Question about 2004 Ford F350

Open Question

2004 Ford F350 Crew rear seat headrest removal

2004 Ford F350 Crew Cab How to remove the rear seat headrest?

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1010 Answers

SOURCE: how to replace actuator on F350 V0

My right sliding door's lock doesn't function either. I took off the door panel and found that the lock mechanism was broken. Normally I would think this strange, as the lock mech is metal. But since this is a Plymouth product, I some how think it should be normal for something to break off without it ever getting a direct hit. I can only assume that my kids closing the door too hard might have had something to do with this. Anyway, the whole lock mech needs to be replaced, and I haven't even tried to see how much that will cost me. This Van has cost twice in repairs than what I paid new for it. (just kidding, but it sure feels like it). If you have an answer to this query

Posted on Jul 06, 2008

  • 5 Answers

SOURCE: Looking for keyless door code

Are you referring to the wireless remote or do you have the keypad access? Ford usually puts the keypad code on a decal inside the glove box. I believe it may be located in another area but can't remember off hand. The owners manual should tell you where to find it.

Posted on Jan 10, 2009

  • 1 Answer

SOURCE: Removal of headrest on 2005 Ford F150.

i have a 1989 lincoln town car i would to remove the headrest can you help me

Posted on Jan 11, 2009

  • 6 Answers

SOURCE: Removal of headrest on 2005 Ford F150.

The headrest has on obvious button to adjust the height and another button kinda hidden to remove the headrest. The black plastic ring at the base where the metal poles insert into the seat is where the two buttons. You probably noticed the obvious on that sticks out of the side of one of the rings. The other plastic ring contains a similar button that is not noticeable due to it being flush with the side of the plastic ring. Adjust the headrest to its highest position, then locate the "hidden" button on the other plastic ring and depress it while lifting on the headrest and it should come out.

Posted on Feb 22, 2009

  • 1 Answer

SOURCE: 2004 nissan frontier crew cab radio

the plastic around the gear shifter will pop up with a good pull, then turn it side ways to get over the shifter, then there are 2 screws the hold the bezel down around the radio and air vents, then just pull from the air vents it will pop off to reveil the screws to the radio

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove the valance where the windsheild sprayers are located on a 1997 Ford F350?

there are four phillips screws in the hood gap area, remove the wiper arms, and then it pulls out from the chrome (alloy) trim.

Sep 02, 2010 | 1997 Ford F350 Crew Cab

1 Answer


my Ford manual says the same thing...

"Behind the right Kick panel"

you should not have to remove anything to get to this and there should be a cutout in the trim panel where the switch is located

could it be someone removed it?
also check the drivers kick panel

Apr 11, 2010 | 1997 Ford F350 Crew Cab

1 Answer


Lift the headrest to it highest postion. Insert a thin stick parallel to the head rest bar (the side facing the rear of the vechicle) I used a thin paint stirring stick, a Slim Jim is ideal.
Once the stick is inserted (10" give or take) push the head rest down holding the stick steady, then pull the headrest back up and it will come off the seat.
Hope this helps.

Apr 03, 2010 | 2004 Ford Mustang

1 Answer

2004 F350 Ford 4x2 DRW Crew cab 6.0 V-8 Diesel; how to reset check engine / service engine light

easiest way is to disconnect batteries step on the brake pedal then reconnect

Dec 09, 2009 | 2004 Ford F350

1 Answer

How to install yoke on the rear diff on a ford f350

remove driveshaft from yoke by removing bolts and possition to side. Measure the preload on the on the pinion nut if you don't have the tool to do this mark the nut and make mark on yoke to later align nut when reinstalling. remove nut. some times a slide hammer is required to pull yoke out. At thi time pinion seal should also be replaced. istallation is the reverse tap yoke in install nut and align marks previously made then reinstall everything else

Oct 23, 2009 | 1997 Ford F350 Crew Cab

2 Answers

Need to move front passenger seat much further back

the only way to do this is to take the seat out remove it from the rails take the rails to a machine shop and have them weld on extensions for the seat to slide on. you will also have to remove the rear seat stop so it will go further back and have them make catches in the extension for the seat to catch onto.

Aug 28, 2009 | 2004 Ford F350

1 Answer

Ford F350 Crew Cab Power Window Problem

Did you check for power at the switches. Are you sure the fuses are ok. Sometimes the wires break because of opening the door. You will have to inspect the harness and maybe have to remove the door panel. Most likely its a driver door wiring issue or the fuse.

Aug 05, 2009 | 1997 Ford F350 Crew Cab

1 Answer

I cant remove 97 f350 fuel filter

i do not think there any oyher way . it a chore

Apr 05, 2009 | 1997 Ford F350 Crew Cab

1 Answer

How do I access the rear inlet fitting to change the fuel filter on a 1997 F350 crew cab with the 460 and dual tanks?

okay let me clarify the fuel filter if its on the frame will have a strap attaching it to the frame usually remove with a 10mm socket and an extension and rachet.on the ends of the filter you will either have a flare fitting(usually 14&16mm) wrench or a black cover with a white clip push hose toward filter pull out clip wiggle off.if its too hard for you to get to remove the shield other wise if your a contortionist it should be easy

Apr 05, 2009 | 1997 Ford F350 Crew Cab

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides