Question about 2000 Ford Windstar

1 Answer

After a long run, with the temp gauge at half ( not hot9 . After stop running the motor, the coolant on reservoir star to boil , the relief valve on the reservoirs deposit open it . I change the termostat, hoses, apparently the motor doesnt et hot, ¿What can be going on)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 1,024 Answers

Check your radiator cap seal for damage, because it can let the coolant to enter the reservoir at low pressure

Posted on Jun 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

OVERFLOW IS BOILING


If the thermostat is not opening, the engine will keep getting hotter as you drive. You could be low on coolant and have air pockets in the system which would cause the temp gauge to not be accurate. Is the radiator fan coming on when the tank is boiling ?

Jul 29, 2013 | 2001 Chrysler Concorde

Tip

Vehicle overheating tips


If your vehicle engine coolant temperature gauge indicates overheating, if you experience a loss of power,or if you hear a loud knocking or pinging noise, the engine has probably overheated. You should follow this procedure............

Pull safe off the road, stop the vehicle and turn on our emergency flasher. Put the transmission in "P" (automatic) or neutral (manual) and apply the parking brake. Turn off the air conditioning if it is being used.

If coolant or steam is boiling out of the radiator or reservoir, stop the engine. Wait until the steam subsides before opening the hood. If there is no coolant boiling over the steam, leave the engine running. CAUTION: To avoid personal injury, keep the hood closed until there is not steam. Escaping steam or coolant is a sign of very hing pressure.

Visually check to see if the engine drive belt (fan belt) is broken or loose. Lock for obvious coolant leaks from the radiator, hoses, and under the vehicle. However, note that water draining from the air conditioning is normal if it has been used. CAUTION: When the engine is running, keep hands and clothing away from the moving fan engine drive belt.

If the engine drive belt is broken or the coolant is leaking, stop the engine immediately and call your mechanic of assistance.

If the engine drive belt is okay and there are no obvious leaks, you may help the engine cool down more quickly by running it at about 1500 rpm for a few minutes with the accelerator pedal lightly depressed.

Check the coolant reservoir. If it is dry, add coolant to the reservoir while the engine is running. Fill it about half full. CAUTION:Do not attempt to remove the radiator cap when the radiator are hot. Serious injury could result from scalding hot fluid and steam blown out under pressure.

After the engine coolant temperature has cooled to normal, again check the coolant level in the reservoir. If necessary, bring it up to half full again. Serious coolant loos indicates a leak in the system. You should have it checked as soon as possible at your mechanic's workshop.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

2 Answers

2005 sentra 1.8 no heat... checked level.. changed termostat.. blew outlines.. took lines off heater core blew thru them nothing came out but water we used. control on dash from defroster to blowing on...


Hi, the likely problem is a bubble forming in the system, possibly due to a head gasket failure.

Try stopping on a steep incline--does the heater stay warm? If yes, what you have is an air bubble that hangs at the heater hose until pressure from the water pump blows thru it as the engine speeds up. Park on an incline, open the radiator cap, run the engine until the thermostat is open, turn the heater on, crack open any/all bleed ports to release any trapped air, and fill the radiator to the neck. Wait until the level stops dropping and make sure bubbles don't continue to come up. If they do, you may have a blown head gasket that will keep forming these bubbles until you change the gasket.

Jan 11, 2011 | 2005 Nissan Sentra

2 Answers

While driving in 100+ degree heat, my van died.


SOUND LIKE COOLANT FAN NOT COMING ON.WHEN YOU ARE IN CITY.YOUR ENGINE RADIATOR NOT GETTING MUCH AIR FLOW IN THE CITY.BECAUSE YOU STOP AND GO ALOT.DUE TO A LOT OF STOP LIGHTS.CHECK COOLANT FAN RELAY AND FUSE.IF BOTH GOOD.COOLANT TEMPERATURE SENSOR SENSOR.IF ALL IS GOOD HOT WIRE COOLANT FAN TO SEE IF IT RUNS.IF NO FAN MOTOR BAD.IF YES FAN MOTOR RUNS WIRE CONNECTOR IS OPEN OR DAMAGED.

Aug 02, 2010 | 1993 Dodge Caravan

1 Answer

When idoling or driving car coolant starts boiling over at resevoir.I changed thermostat but did not help.when it boils over,temp is not even half way on gauge


Hi!

Your coolant temp sensor may be defective, check wiring also, if this senor doesn't send the signal the Cooling Fan won't kick in. Fan will come on when temp reaches half way on gauge.

Good Luck!!

Jul 30, 2010 | Ford Taurus Cars & Trucks

2 Answers

The cooling fans wont kick in and its boiling


The most common overheating problem with the Northstar engine is a blocked purge line. It's job is to purge air out of the cooling system.
If the purge line is blocked you may have an air lock preventing coolant flow.
There is a small diameter hose coming from near the top of the coolant tank,this is the purge line.
With the engine idling,pull the purge line from the tank,if there is no coolant flow from this small hose,it is blocked and this will cause overheating.If the hose is clear, check for blockage at the nipple on the tank.

Air locks in the Northstar engine shouldn't be a problem as the system is self purging, providing all the hoses are clear.

Check the coolant level in the tank,it should be half way when cold.
There is no cap on the radiator as it is a fully pressurized system.

The expansion tank is the only means by which to add coolant to the Northstar engine.

Check to see if your fans are working by switching on the air con,they should run all the time.

With the air con off,the fans won't come on until the temp hits around 225 degrees.

Also, if it's boiling over, the cap on the expansion tank may not be holding pressure and therefore needs replacing.....a new cap only costs a few dollars so it is worth replacing to see if this solves your problem.

Oct 09, 2009 | 1998 Cadillac Seville

1 Answer

2001 dodge stratus engine temperature gauge spikes occasionally


Look for a loose connection to the temperature sender unit on the motor.
If all connections OK, you may need a new temp sender unit.

Jul 28, 2009 | 2002 Dodge Stratus

2 Answers

Temp gauge was running at top end i changed


Is your coolant actually boiling? Is so, you may need a new water pump.

Jul 12, 2009 | 1997 Ford Contour

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...