Question about 1987 Toyota Pickup

1 Answer

Timing chain is loose how do I replace or tighten

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 125 Answers

You need to pull out the timing cover. 4-6 hours of work. Here is the step to remove the Cover, then you need to remove the Sprockets.
timing chain is loose how do I replace or tighten - moz-screenshot.pngmoz-screenshot-1.png

  1. Remove the oil pan.
  2. Remove the power steering belt if so equipped.
  3. Remove the air conditioning belt, compressor and bracket if so equipped.
  4. Remove the fan clutch (fluid coupling), with the fan and water pump pulley.
  5. Matchmark and remove the crankshaft pulley(s). This bolt will be very tight. Use the counter-holding bar, properly installed, to hold the crankshaft while loosening the bolt. Use the pulley extractor or gear puller to remove the pulley from the shaft.
  6. Remove the water bypass pipe.
  7. Remove the fan belt adjusting bar. If necessary, remove the lower power steering bracket for access.
  8. Disconnect the heater water outlet pipe.
  9. Unbolt the timing chain cover assembly. Be careful to loosen only the correct bolts.

To install:
  1. Install new gaskets over the dowels on the timing chain cover. Slide the cover assembly over the dowels and pump spline. Insert the retaining bolts and tighten them. Tighten the 8mm bolts to 9 ft. lbs. (13 Nm) and the 10mm bolts to 29 ft. lbs. (39 Nm).
  2. Temporarily install the adjusting bar to the alternator. Install the adjusting bar to the chain cover and tighten the bolts to 9 ft. lbs. (13 Nm).
  3. Install the heater water outlet pipe.
  4. Install the water bypass pipe.
  5. Install the crankshaft pulley and bolt. Use the counter-holding tool to hold the pulley and tighten the bolt to 116 ft. lbs. (157 Nm). If equipped with air conditioning, install the second crankshaft pulley.
  6. Install the water pump pulley and fluid coupling with the fan.
  7. Adjust the tension on the drive belts.
  8. Install the air conditioning compressor bracket, compressor and belt if they were removed.
  9. Install the power steering belt and adjust it.
  10. Attach the oil pan.
  11. Install the radiator.

Posted on Jun 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I put a water pump on 2.4 grand am


There are a lot of steps, and you need to take your time. You will need access to a lift or jack stand, and make sure you keep the work area clean and organised, taking photos of the timing system will make your life easier when it comes to re-timing the engine.

Water Pump Replacement (2.4L)
Removal Procedure
  1. Drain the coolant. Recover the coolant. Refer to Cooling System Draining and Filling.
  2. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement in Engine Exhaust.
  3. Remove the coolant intake pipe. Refer to Engine Coolant Inlet Pipe Replacement in Engine Cooling.
  4. Lower the vehicle.
  5. Disconnect the heater hose quick connect from the heater outlet pipe.
  6. Remove the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4L. (see below procedure)
  7. Remove the water pump cover-to-cylinder block bolts.
  8. Remove water pump pipe to cylinder block bolt.
  9. Remove the 3?water pump-to-timing chain housing nuts.
  10. Remove the water pump and cover assembly.
  11. Remove the water pump cover-to-coolant pump assembly bolts.
  12. Clean all sealing surfaces.
Installation Procedure
    Important: Before you install the coolant pump, read the entire procedure. Follow the tightening sequences in order to avoid part damage and to provide proper sealing.

  1. Install the pump cover bolts. Hand tighten the bolts.
  2. Install water pump cover assembly.
  3. Install the cover-to-block bolts. Hand tighten the bolts.
  4. Install the coolant pump-to-timing chain housing nuts. Hand tighten the nuts.
  5. Notice: Refer to Fastener Notice in Cautions and Notices.
  6. Torque in sequence as follows:
    1. Tighten the water pump-to-timing chain housing nuts.
      Tighten
      Tighten water pump to timing chain housing nuts to 26?Y (19?lb?ft).
    2. Tighten the pump cover-to-pump assembly bolts.
      Tighten
      Tighten the water pump cove to water pump bolts to 14?Y (124?lb?in).
    3. Tighten the coolant pump cover-to-engine block bolts. Tighten the bottom bolt first.
      Tighten
      Tighten water pump to engine block bolts to 26?Y (19?lb?ft).
  7. Install heater hose to pipe on water pump.
  8. Install the exhaust manifold and install new gaskets. Refer to Exhaust Manifold Replacement in Engine Exhaust.
  9. Install oil level indicator tube and indicator. Refer to Oil Level Indicator Tube Replacement in Engine Mechanical-2.4L.
  10. Connect the brake vacuum pipe to the cam housing.
  11. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  12. Install catalytic converter to to manifold. Refer to Catalytic Converter Replacement in Engine Exhaust.
  13. Install the coolant inlet pipe. Refer to Engine Coolant Inlet Pipe Replacement.
  14. Install the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4L.
  15. Lower the vehicle.
  16. Connect the oxygen sensor connector.
  17. Fill cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  18. Inspect the system for leaks.
Camshaft Timing Chain, Sprocket, and Tensioner Replacement
Removal Procedure
    Caution: Refer to Battery Disconnect Caution in Cautions and Notices.
    Notice: The timing chain on the LD9 (VIN T) Twin Cam Engine is not to be replaced with the timing chain from any other model year. The timing sprockets are different on the Twin Cam engine and the shape of the links matches the sprockets. Engine damage may result if the wrong timing chain is used. The timing chain and the crankshaft sprocket must be marked so that they are reinstalled in the same side facing out at the time of reassembly.
  1. Disconnect the negative battery cable.
  2. Remove the engine front cover. Refer to Engine Front Cover Replacement.
  3. Rotate the crankshaft clockwise (as viewed from the front of the engine, normal rotation) until the camshaft sprocket timing dowel pin holes align with the holes in the timing chain housing.
  4. Set the crankshaft sprocket keyway pointing upwards. Align with the centerline of the cylinder bores. This is the timed position.
  5. Remove the timing chain guides.
  6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  7. Ensure that all of the slack in the timing chain is above the tensioner assembly.
  8. Remove the timing chain tensioner bolts and the tensioner.
  9. Remove the tensioner shoe. Use a small locking ring plier in order to engage the hole in the locking tab and remove the shoe from the stud.
  10. Notice: Do not attempt to pry the sprocket off the camshaft or damage to the sprocket or chain housing could occur.
    Important: Mark the timing chain and the crankshaft sprocket prior to removal. If the chain or the crankshaft sprocket is installed with the wear pattern in the opposite direction, noise and increased wear may occur.
  11. Mark the crankshaft sprocket and the timing chain outer surface.
  12. Remove the timing chain.
  13. Lower the vehicle.
  14. Holding the intake camshaft sprocket with J 39579, remove the sprocket bolt and washer.
  15. Remove the washer from the bolt and rethread the bolt back into the camshaft.
  16. Using a 3-jaw puller and the relief holes in the sprocket, remove the intake camshaft sprocket.
  17. Repeat this procedure for the exhaust camshaft sprocket.
  18. Clean the old sealant from the bolt with a wire brush.
  19. Clean the threaded hole in the camshaft with a round nylon bristle brush.
  20. Inspect the parts for wear. Replace the parts as necessary.Some scoring of the timing chain shoe and the guides is normal.
  21. Replace the timing chain shoe or guides if the scoring exceeds 1.12?mm (45?in).
Installation Procedure


  1. Use Adhesive/Sealant Compound GM?P/N?12345493 or equivalent on the camshaft sprocket bolt. Install the intake and exhaust camshaft sprockets onto the camshafts with the marked surface showing.Notice: Refer to Fastener Notice in Cautions and Notices.
  2. Install the retaining bolts and washers to the intake and exhaust camshaft sprockets.
  3. Tighten
    Tighten the bolts to 70?Y (52?lb?ft) while holding the sprockets with the J 39579.
  4. Install the J 36800 through the holes in the camshaft sprockets into the holes in the timing chain housing. This will position the camshaft for correct timing.
  5. If the camshafts are out of position (you must rotate the camshaft more than 1/8?turn in order to install the alignment dowel pins), use the following procedure:
    1. Rotate the crankshaft 90?degrees clockwise off of the TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft counter clockwise back to the top dead center.

  6. Notice: Do not rotate the crankshaft clockwise to TDC. Valve or piston damage could occur.
    Important: The side of the timing chain that was marked during removal must be showing when the chain is installed.
  7. Install the timing chain over the exhaust camshaft sprocket, around the coolant pump, and around the crankshaft sprocket.
    1. Remove the alignment dowel pin from the intake camshaft.
    2. Using the J 39579, rotate the intake camshaft sprocket counterclockwise enough in order to slide the timing chain over the intake camshaft sprocket.
    3. Release the J 39579. The length of the chain between the 2?camshaft sprockets will tighten.
    4. If properly timed the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated.
  8. Leave the alignment dowel pins installed.
  9. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  10. The timing marks on the crankshaft and on the cylinder block should be aligned when the slack is removed from the chain linking the intake camshaft sprocket and the crankshaft sprocket. If the marks are not aligned, move the chain one tooth forward or rearward, remove the slack and re-examine the marks.

  11. Important: Use the following steps in order to reset the timing chain tensioner assembly to the zero position.
  12. Reset the timing chain tensioner assembly.
    1. Insert the tensioner plunger assembly into the tensioner housing.
    2. With the tensioner plunger fully extended, turn the complete assembly upside down on a bench or other flat surface.
    3. With the plunger face against the workbench, press firmly on the bottom of the tensioner housing.
    4. Compress the plunger until the plunger is seated flush in the tensioner.

  13. Check the plunger to make sure the plunger is out of the cylinder at the correct dimension. The correct dimension for the plunger to extend out of the cylinder is 1.7?mm (0.07?in) maximum.

  14. Loosely install the tensioner assembly and bolts to the timing chain housing.
  15. Install the timing chain tensioner shoe on the stud.
  16. Apply hand pressure to the timing chain tensioner shoe until the locking tab seats in the groove in the stud.
  17. Tighten the timing chain tensioner bolts. Do Not overtighten.
    Tighten
    Tighten the bolts to 10?Y (89?lb?in).


  18. Important: If the timing chain tensioner is not released from the installation position, engine damage will occur when the engine is started.
  19. Release the timing chain tensioner plunger.
    1. Using a flat blade screwdriver, cotter pin remover, or similar tool, press firmly against the face of the timing chain tensioner plunger.
    2. Important: If the timing chain tensioner cannot be depressed, the plunger is not properly reset and the procedure for resetting the timing chain tensioner should be repeated.
    3. Depress the timing chain tensioner plunger until the plunger is bottomed out in the bore of the timing chain tensioner.
    4. Release the tensioner plunger. the plunger should press firmly against the back of the timing chain tensioner shoe.
  20. Remove J 36800 from the camshaft sprockets.
  21. Rotate the crankshaft clockwise 2?full rotations. Align the crankshaft keyway with the mark on the cylinder block, and reinstall the alignment dowel pins. The pins should slide in easily if the engine is timed correctly.

  22. Install the timing chain guides.
  23. Install the engine front cover. Refer to Engine Front Cover Replacement.
  24. Connect the negative battery cable.
    Tighten
    Tighten the bolt to 16?Y (12?lb?ft).

Jul 02, 2016 | Cars & Trucks

1 Answer

Would like to have torque specs chart please?


Hi there, the following information are for a 2004 Grand Am 2.2L, I hope it helps:

--------------------------------------------------------------------------
Timing Chain, Sprockets, and/or Tensioner Replacement
--------------------------------------------------------------------------
Tighten the chain guide bolts to 10 N·m (89 lb in).
Tighten the chain tensioner bolts to 10 N·m (89 lb in).
Tighten the oil nozzle bolt to 10 N·m (89 lb in).
Timing chain tensioner guide bolt to 10 N·m (89 lb in).
Timing chain bolts to 10 N·m (89 lb in).
Chain guide plug to 90 N·m (66 lb ft).
Timing chain upper guide bolts to 10 N·m (89 lb in).
Timing chain tensioner to 75 N·m (55 lb ft).
Camshaft bolts to 85 N·m (63 lb ft) plus 30 degrees.
-------------------------------------------------------------------------
Intake Manifold Replacement
-------------------------------------------------------------------------
Manifold Nuts and Bolts: 10 N·m (89 lb in).

Aug 30, 2014 | 2004 Pontiac Grand Am

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off


Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.
  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
117016938

  1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Remove the primary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installation.
  1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
117016941

  1. Lower the primary chain with left side sprocket through the left cylinder head opening.
NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
  1. Loosely position left side camshaft sprocket over camshaft hub.
  2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
  3. Position primary chain onto water pump drive sprocket (10).
  4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
  5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
  6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
  1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
117016942

  1. Purge oil from timing chain tensioner using the following procedure:
    1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
    2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
117016943

  1. Reset timing chain tensioner using the following procedure:
    1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
    2. Apply a downward force until tensioner is reset.
NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.
117016944

  1. Install the reset chain tensioner (1) into the right cylinder head.
  2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
117016945

  1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
  2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
  3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
117016946

  1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
117016947

  1. Install camshaft position sensor (2) and connect electrical connector.
  2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
  3. Install upper intake manifold.
NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
  1. Fill cooling system.

Mar 27, 2013 | 2001 Chrysler Concorde

1 Answer

Suzuki wagon R 1998 camshaft chain is loose


If the chain is loose you must replace it and the auto tensioner. You do not tighten it.

Sep 26, 2012 | Cars & Trucks

2 Answers

Timing chain has a lot of slack and is rubbing against internal case. question can existing chain be tightened or must be replaced completely


The timing chain keeps the major componants in the engine alligned. A new chain will allign the engine componants better than an old chain that is sagging... and will thusly make the engine perform better and get better fuel milage as well as last longer.

I would replace the chain and not even consider the tightening of a chain that is that worn out...

You are lucky not to have the chain skip and cause the valves to come into contact with the pistons... ( read ; Interference engine)

Sep 29, 2010 | 1991 Toyota Pickup

1 Answer

How do tighten the timing belt on a 2005 pontiac grand prix ?


replace the timing belt tensioner if belt or chain still loose.

May 30, 2009 | 2005 Pontiac Grand Prix

1 Answer

I have a 99 dodge intrepid that threw a rod and my father-in-law and I have been trying to time the car for a year now. We get number one piston up but the mark on the oil pump doesnt line up with the mark...


I'm not sure what you may be "doing wrong", but here is the manufacturer procedure for aligning the timing marks.
d753c93.gif
98f82f3.gif
^Refer to this diagram during step 12.
046beb2.gif
^Refer to this diagram during step 13.
95add8f.gif
^Refer to this diagram for step 19.

1. Align crankshaft sprocket timing mark to the mark on oil pump housing. NOTE: Lubricate timing chain and guides with engine oil before installation.
2. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links.
3. Lower the primary chain with left side sprocket through the left cylinder head opening. NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
4. Loosely position left side camshaft sprocket over camshaft hub.
5. Align timing (plated) link to the crankshaft sprocket timing mark.
6. Position primary chain onto water pump drive sprocket.
7. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain and loosely position over camshaft hub.
8. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
9. Install left side lower chain guide and tensioner arm. Tighten attaching bolts to 28 Nm (250 in. lbs.). NOTE: Inspect oil ring on chain guide access plug before installing. Replace O-ring as necessary.
10. Install chain guide access plug to left side cylinder head. Tighten plug to 20 Nm (15 ft. lbs.)
11. NOTE:
To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
12. Purge oil from timing chain tensioner using the following procedure:
a) Place the check ball end of tensioner into the shallow end of Special Tool 8186.
b) Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
13. Reset timing chain tensioner using the following procedure:
a) Position cylinder plunger into the deeper end of Special Tool 8186.
b) Apply a downward force until tensioner is reset. NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball. CAUTION: Ensure the tensioner is properly reset. The tensioner body must bottom against the top edge of Special Tool 8186. Failure to properly perform the resetting procedure may cause tensioner jamming.
14. Install the reset chain tensioner into the right cylinder head.
15. Position tensioner retaining plate and tighten bolts to 12 Nm (105 in. lbs.).
16. Starting at the right cylinder bank, insert a 3/8" square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 in. lbs.).
17. Turn the left side camshaft by inserting a 3/8" square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 in. lbs.).
18. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
19. To arm the timing chain tensioner: Use a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then, release the tensioner arm. Verify the tensioner is armed (extends).
20. Install the timing chain cover, crankshaft damper, and cylinder head covers.
21. Install camshaft position sensor and connect electrical connector.

Hope this helps!
Mitchell

May 16, 2009 | 1999 Dodge Intrepid

1 Answer

B14 Timing chain problem


there is a tensioner inside the timing chain cover this is probably loosened up and therefore the chain is loose as well . the oly solution is to remove the cover and tighten the tensioner.

Oct 03, 2008 | 2003 Nissan Sentra

1 Answer

Timing chain


Do you have new chain and gears installed and what symptoms do you have.Are you changing the timing components for routine maintenance?

Aug 03, 2008 | 2002 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...