Question about 1997 Ford Expedition

1 Answer

Need to replace the starter..where is it located

Need to replace the starter..where is it located and how easy is it to replace

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

It is on the passenger side, under the truck, mounted to the transmission. It's not too bad to replace, except for the top bolt for the starter, it's a bit difficult to get to.

Posted on Jun 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace starter


Replacing starter is not a difficult job.The vehicle needs to be lifted up on jack stands.The starter needs to be accessed from under the car. --------- You need to remove the air filter housing and intake, and the battery and tray if you want to make it easy on yourself. Remove those first, then remove the top starter bolt before you go under the car.

Accessing the top starter bolt,sometimes takes time. The top bolt comes from the transmission side on top.
-----------
Click this link below to see diagram showing location of top bolt:--- http://technoanswers.blogspot.com/2011/10/how-to-replace-starter-on-2000-mazda.html --------- This will help.Thanks.Helpmech.

Oct 07, 2011 | 2000 Mazda Protege

1 Answer

Need to replace the starter is it hard to replace????


Its not that hard. First of all disconnect the Negative battery,And All you need to do is locate the starter and locate the bolts that hold it usually 14 Mm bolts. take the wires off and label them where they go to make it easy for you to put them back again, put in a new starter in and sometimes you need to shake it little bit to make it slide in, and put back the wires and tighten them then start your car and good luck.

Dec 17, 2010 | 2001 Ford Taurus

1 Answer

My starter is going and some times it starts today it won't. I read if I hit it it may start but I can't locate. The starter to hit it. Where is the starter located?


I had a similar problem, hitting it may work some times but I think the contacts in the solenoid are worn out, replace the contacts, I managed to buy them at the local Auto shop, but not easy to find, or replace the starter.
Removing and replacing the starter is not so easy.
Hope this helps.
Graham

Nov 01, 2010 | 1991 Toyota Previa

1 Answer

Replacing a starter


Replacing the starter on a 96 Avalon is incredibly simple. I did it in the parking lot of a store. Just bring your ratchet set and you will be good to go. I took out the old starter, had a friend bring me to autozone and I bought a new one. Its easy to locate, easy to remove and easy to install.

Jul 12, 2010 | 1996 Toyota Avalon

3 Answers

Where is the starter located in a 1995 lebaron


starter is located on the drivers side near the radiator. the connections are a little difficult but the starter bolts are easy to get to and the starter is easy to replace. I replaced one in a parking garage. Took about 30 minutes

Dec 30, 2009 | 1995 Chrysler LeBaron

1 Answer

Starter


the starter is located under the air intake manifold connected to the transmission bell housing, easy to replace if you take off the manifold assembly, hope this helps and good luck

Nov 21, 2009 | 1998 Toyota Corolla

1 Answer

2002 mitsubishi galant,how to replace the starter


It's fairly easy, albeit a tight fit. Before you start, be sure to disconnect the battery. The starter is located between the firewall and the engine, underneath fuel injection assembly. Stick your hand in there and you should be able to feel how the starter is positioned. There are 2 or 3 bolts holding the starter and they're easy to remove. You need to disconnect the wire on the starter coil (the coil is located on top of the starter itself).
Now the fun part: removing the the starter itself. The way I did it is by wriggling it out the open space on the left side of the engine, hence the tight fit. Move any cables or wires that may get in the way for more room. (Important advice: Remember, patience is a virtue!)And there ya go! To install/re-install the starter just do the reverse. It's a lot easier to put it back in than removing it. Good luck!

Sep 28, 2009 | 2001 Mitsubishi Galant

1 Answer

I need to replace my starter in my 2000 Chevy Blazer. I need help please.


Unhook battery cables from battery locate starter on underside of engine block on the passenger side three bolts to take out replace starter and reverse procedure fairly easy job!! good luck.

Aug 05, 2009 | 2000 Chevrolet Blazer

1 Answer

94 toyota carolla starter clicks eventualy starts


You have two options: replace the starter (easiest, but most expensive), or replace the contacts (cheaper, but more work involved).
In any case, you have to remove the starter. Disconnect the battery BEFORE you start. Locate the starter and remove the wires going to it. The starter is held onto the transmission with 2 large bolts. Remove both, and slide the starter out.

If you want to change the contacts, observe the starter, locate a metal plate held on with 3 bolts. Remove the bolts and the plate. You will now see a plunger, and 2 copper colored contacts. Those are what needs to be replaced. Changing the contacts is easy, just do one at a time, and ensure that all insulators are installed properly on reassembly.

Jan 13, 2009 | 1994 Toyota Corolla

2 Answers

Starter for dodge caravan 2000


DISCONNECT THE BATTERY, JACK UP AND SUPPORT YOUR CARAVAN. LYING ON YOUR BACK LOCATE THE STARTER WHICH IS ATTACHED TO THE ENGINE THROUGH THE BELL HOUSING .THERE ARE TWO 15 MILIMETER BOLTS THAT HOLDS THE STARTER ON . AFTER BREAKING THE BOLTS A 15MM WRENCH WOULD BE USEFUL.

May 17, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
1997 Ford Expedition Logo

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...