water pump arrangement — 5VZ-FE engine 93163g19.gif
  1. Drain the cooling system.
  2. Remove the timing belt. For additional information, please refer to the following topic(s): Timing Belt Removal and Installation.
  3. Remove the idler pulley.
  4. Remove the thermostat.
  5. Disconnect the oil cooler hose from the pump.
  6. Remove the seven bolts and the tension spring bracket and then remove the water pump. To install:
  7. Clean all parts well. It is good practice to carefully clean all threaded openings, especially those exposed to coolant to remove rust and scale so at assembly, an accurate torque reading is obtained. This is important since gasketless applications like this depend on even clamp loads from the fasteners to avoid distortion and leaks. Remove any old sealer (Toyota calls it packing) from the pump and mounting area of the engine. Keep oil off the mating areas.
  8. Apply Formed In Place Gasket (FIPG) sealer to the pump-to-block mating surface and then tighten the bolts marked A in the illustration to 13 ft. lbs. (18 Nm). Tighten those marked B to 14 ft. lbs. (20 Nm). NOTE: The parts must be installed within 5 minutes of application of the sealant. Otherwise you must remove and reapply the sealer.
  9. Connect the oil cooler hose.
  10. Install the thermostat with a new gasket.
  11. Install the idler pulley.
  12. Install the timing belt.
  13. Install the drive belts and adjust the tension.
  14. Refill the cooling system and check for leaks.
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump. To install:
  6. Clean the gasket mounting surfaces.
  7. Install the replacement water pump using a new gasket.
  8. Install the water pump pulley and fluid coupling with the fan.
  9. Install the removed engine drive belts.
  10. Fill the cooling system.
  11. Connect the negative battery cable. Start the engine and check for leaks.
  12. Bleed the cooling system.
1FZ-FE Engine Fig. 9: Exploded view of the water pump mounting on the 1FZ-FE engine 86823pk0.gif
Fig. 10: Detach the oil cooler hose from the clamp on the fan shroud 86823pk3.gif
prev.gif next.gif

Jul 13, 2010 | 1997 Toyota RAV4

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

1 Answer

Water pump


Hello drain the water from the radiator by removing the hose from the radiator to the water pump,after having taken out the hoses,then unscrew the bolts that hold the water pump.After having taken the pump,clean the surface where the pump is fitted on the engine.Now when putting,the new pump,put a clear layer of silicone gasket on the surface where the pump will fit to prevent leakage,now you screw the bolt to the same torque,then after put the hose back like it was before,fill your radiator ,do not put the cap now,because of an air lock in the water circuit,start the engine,you will see the water level lower,fill it to its level,then put the radiator cap.Hope that help you in changing the pump,good luck

Dec 26, 2009 | 2000 Nissan Maxima

2 Answers

97 toyota rav 4 dies at accel.


most likely its your fuel pump. when the rpm's start to drop just give the gas pedal a few pumps and you should be good.

Nov 17, 2008 | 1997 Toyota RAV4

Not finding what you are looking for?
2007 Toyota RAV4 Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...