Question about 1994 Dodge Dakota Club Cab

1 Answer

I need to bleed my clutch - 1994 Dodge Dakota Club Cab

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

You'll need to pump the pedal a few times and hold it down, while someone opens the bleeder screw on the slave cylinder, allow the air and fluid to release, close the bleeder and repeat until you just have fluid coming out of the bleeder. Make sure you check the fluid level as you go.

Posted on Jun 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed clutch cylinder for Nissan Sandra 2010


bleed clutch cylinder Robinny, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Bleeding clutch
Clutch bleed how to
Nissan Altima 2007 2012 Service Manual Clutch fluid On vehicle maintenance...
Help clutch bleeding Fail

Jul 19, 2016 | Nissan Cars & Trucks

1 Answer

Is it true that u need to bleed a clutch on a mits mirage 2001 car?


If you have replaced the clutch master cylinder or slave cylinder,then you do need to bleed,here's a link on how to bleed your clutch. Repair Guides Clutch Hydraulic System AutoZone com

Oct 05, 2015 | Cars & Trucks

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

What does it mean when the clutch petal goes all the way to the floor in my 2003 suzuki aerio


Your clutch fluid reservoir may need brake fluid-yes, it uses brake fluid as a hydraulic fluid. Check reservoir on the firewall. It will sit beside the brake master cylinder. The reservoir sits atop the clutch master cylinder.
If it was dry, the clutch may need bleeding down at the slave cylinder on the transmission housing-where the clutch fork sticks out of the transaxle.. Open the bleed valve on the slave cylinder, and have someone slowly press clutch down. Keep bleeding until a steady stream of fluid comes out when clutch is pressed. Then close bleed valve, check clutch operation-pedal should have some pressure on it now.

Dec 10, 2012 | Cars & Trucks

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

Can't get clutch to bleed on 1996 s 10 we have bleed bleed and bleed


Hi if you have done the following to bleed the clutch.
1 open bleed screw
2 push pedal to floor and keep on floor
3 do bleed screw up
4 lift pedal
5 undo bleed screw
6 push pedal to floor
7 do bleed screw up
8 lift pedal up
you need to repeat this a few times but making sure the fluid level dont drop below the lowest level else you will get air in the system.

right now if you have done the above properly and you still either get the pedal going to the floor and staying their or you have no pedal at all then this points to their being a fault with either the clutch master cylinder or clutch slave cylinder, now in most cases the one that fails is the master cylinder this is the one that is connected to the clutch pedal now its usually this one that fails and causes the pedal to go to the floor or have no clutch.

but it could also be the slave so bare this in mind, if the pedal comes back up after pushing it down then the chances are its the slave at fault and this is the one on the gearbox that operates the clutch arm.

let me know how you get on or if you need further assistance ok

plz rate this solution as i have a whole page of unrated posts, thanks

Dec 01, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

New clutch in 2010 but still can't shift properly; sticks between **** changes


you clutch needs bled better, i'm currently going through this now. If bleed your clutch hydrolics, and after a few days it starts sticking again, you will need a new clutch master cylinder and slaves cylinder. About $70 at autozone. Make sure when you bleed it you get NO AIR not even little bubbles coming out of the bleeder. Bleeding the cluch is much more difficult that bleeding the brakes.

Nov 05, 2010 | 1983 Mazda RX-7

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

2 Answers

Clutch bleeding


Try opening bleeder screw on slave cylinder and let it GRAVITY BLEED, just open clutch mater and fill with fluid and then open slave cylinder bleeder screw and let it gravity bleed( run out by itself) When it does close bleeder screw and you should get pressure.(make sure master doesn't run out of fluid during this preocess).If pedal not good enough bleed as usual. PUMP PEDAL ABOUT 6 time then hold down to the floor using wrench open slave bleed screw and close back up with pedal still being held DOWN. Repeat until fluid comes out with out air.However if all this doesn't work, YOU WILL NEED TO REPLACE CLUTCH MATER CYLINDER. Conatct if you need more help and Good Luck. Thanks for using FIX YA

Jan 12, 2009 | 2001 Honda Civic

Not finding what you are looking for?
1994 Dodge Dakota Club Cab Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...