Question about Mazda B2200

1 Answer

Hi i'm after the tightening torques for a mazda e2000 2.0ltr petrol cylinder head.

Posted by on

  • samukwhite Jun 04, 2010

    thank you very much. great stuff

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

Mazda E2000 2.0 ltr. petrol, engine code FE
Cylinder head tightening torques:
Renew bolts: No
1. Stage 1: Tighten torque = 20 ... 26 Nm
2. Stage 2: Tighten torque = 50 ... 56 Nm
3. Stage 3: Tighten torque = 80 ... 86 Nm

Tightening sequence:

hi i'm after the tightening - f6c3238.png

Posted on Jun 04, 2010

  • TDISLine
    TDISLine Jun 04, 2010



    Better picture:




×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the torque setting for my citreon 1.8 16v cylinder head petrol


If you buy head gasket the setting will be included. I believe you will torque to a given torque then tighten a further angle (probably 120degrees.)

Jan 26, 2015 | 2004 Citroen Xsara Picasso

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

What is the tightening for a head bolt torque for a 1998 kia clarus in nm ,dohc 2.0 petrol


Cylinder Head Bolts
  • The 10 cylinder-head bolts should be tightened to a torque of 59 to 64 ft-lbs.
Cylinder Head Cover Bolts
  • The 15 cylinder-head cover bolts should be tightened to a torque of 35 to 52 ft-lbs.

Apr 08, 2013 | Cars & Trucks

1 Answer

2000 model mazda 323 astina cylinder head bolt torque specs


Three stages with new bolts (a must), 1st 60 pounds, then 70 pounds then final torque is 80 FT Pounds.

Feb 16, 2012 | Mazda 323 Cars & Trucks

1 Answer

Hello! I have a Mazda MPV v6 3.0 93 I need your help,i remove the heads and i need to reinstall,I need to know: head torque secuence and tighten on bolts. thank you everybody


TORQUE ALL BOLTS PROPER SEQUENCE TO 14 FT LBS.THEN PAINT MARK ON THE OF EACH BOLT.USING MARK AS A REFERENCE TIGHTEN ALL THE BOLTS PROPER SEQUENCE AN ADDITIONAL 90 DEGREES.THEN TIGHTEN ALL BOLTS IN SEQUENCE ADDITIONAL 90 DEGREES. WRITE THIS NUMBER ON A PIECE OF PAPER. 8 4 1 5 AND UNDER THAT NUMBER WRITES THIS NUMBER UNDER THE NUMBER JUST GAVE YOU 7 3 2 6 THIS IS YOUR CYLINDER HEAD BOLT TORQUE SEQUENCE.

May 31, 2011 | 1993 Mazda MPV

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Hi, I`m looking for the torque settings for the cylinder head on an audi a4 1.8 1997 petrol


Cylinder head instructions for Audi A4 1.8 (1997)

Tightening sequence:

9c9e892.jpg
Renew cylinder head bolts: Yes
Stage 1 - Tighten: 40 Nm

Stage 2 - Tighten: 60 Nm
Stage 3 - Tighten: 90 degrees
Stage 4 - Tighten: 90 degrees

Sep 21, 2010 | 1998 Audi A4

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

1 Answer

Ford-explorer 2005 v6 petrol cylinderhead tightening torques


a part place can give you a print out on the tor spec advance or auto zone

Jan 14, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

688 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...