Question about 2002 Chevrolet TrailBlazer

1 Answer

How to loctae a crank shaft sensor for a 4wheel

How to locate a crank shaft sensor for a 4wheel drive chevy trailblazer ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Sits on the side of the engine block, held on with a 8 or 10mm bolt, remove bolt and sensor slides right out.

Posted on Jun 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2005 chevy trailblazer Ls 4.2 4wd 6cilinders and I have code c0055 vehicle speed sensor circuit.and I need to know where is this sensor located or how to fix it


It depends there are 3 speed sensors 1 on each front wheel and 1 on the output shaft of the transmission.They all talk to each other and the computer All generate a refferance voltage .5 volts and send a signal to the pcm or vcm or ecm .Small problem are like the ones on the front big problems the out put shaft

Apr 08, 2015 | 2005 Chevrolet TrailBlazer LS

2 Answers

Would like to know where the Cam Shaft Sensor is located in 2002 Trailblazer.


it is the sensor that is being pointed at in the cylinder head


9a01378.jpg

Sep 12, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

2006 chevy trailblazer replace 4wheel drive selector


i've got a 2003, and i believe the parts and procedures are the same for the years. there are screws in the dash trim by the ciggarette lighter, and more on the underneath of the dash pad where the gauge cluster is. then carefully pop the dash trim out. there are retaining clips that hold it in besides the screws. they should pop out without too much effort. i'd start near the radio and be careful. there also may be two more screws near the bottom of the steering wheel that you'll have to remove the trim below it to get at.

Feb 06, 2010 | 2006 Chevrolet Trailblazer

2 Answers

Where is the crank sensor located on a chevy malibu 2001


It should be down near the crankshaft pulley. Remove the the right front wheel and the splash shield, it should be there next to the pulley.

Dec 20, 2009 | 2001 Chevrolet Malibu

1 Answer

Crank shaft sensor? is this the same as cam shaft


no each one has its own job,
crank sensor is counting crank shaft rpms
cam sensor is counting cam shaft rpms
is there any lights coming on just as this is happening?
i think you should have the fuel pressure checked when it dies out,you need at least 50psi at fuel rail

Dec 08, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

2003 trailblazer lt 4wheel drive


  1. Remove the tire and wheel center cap.
  2. Remove the drive axle nut.
  3. Raise and support the vehicle. Remove the tire and wheel. .
  4. Remove the brake rotor.
  5. Disengage the wheel drive shaft from the wheel hub and bearing. Place a brass drift against the outer end of the wheel drive shaft in order to protect the wheel drive shaft threads. Sharply strike the brass drift with the hammer. Do not attempt to remove the wheel drive shaft from the wheel hub and bearing at this time.
  6. Remove the wheel hub and bearing from the steering knuckle by removing the three bolts coming in from the back side of the knuckle.
Of course you may have to use a hammer to loosen the bearing from the knuckle.

Good Luck

Sep 05, 2008 | 2004 Chevrolet TrailBlazer

1 Answer

2002 Chevy Trailblazer Engine Codes


This is actually an easy swap out. Remove the electrical connection, remove the retaining bolt and pull out old one. I believe the sensor is located in the front passenger side of the engine on this particular model.

Jul 06, 2008 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...