Question about 1994 Chevrolet C1500

2 Answers

It is a diesel manual tran,just clicks when trying to start.I just put a new battery in and still does the same thing!

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Do you only have 1 battery? This is showing me you have a 1994 half ton.
In 1994 you should have a 3/4 or 1 ton if it is a diesel.
And Chevy put 2 batteries.
Check your cables you need a full 12 volts to the starter. Did you try jumping a cross the starter solenoid? MAKE SURE IT IS IN NEUTRAL PARKING BRAKE IS SET & WHEELS ARE CHOCKED / BLOCKED. Will the truck pull or push start? Or do the wheels just lock up when you try?

Posted on Jun 05, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,033 Answers

Sounds to be the Starter or starter solenoid .

Posted on Jun 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Transmission wont shift low 2 second , alredy change trans


I came across this problem before in my case it turned out to be the TPS sensor. I also had a problem like this and it was the Park Natural switch. The ECM could only see park so it would not let the trans shift. These things are easy to check with a scan tool. Good Luck :-)

Sep 10, 2014 | 1999 Chevrolet Silverado 1500

2 Answers

INSTALLED TRANS 700R4 RAN GOOD ALL GEARS SHIFTING PARKED CAR 4 A FEW MIN HAD HARD TIME STARTING FINELY STARTED NOW WONT GET NO GEARS EVEN REVERS ITS LIKE ITS IN NEUTRAL PUT BRAN NEW TORKCONVERDER ...


Sounds like a pump problem.Did you install the new torque converter after you started having problems or before?Did you bolt the converter to the engine and then install transmission or did you install transmission with converter in it?

Apr 03, 2011 | Buick Roadmaster Cars & Trucks

1 Answer

Tried to start my 2003 escalade this morning and it would only click. I replaced my battery and still nothing. after a couple of min. i tried agin and it started, this eve it is doing the same thing. just...


Yes - your problem is in your starter - specifically the armature and / or brushes. The starter is located on the passenger side of the vehicle, mounted to the front of the transmission and back of the motor. The starter's armature kicks out and connects with the Ring gear ( automatic trans) or flywheel ( manual trans) and turns the flywheel ? gear to engage the engine. The clicking indicates the solenoid is completing the circuit but the armature is not engaging the gear.The positive battery cable goes directly to the solenoid which is mounted to the starter and the positive cable MUST be removed prior to removing the starter. The armature and related brushes can be replaced instead of buying a new or rebuilt starter / solenoid assembly but should be done by a qualified professional as it can be done wrong and cause serious damage to the ring gear or flywheel.
Hope this helps and please rate my solution!!

Nov 26, 2010 | 2003 Cadillac Escalade

2 Answers

Need steps to start taking transmission out to


drain fluid, disconnect battery neg., remove shifter assem from top, remove driveshaft, support trans and remove crossmember, remove trans housing bolts, remove starter, remove trans. This is basic removal. Be very carefull to suport properly!

Jun 17, 2010 | 1991 Mercury Capri

1 Answer

I try to start my 1988 Jeep YJ (maunal trans) and I just hear a "click, click" sound. Jump started it and it was running, but I stalled it and the same thing, she wouldn't turn over...just heard the click...


First thing to check is the battery on jeep. If the battery is low on power or dead,charge the battery or replace it with a new battery. It sounds like you are not getting enough voltage to the starter to turn it over and start the jeep. Once you get the jeep started use a volt meter to check the voltage at the battery. The alternator should be putting out 14 to 15 volts to the battery. Check the battery cables at the battery,clean and tighten if need be. If the alternator is not putting out the voltage as i described then replace it. Make sure the radio and a/c is turned off in jeep before you run your test. Hope this will help.

May 19, 2010 | Cars & Trucks

1 Answer

2002 S10 4 cyl 5 speed manual trans. Truck will not start, no power to starter, or starter relay, when turning key odometer readout goes blank in run position, and fuel gage appears to not power up aswell....


could be the security system. this same thing happened to my grandmothers s-10. she took it to dealer and sure enough thats where the problem lay. i would start there

Aug 01, 2009 | 2002 Chevrolet S-10

1 Answer

2001 dodge ram 2500 diesel with 6spd manual trans. showing fault codes p1698 , p0237 & p0562. the truck will crank but not start. it has two new battery & map sensor.


p0562 is System voltage low
p0237 is Turbo/supercharger boost sensor A circuit low

cannot find a code p1698 but did find a p0698
p0698 is Accelerator pedal position sensor supply voltage to low

Apr 13, 2009 | 2001 Dodge Ram 2500 Truck

7 Answers

2002 dodge ram 2500 diesel truck shifts in and out of gear around 40 to 50 miles per hour


When your truck is shifting like you mentioned you need to check the battery cables. Better yet just replace the cables. Even a small amount of corrosion can cause a break down in the flow of current to the trans computer and cause erratic shifting. New cables should fix you right up. If this does not take care you need to start looking into "noise" from the alternator wire or other electrical interferrence. Another possible solution is to install a Hapi Box which clears interferrence in the wire from the TPS to the trans computer. It worked on my '02 until the cables corroded. I stripped back about 6" and found a mess in there. Good luck. (oh, Dodge will seel you a new trans to fix this problem. Be ware.)

Sep 15, 2008 | 1999 Dodge Ram 2500 4WD

2 Answers

I started my truck to move it out of the way and when i tried to turn off the engine it didn't turn off. how do i turn off a diesel without the key doing it for me?


Hi there,

Be careful doing this. You're going to try and stall the engine.

Manual Trans:
  • Put it in the highest gear
  • Hold the brake down
  • Pop the clutch
Auto Trans:
  • Press the brake
  • Put it in gear
  • Hold the brake and hit the gas
Hope this helps,

Mike

Jul 29, 2008 | 1983 Chevrolet Blazer

Not finding what you are looking for?
1994 Chevrolet C1500 Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...