Question about 1993 Chevrolet K1500

1 Answer

Changed sparkplug wires but sounds like wires where set wrong whats the setting for wires

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 753 Answers

Firing order for chevy V8 is 1 8 4 3 6 5 7 2 going clockwise rotation of distributor.

Posted on Jun 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Real rough idle, looses power for a second when driving at speeds over 45 mph. also when accelerating from a standstill. I have replaced the sparkplugs, guaged at 0.031 ,spark plug wires, distributer...

Hi Spacey, Sounds as if you have an old model of the HiLux. Is it Carburetor or injection? If its carb I think that's where your problem will be. If there is leakage between the throttle body of the carb and the main body above it, there will be a flat spot when pulling away from start and possibly at higher revs. The easiest way of dealing with the problem is to replace the carburetor. Keep in mind that the most critical setting in any carb is the float level, if its not set correctly it will either flood or starve. Sounds as if you may have those measurements wrong. The settings are specific to the type of carb, if you need further help, tell me the type of unit fitted to your vehicle. Regards Johngee10

Jul 17, 2011 | 1987 Toyota Pickup

1 Answer

I change the engine on the car and it's bacfireing and hard to start with backfireing at all the time but it's runing it run fine

This sounds like a crossed sparkplug wire, start by making sure the firing order is correct, if theres a sparkplug wire in the wrong spot this would cause hard starting and the backfiring, so check the firing order first, i would of given you a firing order diagram but you forgot to list the year, make , model and the engine size. good luck and have a good day.

Mar 18, 2011 | Volvo XC70 Cars & Trucks

1 Answer

My quad wont start an its has petrol an i have just changed the spark plug

get a diagram online for the proper sparkplug wire locations and make sure they got put pack in the right firing order. Sometimes it is easy to accidently get them mixed up. Also I was acutally given the wrong sparkplugs from the autoparts store the other day. I went to find out the proper gap setting online and found out the plugs I had were not for my vehicle. Checking the gap on plugs is important before you put them in because sometimes they get dropped and the gap is wrong when you get them out of the box.

Jan 14, 2011 | Honda Accord Cars & Trucks

1 Answer

How do i change spark plugs in 1992 buick le sabre

To change the plugs, do one at a time so not to mix up the sparkplug wires, remove plug wire from a plug, use sparkplug socket to remove the sparkplug make sure to gap new plugs, ask parts store for the gap setting they will give it to you when plugs are bought, the plug gapper is about $2.00. and that about it, the rear plugs are a little harder to get to but the same way to remove, some buicks came with metal heat sheild over the sparkplug boot in the rear cylinders make sure to reuse, you will know if you have them they will slide right off old boot.

Aug 20, 2010 | 1992 Buick LeSabre

1 Answer

I need the Gap settings

the sparkplugs are shipped with the propper gap setting *DO NOT CHANGE IT"

if its been altered, place a penny in the gap, and thats the space it should be gapped.

Mar 04, 2010 | 1994 Mazda MX-3

1 Answer

1989 Dodge Omni Stalls out

A sparkplug wire may have been loosesed or disconnected or damaged.
If you can't find it then wait until late evening when it's dark.

Open hood and start the car. You will see the sparks from the damaged/loose sparkplug cable. Don't touch it while ignition is ON. It will shock you!

If you "disconnected" any sparkplug wires when you replaced the oil pump, then they were not put back in the proper firing order.

Hope this helps!

Sep 04, 2009 | 1989 Dodge Omni

1 Answer

03 ford taurus wont fire ,spins over,no fire

What you do is take either and old sparkplug from the car or pull one from the car and connect one of the sparkplug wires to it. Then with an insulated set of pliers hold the sparkplug so the electrode is grounded. Then have someone crank the car over. This is best done at night so you can see if there is a spark. During the day however you should be able to here a spark. If not probably a bad coil.

Jul 20, 2009 | 2003 Ford Taurus

1 Answer

Bogs down when taking off, then runs fine until i stop again.

it appeares that your vehicle has what we call a flat spot.if you changed the sparkplugs reasently the air gap setting might be incorrect.if not changed sparkplug can be worn replace.proper airgap setting 1.1mm

Jul 11, 2009 | 2001 Hyundai Sonata

Not finding what you are looking for?
1993 Chevrolet K1500 Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides