Question about 1994 Ford Probe

1 Answer

I am putting doors with electric windows on my 1994 ford Probe. Base model. Got the doors from a wrecked GT. Have put the passenger door on and window and electric locks do not work. How much am I going to have to rewire to get them to work. Yes the plug was installed in the door jamb, quite nicely. VIN: 1ZVLT20A4R5153275.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,019 Answers

It is not that much wiring, but the control unit.
There is a central radio receiver, alarm system, and door integration unit.
I believe it is under the dash and not under the hood.
But it depends on what you want to have it do?
You don't have the key to send the radio signals anyway, so that won't help. If you want one lock to lock all the door, that would not be that hard.
You would use an ohmmeter to figure out what connections were made when you locked the driver's door, at the drivers door wiring. For example, it probably momentarily closed contract across 2 wires.
So then if you ran power to one, rant the other to the other door lock solenoid, and then to ground, the locking of one would lock the other.
Unlocking would be similar, assuming you can figure out which wires are effected.

Posted on Jun 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install passenger window


most cars?
remove door cards, (the cover on inside of the door)
remove regulator bolts
remove reg. after detacting window base bracket.
remove, window .
some cars the upper trim can be removed, but that usually wrecks and costs 200 for a new set.
then pull window up past all missing seals.
if you remove the door card, you will see what needs to be done.
they pop off when pried, , start at bottom. (knobs first)

May 02, 2013 | 1995 Geo Prizm

1 Answer

I need two new doors the door locks and handels are broken and someone stole the interior door panel


have you tried to go to a junk yard or to a ford probe forum? I had a 89 Ford Probe GT and had the same issues.

Dec 22, 2010 | 1993 Ford Probe

1 Answer

How do i put the driverside window back on the track for a ford 2002 GT mustand 2 door?


pull door panel off to get to window now it depends if you have electric or manual windows

Nov 06, 2010 | 2002 Ford Mustang

1 Answer

Headlight doors won't stop opening and closeing


The headlight switch is called a multi-function switch. That is the problem, its going out, if you replace that, it will fix the problem, they run about $75 and are fairly easy to do yourself.

Apr 16, 2010 | 1994 Ford Probe

1 Answer

I have a 94 mustang gt. when the car was bought it had been wrecked on the driver side door. the window didn't work, it now has a new door but the window doen't work. I have hook the window motor up to a...


It's quite likely that in the wreck the wires got pinched and are broken inside the insulation. Bend the wire between your fingers and slide your hand along from the switch to the motor and you'll probably feel a spot where it bends easier than the rest of the wire. That would be where it is broken. Cut it and splice it. If you can't feel anything, put a jumper wire on them and that should do the trick. Hope this helps.

Jan 17, 2010 | 1994 Ford Mustang

1 Answer

1996 ford probe passenger electric window no longer works.


you blew the fuse for your radio.you cannot put a hot wire to a ground that is why the fuse blew.you could have broken a wire connector for the door,windows etc.the headlight switch wire harness is probably melted this happens a lot on Ford products,the head light draw so much heat they melt the wire harness plug that goes on the back of the headlight switch.

Jul 25, 2009 | 1996 Ford Probe

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

How do i remove the passenger window in a 1994 ford probe gt?


Door Glass and Regulator REMOVAL & INSTALLATION
  1. Lower the window glass and remove the inner handle cover, door lock knob (if necessary), the window regulator handle and the door trim panel. NOTE: On vehicles with power windows, disconnect the wiring couplings.
  2. Carefully peel off the door screen so that it can be reused.
  3. Replace the window regulator handle and position the door glass so that the door glass installation bolts can be removed from the service hole.
  4. Remove the door glass installation bolts.
  5. Remove the door glass. Remove the regulator installation bolts, and then remove the regulator through the service access hole. Remove the window motor mounting bolts and separate the motor from the regulator.
  6. Installation is the reverse of the removal procedure. If the vehicle is equipped with power windows, connect the leads of the motor to a battery and run the regulator to the down position before installing the motor. Cycle the window several times to make sure that everything is in good working order.
The door glass retaining bolts can be removed through the access hole


3838624.gif

Mar 20, 2009 | 1994 Ford Probe

1 Answer

1989 to 1990 Powered door conversion


about the only advice i can give is that i did the same thing with a 94 probe base and a 94 gt. i had to take the whole wiring harness out of the gt and put it in the base. It starts from the inside fuse block, goes to both doors, under the front seats, all the way to the fuel pump, abs, tail lights, and pretty much everything from the dash to the rear of the car. If you can get a whole harness, it should work.

Mar 09, 2009 | 1990 Ford Probe

1 Answer

Passenger side doorwon't open from inside the car


What has happened is the poorly designed clip that holds the pull bar to the handle has snapped causing the bar to fall out. Take the interior panel off of the inside of the door, using 2 pairs of pliers twist the end of the bar around and simply insert it in the hole it fell out of, I have had to do this to all of my doors and, unless you slam the door really hard it will stay put.

Sep 14, 2008 | 1994 Ford Escort

Not finding what you are looking for?
1994 Ford Probe Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...