Question about 2004 Dodge Ram

Open Question

Where is the thermostat located on a 2004 3500 dodge ram 5.9 turbo cummings diesel

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: removing speedometer 1992 dodge ram 250

I don't know if it's the same as my D150. But it's pretty simple:
1) remove about six screws from under the upper lip of the dash face bessal and one under the overhand above the radio.
2) carefully jimmy the bessal straight out. It has about four spring trim-clips that will release under pressure.
3) this exposes the speedometer instrument cluster. It is one big assembly (speedometer, fuel, temp and elctrical guages, etc) attahed with about six #2 phillips face screws. Remove these.
4) There are three back contections on the cluster: two electronic and one mechanical. Carefully start to pull the cluster out along the steering column until you see the shift indicator control line ( a small fishing-line with a hook on the end) attached to a small steel flang on the base of the steering column. This can be unhooked with your fingers or needle-nose pliers.
5) as you pull the cluster further out you can reach behind and unplug the two electronic connections. The round one simply pulls straight out. The last (rectangular) one has a pinch latch you need to compress to allow the plug to come out.
your finished!

Posted on Mar 11, 2009

Ad
  • 29 Answers

SOURCE: Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel

I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Posted on May 03, 2009

  • 66 Answers

SOURCE: I am looking for the I.A.T. Sensor location on my truck

If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Posted on May 27, 2009

  • 25 Answers

SOURCE: is ther more than one

dodge decided to do away with the fuse box that was located on the interior of the vehicle ( I also have a 2006 2500 diesel) there is on one fuse box located on the drivers side fender well under the hood this box is called a (TIPM TOTALLY INTEGRATED POWER MODULE) all power is distibuted through this box. this box is controlled by a computer with a softwear system.

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do you have a fuse and relay guide for a dodge ram 3500 dually (5.9L cummings turbo diesel


look under the hood there should be a box with all the fuses it will be under that box, if not open the driver side door, and it will be on the side panel to the left of the steering wheel

Jan 11, 2016 | Dodge Cars & Trucks

1 Answer

Is ther more than one fuse box on a dodge ram 2500. its a 2006 5.7 cummings diesel


dodge decided to do away with the fuse box that was located on the interior of the vehicle ( I also have a 2006 2500 diesel) there is on one fuse box located on the drivers side fender well under the hood this box is called a (TIPM TOTALLY INTEGRATED POWER MODULE) all power is distibuted through this box. this box is controlled by a computer with a softwear system.

Feb 10, 2011 | 2006 Dodge Ram 2500

1 Answer

Need instructions on how to replace water pump on 92 dodge ram 2500, 5.9 diesel turbo cummings


  1. Disconnect the negative battery cable.
  2. Drain the coolant.
  3. Use a 3 / 8 in. drive breaker bar to lift the belt tensioner and remove the belt.



0900c15280070771.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: Always install a new O-ring in the diesel water pump

  1. Remove the two water pump retaining bolts and remove the pump from the engine.
  2. Remove the O-ring from the pump groove.

To install:
  1. Clean the O-ring groove and install a new O-ring.
  2. Clean the pump mating surfaces and install the pump to the engine.
  3. Tighten the mounting bolts to 18 ft. lbs. (24 Nm). Fill the radiator with coolant.
  4. Install the drive belt.
  5. Connect the negative battery cable, run the vehicle until the thermostat opens, fill the radiator completely and check for leaks.
  6. Once the vehicle has cooled, recheck the coolant level.

Dec 24, 2010 | 2004 Dodge Ram 2500

1 Answer

How does a fan belt for a 2005 cummings diesel go diagram


Heres a belt diagram for a 2005 dodge ram 2500 series, with the5.9 diesel engine hope this helps.93aadb7.png

Apr 20, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

Changing fan belt in a 2006 dodge cummings


diagram should be under hood,, on top of radiator cover

Mar 13, 2010 | 2006 Dodge Ram 2500

1 Answer

I have a 06 dodge ram 3500 with Cummings diesel.


you have what is known as an open diff. or worn out clutch packs in a limited slip. most makers put in a open diff because its cheaper and handles better. if you did not pay for it on your invoice your stuck with stock unless you put it in your self.

Dec 23, 2009 | 2006 Dodge Ram 2500

1 Answer

How do you remove the flywheel when replacing the clutch


Take trans out, clutch out, and remove the flywheel bolts.

May 30, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

1999 dodge ram 3500 cummings turbo diesel will not start.


Diesel engines fire on compression alone (usually 400psi).The Truck may have air trapped in the fuel system.When you perform any fuel system repair on a diesel it is going to take alot of cranking to get the air out. You can take the breather loose and shoot a VERY small amount of starter fluid in the intake and it should start. Do not use starting fluid much as it can damage the engine. Good Luck.

May 06, 2009 | 1999 Dodge Ram

1 Answer

I am looking for the I.A.T. Sensor location on my truck


If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Apr 05, 2009 | 2004 Dodge Ram 3500 Truck

Not finding what you are looking for?
2004 Dodge Ram Logo

Related Topics:

368 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...