Question about 1995 Buick Regal

1 Answer

Where does the cam sensor wire connect to? - 1995 Buick Regal

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 218 Answers

The engine computer

Posted on Jun 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

07 chevy suburban ltz 4x4 6.0 traction control light and service stability light come on at random times, sometimes making check engine light come on with code p0011 cam sensor


as to the traction/stability trac check hub and abs sensors [wires and connection ] these systems are not tied into the cam sensor but ---look for wire chaffing in the harness by the cam sensor the harness may have the wiring from both systems in harness

May 31, 2016 | Cars & Trucks

2 Answers

My pt cruiser has code 1391. i changed cam sensor crank sensor wires plugs and coil still getting 1391 code and from 0 mph to 20 mph car skips and revs up any ideas?


The cam and crank sensors have the same power wire. Go after that one. They also have the same ground, but other sensors connect to it also. So it's not the ground. And they have separate return signal wires. Not them either.

Mar 09, 2015 | 2001 Chrysler PT Cruiser

1 Answer

No cam signal at pcm


Recheck the cam sensor and the wires that connect to it.

Feb 12, 2014 | 2001 Dodge Durango

1 Answer

2004 dodge neon p0344 code.


code p0344efers to cam shaft position (CMP) A bank 1---circuit intermittent==causes ---wiring---poor connection CMP sensor ---ECM
The cam sensor has to be adjusted to get the right air gap for the sensor. Check the wires to the sensor for condition and check the connection to the sensor as the pins may be dirty or wet.
you cannot adjust the timing belt to prevent missing because if you could there would be a massive dollar repair bill from engine damage.
missing can be from other sources such as faulty injectors and low fuel pressure so have the fuel pressure checked and have the injectors removed and cleaned.

Dec 26, 2013 | Cars & Trucks

1 Answer

WHAT IS THE CODE P0341


This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than:
  • Poor fuel economy (if engine runs)
  • Possible no start condition
Causes A code P0341 may mean that one or more of the following has happened:
  • Cam sensor wiring routed too close to spark plug wiring (causing interference)
  • Poor wiring connection at cam sensor
  • Poor wiring connection at PCM
  • Bad cam sensor
  • Damaged reluctor wheel
Possible Solutions Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following:
  • Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.)
  • Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing
  • Visually inspect the cam sensor for damage
  • Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage
  • If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
  • If all checks out okay, then replace the sensor.
Related Camshaft Trouble Codes: P0340

Mar 07, 2012 | 1996 Saturn SL

2 Answers

I have code po341 car will start and idle for 15 seconds and die and will start back up and do the same everytime


p0341 camshaft position sensor circuit range /performance didnt specify what vehicle but check the wiring and connection for the camshaft position sensor if looks good than problem with sensor not an expensive fix

Nov 23, 2011 | Cars & Trucks

1 Answer

96 vw golf p0341 error code


This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.

Symptoms: The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than:
Poor fuel economy (if engine runs)
Possible no start condition


A code P0341 may mean that one or more of the following has happened:
Cam sensor wiring routed too close to spark plug wiring (causing interference)
Poor wiring connection at cam sensor
Poor wiring connection at PCM
Bad cam sensor
Damaged reluctor wheel


Possible Solutions: Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following:
Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.)
Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing
Visually inspect the cam sensor for damage
Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage
If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
If all checks out okay, then replace the sensor.


Check this diagnostic test (click over image for zoom)...

zjlimited_743.gif


Hope this helps (remember to rate this free answer).

Sep 27, 2011 | 1996 Volkswagen Golf

1 Answer

1998 saturn sc2 po341


P0341 - Camshaft Position Sensor Circuit Range/Performance

This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.

Symptoms: The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than:
* Poor fuel economy (if engine runs)
* Possible no start condition


Causes: A code P0341 may mean that one or more of the following has happened:
* Cam sensor wiring routed too close to spark plug wiring (causing interference)
* Poor wiring connection at cam sensor
* Poor wiring connection at PCM
* Bad cam sensor
* Damaged reluctor wheel

Possible Solutions: Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following:
* Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.)
* Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing
* Visually inspect the cam sensor for damage
* Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage
* If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
* If all checks out okay, then replace the sensor.

Related Camshaft Trouble Codes: P0340


Hope helps (remember to rate this answer).

Jan 03, 2011 | Saturn SC2 Cars & Trucks

2 Answers

HONDA CR-V


OK, you have a code PO341 which means their is a problem with the signal the ECU is receiving from the cam sensor. It does not necessarily mean the sensor is bad. It can be one of these things.
1. Cam sensor wiring routed too close to spark plug wiring (causing interference) 2. Poor wiring connection at cam sensor 3. Poor wiring connection at PCM 4. Bad cam sensor 5. Damaged reluctor wheel You replaced the cam sensor and the problem is still there so we can assume that a defective cam sensor was not the problem. Do this.
1. Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.) 2. Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing 3. Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage 4. If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)

Aug 24, 2009 | 2002 Honda CR-V

1 Answer

2003 stratus cam sensor replaced still unresolved


you bypassed the wires that connect to the sensors? that would have been my first guess the harness that plugs into the sensor. after that i would check the ground connection from the ecm. wouldn't hurt to check the battery posts too. if the battery posts are oxidized you can have all kinds of goofy electrical problems. hope that helps.

May 27, 2009 | 2003 Dodge Stratus

Not finding what you are looking for?
1995 Buick Regal Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...