Question about 1995 Ford Econoline

1 Answer

I am trying to change fuel filter on 1995 ford econoline f-350 It appered that the fuel lines were held on by push on retaining clips but after removing the retaining clips I still cannot seem to get the fuel lines to come off the filter. Do I need a special tool?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 80 Answers

Yes you do, The first clips you removed are the secondary clips. The lines have to be released from the inside. Heres the info.. Cobra :-)
Removal

  1. Open safety clip.

    I am trying to change fuel filter on 1995 ford - v9067a.gif

  1. Fit Tool T90T-9550-B (5/16 inch) or T90T-9550-C (3/8 inch) to coupling so that tool can enter female fitting.

    v9068a.gif

  1. Push the tool into female fitting to release the retaining fingers from the formed male tube end.
  1. Pull male anI am trying to change fuel filter on 1995 ford - v9069a.gifittings apart.

    v9069a.gif

  1. Remove the tool from the disconnected fitting.
  1. Inspect the fitting for any internal parts that may have been damaged. Fuel tube should be replaced if internal parts are damaged.

Posted on Jun 06, 2010

  • cobra777
    cobra777 Jun 06, 2010

    Heres the pic of how it looks.







×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change fuel filter on 1997 Ford 150


Things You'll Need

  • Drop pan
  • Socket set
  • Fuel line disconnect tool
  • New filter

  • 1Slide the drip pan under the driver side of the truck, below the driver door. Climb under with the socket set, fuel line disconnect tool and new filter.
  • 2Unbolt the fuel filter retaining strap with the socket set. The filter is located along the inboard side of the frame, below the driver seat. When in doubt, simply follow the fuel lines forward from the fuel tank until you locate the filter.
  • 3Disconnect the front fuel line from the fuel filter with the fuel line disconnect tool. The line flares out where the filter outlet enters it and a retaining clip holds it in place. You can unseat this clip with a pocket screwdriver or a pick, but it's not advisable, as the clip tends to break if pried on unevenly. hence why u need the tool. about ten buck
  • 4Pull the fuel line off the front of the fuel filter and then pull the filter out of the rear line and retaining strap. Put the old filter in the drip pan.
  • 5Slide the new filter into the retaining strap and plug the inlet into the rear fuel line. Make sure the arrow indicating flow direction points toward the engine. Connect the front fuel line, push the retaining clip back into place and bolt the retaining strap back to the frame.
  • 6Climb out, get in the truck and turn the ignition key to the run position. Wait for the fuel pump to stop running (this should be about 10 seconds) and start the truck.

Nov 18, 2011 | 1997 Ford F150 Regular Cab

1 Answer

Fuelfilter try to change fuelfilter and wont come


ou need a special tool to remove the fuel lines on your vehicle. Fortunately Ford had the wisdom to provide it to you. Here's how to do it.

Removal:
Warning: because of the combustion characteristics of gasoline, always use extreme care when removing and installing any fuel system component or personal injury or damage to the vehicle may occur.

  1. Perform the fuel pressure release procedure.
  2. Raise vehicle on hoist.
  3. Remove push connect fittings at both ends of the fuel filter. NOTE: To remove 5/16" push-connect fittings, use Fuel Line Removal Tool T90T-9550-B or tool supplied on vehicle. Tool is located 254 mm (10 in.) behind fuel filter. Place in glove compartment after use.
  4. Install new retainer clips in each connect fitting.
  5. Remove fuel filter by pulling fuel filter toward center line of vehicle and free from fuel filter bracket. NOTE: The flow arrow direction should be positioned forward and downward to make sure of proper fuel flow through replacement fuel filter.


78037814.gif


Installation:

  1. Install fuel filter in fuel filter bracket, ensuring proper direction of flow.
  2. Install push connect fittings at both ends of fuel filter.
  3. Lower vehicle.
  4. Start engine and inspect for leaks.


78037815.gif

Mar 25, 2011 | 1998 Ford Windstar

1 Answer

Where the fuel filter located on a 2002 Ford explorer


your fuel filter is well hid !! the fuel tank is on the passengers side of your explorer on the fuel filer is located on the front top of your fuel tank ! access to the filter is obtained by removing the heat shield at the front of the fuel tank, there are two bolts retaining the shield to the right frame rail and two bolts retaining the shield to the cross member. once the shield is removed you will see the filter,Be careful removing the fuel lines, the lines have locking clips that DO NOT remove from the lines !! and can be damage if you are not careful (which will result in complete line replacement if the ends are broken. the line clips are released by disengaging the top of the clip then folding the the edge over towards the side its attached to next push both side's in (towards center on top edge) then push clip down part way while pulling line loose .Good luck Thanks for using fix ya

Jan 20, 2011 | 2002 Ford Explorer

1 Answer

I have a 1995 Ford E-350 with a 5.8L engine.i am trying to replace the inline fuel filter. Your answer earlier about "plastic clips" is incorrect. Mine has steel spring clips that snap over the crimped on...


You will need a fuel line quick connect removal tool to release the inner clips holding the line in the filter.when you purchase the tool make sure you get the correct size for the line.

Jun 26, 2010 | Cars & Trucks

1 Answer

How to change a fuel filter on a 95 ford f-350 with a 460 engine


You will need to check inside the frame under the drivers door for the fuel filter. You will need a tool to remove the fuel lines. Remove clips from the fuel line holding the fuel filter (new ones supplied with new filter). Use the tool to insert into the fuel line to remove on both sides. Once lines are removed, remove fuel filter and replace with new ones. Be sure to put in new clips and attach lines. Good luck

8aa7deb.jpg0deefeb.jpg

May 29, 2010 | 1995 Ford F350

1 Answer

Remove a fuel filter from a 2001 ford econoline


Check in the frame rail on the driver side on the metal fuel line. Ford's been sticking the filter down there.
The filters come with a special tool to remove their special clips..

Apr 07, 2010 | 2001 Ford Econoline

2 Answers

How do I change the fuel filter on my 2000 Excursion? New filter has plastic clips


You need a small pocket screw driver and pinch the opposite end of the clamp to remove. Normally they come with new clips as the old ones break off. And if the filter has been on a long time the clips can actually wear out and can leak fuel if you don't replace them.you also have to remove the one or two mounting bolts holding it on.

Jan 28, 2010 | 2000 Ford Excursion

2 Answers

Uninstalling and installing fuel filter


Fuel line tool. Can be found at any auto parts store. There are muptiaple sizes, so if you get a single one, make sure it's for your vechile. However, most tools come with all proper sizes. Once you have the tool, you slip it on the line, with the long end, you'll see what i mean, towards the filter. Push in and twist, while doing so pull line and filter away from each other. Line should pop right out. There might be some metal clips on the filter and line to keep them connected as a precaution. Those have to be removed to get the tool in proper area. A little note for you, I've worked in auto shops and I hate chaning the ford fuel filters. They are a pain in the but. Plain and simple. See, dirt can get up in where the tool goes making it harder to get line apart. Do you plan on keeping your vechile for a while? If not, is it worth paying for the tool just for this one use? I'm just saying think it over.

Sep 24, 2008 | 2001 Ford Econoline

Not finding what you are looking for?
1995 Ford Econoline Logo

Related Topics:

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...