Question about 2001 Hyundai Elantra

1 Answer

Connecting rod bearing( hyudai elantra 2001)

How much I have to tork the connecting rod bearing of a hyndai elentra 2001?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 104 Answers

32/33 Lb.ft for the connecting rod Bolts. For other units kindly use conveters

Posted on Jun 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is code P0120 for a 2001 hyudai elantra

The code is for a problem with the throttle position sensor circuit.
The sensor would need to be tested with a meter.

Sep 21, 2012 | 2001 Hyundai Elantra

1 Answer

2001 elentra front driver side axle removal instructions

take off wheel, pull both strut bolts,then push the strut to free it , undo tie rod end ( smack it with a hammer on the arm for the spindle a few times to get tie rod end out of the spindleand it will move side to side giving you room to pull the c.v. shaft out. then use a 32 or 36 mm socket to remove c.v. shaft bolt. hit the c.v. shaft a few time to free it from the hub assy. then get under the car and use a pry bar to remove the shaft from the transmission(you may lose a little ****** fluid). then just repete in reverse to install

Nov 30, 2011 | 2001 Hyundai Elantra

1 Answer

Hyudai elantra 2001 aut 35000 millas valor en mercado

Hi, please can you re-write the question in English so i can proffer a solution....

Jun 06, 2011 | 2001 Hyundai Elantra

1 Answer

I have a 2003 hyndai elentra an i had both 02 sensors replaced plus flex pipe and check engine light came back on with 02 sensor error

Try first to clean out the MAF sensors and the intake with tuner cleaner spray. Check also the the fuel regulator. Check also for holes and gapes from the air filter to the intake manifold. An error on the O2 sensor mean does not mean it is faulty. It may also be related to the air fuel mixture. Check also the wiring of the sensors (MAF and O2).

May 02, 2011 | Hyundai Motor 2003 Elantra

1 Answer

I have hyndai elantra 2001 automatic sometimes hesitant to start.

Sounds like a fuel pressure problem. Check/inspect your electrical connections to the fuel pump (power & ground). Also, connect a fuel pressure gauge to the fuel line at the fuel injector rail - leave it connected so if and when you have this problem again, you will be able to determine if the cause is fuel pressure/pump.

Sep 06, 2009 | 2001 Hyundai Elantra

1 Answer

Fuses for dome lights 2001 Hyndai Elantra

b-alarm 10a fuse located in engine compartment fuse box,fuse gives power to dome and map lights.

Jul 01, 2009 | 2001 Hyundai Elantra

1 Answer

How do i know why the check engine light is for on a 2001 elantra

take it to someone who has an obd 2 scanner tool to read the codes for you

Apr 02, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
2001 Hyundai Elantra Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8729 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides