Question about 2006 GMC Sierra 1500 2WD

Open Question

Removing the starter on a 2006 gmc sierra 1/2 ton

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: Replace starter on 1992 GMC Sierra pickup truck

First thing unhook positive battery cable, unhook main cable on starter selanoid and small wire on selanoid (there may be 2 small wires) There may be a bracket on front of starter that has to be removed, and then the 2 main bolts that hold it to engine block and it should come out.

Posted on Feb 14, 2009

  • 34 Answers

SOURCE: Need to remove starter from 1990 GMC Sierra C1500

check cable at both ends make sure its tight.move it @ starter see if post on solenoid is loose.remove battery negative before taking out starter

Posted on Jun 20, 2009

  • 1 Answer

SOURCE: 2006 GMC Sierra 1500 cant

The safety clamp is seized. It is on the cable just above the cups that hold the tire rim up. My mechanic had to torch the cable to get it off. If you can release the tension on the cable (support the spare while lowering the crank you may be able to get the clamp to release. If not, cut the cable above the clamp and you will still have enough cable length to bolt the cup back on. The owner's manual details this procedure. ( GM must know it does not release properly)

Posted on Jan 31, 2009

  • 50 Answers

SOURCE: how do i remove the starter from my 97 gmc sierra

ok first undo the battery then undo the electric wires all of them then there are only 2 bolts both should have to hold the back nut while undoing them then just slide off

Posted on Oct 16, 2009

  • 400 Answers

SOURCE: looking for ignition switch in 93 gmc sierra

Tword the bottom of the steering colume. It will have a couple of connectors going to it and a couple of rods going to it from the igniton cylinder. IT is on top and not easy to get the bolts out of it. You will need to remove the close out pannel to even be able to see it.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear bearings on a 2006 GMC Sierra 1 ton dually?


very carefully get a repair manual this will help you step by step

Sep 29, 2014 | Cars & Trucks

1 Answer

Change out a Starter in 1995 GMC Truck 1/2 ton


shes easy , two bolts and two plug wires cant screw up , worst part is the room you have to work with , try get front of truck off the ground so you can manover

Oct 26, 2009 | 1995 GMC Sierra C1500

1 Answer

Looking for ignition switch in 93 gmc sierra


Tword the bottom of the steering colume. It will have a couple of connectors going to it and a couple of rods going to it from the igniton cylinder. IT is on top and not easy to get the bolts out of it. You will need to remove the close out pannel to even be able to see it.

Oct 20, 2009 | 1993 GMC Sierra K1500

1 Answer

I have a 1991 gmc 1/2 ton pick up and i need to remove the axle can you tell me how?


remove spider gears in the diff assemble which makes a clip available top remove then axle will slide out

Sep 27, 2009 | 1991 GMC Sierra

1 Answer

How to replace a starter on 1994 gmc sierra 1500 with a 350 engine


unhook the battery, there are 2 wires on the starter solenoid, 1 is a 5/16 nut and the other is a 9/16 nut remove those wires. this maybe easier to remove the heat shield first. next ther are two 9/16 bolts holding the starter in position, remove, and the starter will come out, about a 15min job

Sep 27, 2009 | 2000 GMC New Sierra 1500

2 Answers

Bad front wheelbearing 2006 gmc sierra 1/2 ton pickup


Not too bad. Just break down the Hub and pull it out. You might need a big socket. Go get a chilton's manual, it will help you if you don't understand it.

Mar 26, 2009 | 2006 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

514 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...