Question about 1989 Chevrolet S-10 Blazer

3 Answers

I have a 1989 s-10 pick up 2.5 4 cylinder it wont start on a daily basis one dayit will start and the next it wont. when it won,t start i can get it goin with starting fluid.it has good fuel pressure but the injector won't spray till it starts

Posted by on

  • normakaiser Jun 07, 2010

    replaced battery, battery cables,starter,injector

  • normakaiser Jun 10, 2010

    i have replaced the fuel injector (it only has 1) i have replaced the computer module, the fuel filter, the fuel pump the spark plugs the spark plug wires, , battery, battery cables, checked fuel pressure it is good, set timing, cleaned injector. any other suggestions?

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 312 Answers

I had the same trouble with same engine it was one I sold to a customer We were baffled until we checked the fuel pressure when starter was engaged and seen the pressure dropped a lot. It dropped far enough so it would not fire the injectors. If the battery had a full charge and I mean full charge it would start but when the customer left her cell phone on charge overnite it would not start. Check that out our pump was just weak enough that it needed a full 12 volts for it to push enough pressure during cranking to fire the injectors. Good Luck. Darrell S

Posted on Jun 10, 2010

Your fuel injectors will need to be cleaned out. The vehicle computer sends a signal for each injector. Check the ignition coil and ignition module with a multimeter, these two componants control the spark to the plugs for ignition.

Posted on Jun 07, 2010

  • Anonymous Jun 07, 2010

    Replace the fuel filter

  • normakaiser Jun 08, 2010

    i have replaced the fuel injector (it only has 1) i have replaced the computer module, the fuel filter, the fuel pump the spark plugs the spark plug wires, rotor button, battery any other suggestions?

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,059 Answers

Make sure you have a fully charged battery and I would run a can of injector cleaner through the gas tank.

Posted on Jun 05, 2010

  • normakaiser Jun 05, 2010

    i've put a new 900 cranking amp battery , new battery cables new srarter, cause i was thinking maybe it was drawing too much voltage

  • normakaiser Jun 06, 2010

    also replaced the injector but still no change

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low compression cylinder 2 and 4


A mechanic doesn't know why the motor
has low compression ?

Wouldn't you conclude that person has no
test equipment or doesn't know how to use it

Obviously you have bad valves or a failed head gasket,
if only two cylinders are an issue

Feb 26, 2014 | 2002 Chrysler PT Cruiser

1 Answer

2000 jeep wrangler wont start


If it won't crank, check clutch safety switch and cables for the starter.
If it cranks but won't start, you'll need to find out if it is ignition or fuel to know where to look next.

Jun 26, 2012 | 1994 Jeep Wrangler

1 Answer

Bolt wont unscrew


Welcome to the club! I get those on nearly a daily basis!

Jun 16, 2012 | Cars & Trucks

1 Answer

I have a 1991 toyota pick up that won't start. I have spark the and it seems as the truck wants to start but i don't think its geting fuel. Fuel preasure is good. what should i check next?


An injector pulse tester is called a "noid light". You plug it into the injector connector, and, cranking, it should flash, or blink. Try it on each injector connector.Buy them from any parts store. Blinking light means you are getting power to the injectors. The igniter tells the computer when to ground the injector signal, so it will operate and spray fuel into your cylinder. goodluck.

Oct 11, 2011 | 1989 Toyota Pickup SR5

3 Answers

My son has a 1996 Volvo 850 GLT Wagon and he needs the spark plug diagram. He changed the plugs, rotor, and distributor cap and the vehicle will not start. He did this work because the engine was running,...


Don't know your engine size so pick the correct one for your motor:


0ac2a3e.gif
2.3L 4-Cylinder Engines Firing Order: 1–3–4–2 Distributor Rotation: Clockwise


d674eac.gif
2.8L 6-Cylinder Engine Firing Order: 1–6–3–5–2–4 Distributor Rotation: Clockwise


6e9df21.gif
2.9L 6-Cylinder Engines Firing Order: 1–5–3–6–2–4 Distributorless Ignition


91ee348.gif
2.3L and 2.4L 5-Cylinder Engines Firing Order: 1–2–4–5–3 Distributor Rotation: Counterclockwise

Oct 12, 2009 | 1996 Volvo 850

1 Answer

Won`t start


My name is Ron ,sounds like you need to put a new pick up coil in distributor,and a module also,so you won`t have to go back in the distributor,If I can help roniecon@gmail.com

Jul 19, 2009 | 1991 Chevrolet K1500

1 Answer

Ignition lock cylinder wont come out. bought a new one to replace it, but cannot get the old one out. Any ideas? HELP!!!


under the steering weel, right below the lock cylinder there are three holes, two about the same size one smaller, the small hole is to pick the lock cylinder with a thin small screw driver i prefer philips.

1.- insert the key
2.- turn the key to on position (don't start the car)
3.- insert the screw driver until you touch the cylinder, find the locking ball, push, lock cylinder should move and pull the key with the lock cylinder
4.- install the new cylinder by pushing in.

Apr 16, 2009 | 1998 Ford Windstar

1 Answer

Car will not start


If I am right, the firing order is,1-3-4-2. With the dissy cap removed, have someone turn the engine over so you can see which way the rotor arm goes. Set the engine to TDC and the rotor arm should point to the No1 cylinder at the start of the firing order. If it rotor points away from the No 1 cylinder then slacken the dissy housing and move the diddy until the rotor ppoints to the No1 cylinder. Now pHT lead from the No1 spark plug to the No 1 possition on the dissy cap. The next lead goes on the next available possition on the dissy cap in the way of the rotation of the rotor then to the No3 spark plug carry on the same with 2 and 4 and that should solve your problem unless you have a different firing order.

Sep 21, 2008 | 1990 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...