Question about 2002 Kia Rio

1 Answer

Clutch releases on floor - 2002 Kia Rio

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

The clutch will probably need to be replaced. I would check the fluid level in the clutch master cylinder, also check the operation of the slave cylinder.

Posted on Jun 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal on floor


Check for broken clutch cable if equipped or clutch master cylinder low/empty of fluid indicating a worn clutch or hydraulic leak

Mar 10, 2016 | Cars & Trucks

1 Answer

How to bleed a clutch


Get a friend to help. Press clutch down to floor and hold, have your friend loosen the line at the slave cylinder, or clutch actuator under the car enough that fluid squirts out. Have him tighten the line back up. Release the clutch and press back to the floor again. Have your friend repeat the process as before. (loosen to let fluid squirt out, then tighten back up) Release the pedal. Repeat this process untill there are no air pockets left in the line. NOTE: if your clutch pedal fails to return to the top, simply pop it back up with your hand/foot, wait a few seconds, then depress to floor again for another bleeding.

Nov 19, 2013 | 2001 Ford Focus

1 Answer

Clutch pedal travel


Your pedal height may be adjustable by a stopper bolt at top of pedal. You would have to check the specification for your car. Most important that the pedal has about a half inch free travel before clutch begins to engage. You need that free play to ensure the release bearing (the throw-out bearing) is not touching the fingers on the pressure plate when not engaged. If it always is touching, it will be rolling around constantly and will go out prematurely.
Your new clutch will allow gear engagement sooner as the clutch pedal is released. I mean gears will engage just as pedal is lifting off from floor. You should notice that difference-the old clutch would have taken longer pedal travel from floor before releasing.

Apr 15, 2013 | Cars & Trucks

1 Answer

Clutch hit the floor


Something let go in the clutch release and that stalled the engine as you stopped. Go under the car and look for a broken clutch release rod or arm.

Oct 26, 2012 | 1990 Subaru Legacy

1 Answer

Clutch pedal staying down but there's plenty of fluid in resiviour


Probably bad clutch master cylinder and/or slave cylinder. I always replace both.

Oct 04, 2012 | Cars & Trucks

1 Answer

Clutch pedal snaps all the way to the floor


Your car has a hydraulically operated clutch release system, it has failed, see a local shop to repair it, cost is about $500.00

Sep 04, 2012 | Cars & Trucks

1 Answer

Clutch will not engage when it was engaging perfectly to begin with.


Your car has a hydraulic clutch release system, it is defective, either the master or slave cylinder is leaking or pulling in air and this causes the clutch pedal to go to the floor.

Aug 06, 2012 | Cars & Trucks

2 Answers

98 civic hatchback, clutch goes to floor and stays there. The clutch and brake system share a resevior for fluid. Fluid levels are good. Is there a cylinder for the clutch like the brake cylinder? Is it...


Yes ,there has to be a separate clutch slave cylinder,
as it used to be called
Can't use the brake master for both
If you look around the transaxle, you should be able
to follow a plastic or rubber line back to the slave cyl
It may be down low on firewall
You most likely will have to get those parts at a dealer,
as I recall, from years ago when i had a trans shop
Sorry I can't be exactly familiar with your exact set up

Aug 04, 2011 | 1998 Honda Civic

2 Answers

My clutch is sticking to the floor, but there is plenty of fluid and there does not appear to be a leak


you may need the clutch replaced if the clutch slave cylinder and master is working.

Jun 22, 2011 | 1988 Mazda B2200

1 Answer

Clutch sticking/not releasing/engaging


Is it sticking to the floor? releasing/engaging?

If its not releasing the clutch...[Car will try to move when starting with car in gear]
If so check the fluid. this is a hydraulic clutch,
If fluid is gone check for a leak or a bad Clutch Master Cylinder

If its not engaging then the Clutch maybe bad.

Nov 26, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
2002 Kia Rio Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...