Question about 1999 Subaru Legacy

Open Question

Trying To adjust the Headlights on '99 Subaru Legacy L, point too low. I cant find the vertical adjustment knob and my owner manual had no useful information

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: automatic shift knob stuck in

do you here a clicking sound from the shifter when you push the brake pedal. if not check the switch on the brake pedal. good luck

Posted on Nov 24, 2008

Ad
  • 116 Answers

SOURCE: subaru legacy repair manual

autozona sells repair manuals

Posted on Dec 10, 2008

5LTRBTR
  • 180 Answers

SOURCE: owners manual for 99 subaru imprezza

http://www.megaupload.com/?d=JGRQH96N how to use megaupload
http://www.katzforums.com/showthread.php?t=106329

Posted on Dec 21, 2008

  • 1986 Answers

SOURCE: Adjusting Headlights of a 2006 Hyundai Sonota

The headlamps are adjusted by a wheel which can be operated by aphillips screwdriver. There's a hole in the top of the headlamphousing or radiator support which leads to the wheel with little teethon it on the back of the headlamp. The lamps on your car emit a veryshort but wide beam, so no horizontal adjustment should be needed.


http://www.automedia.com/Aiming_Headlights/ccr20010801ha/1

Posted on Aug 13, 2009

  • 811 Answers

SOURCE: 99 Subaru Legacy auto Transmission will not Engage right away P-D

change fluid and filter

Posted on Oct 04, 2009

Testimonial: "Right on the money!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to aim headlights-2002 forester


ALL headlights have vertical and horizontal adjustments. The vertical may be obvious, an M8 shaft. Horizontal may be non obvious, or the adjuster is covered with a rubber grommet. Once you've located the adjusters, find a wall eve on mall car park, and see the low beam to the same height. Check high beam, and a just the horizontal as needed.

May 23, 2014 | 2006 Subaru Forester

1 Answer

Just bought a used 05 subaru impreza. Noticed the right head lamp is pointed too high. where is the adjustment screws to lower the lamp. It seems great on the horizontal just needs to be adjusted on the...


I hope this info helps!

ADJUSTMENT

HEADLIGHT AIMING

CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than 2 minutes.


  1. Before checking the headlight aiming, be sure of the following:
    • The area around the headlight has not sustained any accident, damage or other type of deformation.
    • Vehicle is parked on level ground.
    • The inflation pressure of tires is correct.
    • Vehicles gas tank is fully charged.
    • Bounce the vehicle several times to normalize the suspension.
    • Make certain that someone is seated in the driver s seat. Turn the headlights on and then adjust the low beam pattern to the following positions on the screen.
  1. Position the headlight beam leveler switch to "0" .
129148368


129148369


129148370



  1. Rotate the adjusting screw (A) to adjust aim.

Aug 01, 2011 | Subaru Impreza Cars & Trucks

1 Answer

How do you aim or adjust 200l legacy headlights


Hello Terry.

HEADLIGHT AIMING



CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than two minutes .
NOTE:
Before checking the headlight aiming, be sure of the following:
  • The area around the headlight has not sustained any accident, damage or other type of deformation.
  • Vehicle is parked on level ground.
  • The inflation pressure of tires is correct.
  • Vehicle's gas tank is fully charged.
  • Bounce the vehicle several times to normalize the suspension.
  • Make certain that someone is seated in the driver's seat.
  1. Place a cloth over the headlight that does not require aiming adjustment.
  2. Turn the headlights on. Perform the aiming adjustment for the other headlight as follows:
kiltylake_66.gif

CAUTION: Do not perform lateral headlight aiming adjustment.There you are, the procedure from Subaru manual.

Hope this helps you.
Thank you for using FixYa.

KL

Dec 04, 2010 | 2001 Subaru Legacy

2 Answers

How do you adjust the aim of the headlamps on a 2006 subaru legacy


there should be two screws one on top of the headlight and one on the side park the car on a level servise and adjust the headlights till thay are right in front of the car most cars the screew is a filips head

Mar 09, 2010 | 2006 Subaru Legacy

1 Answer

Adjust the headlight beam on 2002 Subaru Outback


two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks

Nov 09, 2009 | 2002 Subaru Outback

1 Answer

High beam adjustment, how do you do it seams mine are reaching for the stars thaks john in wisconsin


two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks.
To start you will want to pull your car quite close to the surface you are using to aim your headlights. This is done to allow you to mark, with the masking tape, where the headlights are on the car. With the car right up against the vertical surface, and your low beam headlights on, the center of the beams will be directly in front of the headlights. Use your masking tape to mark straight across where the headlights are shining. Use short pieces of masking tape to mark vertically the center of the low beams.
, back your car about 25 feet away to check the alignment of the headlights. The brightest spot on your low beams should be about two inches below the masking tape and slightly to the right of the vertical marks. Use the adjustment screws to move the beams up and down, and right and left, until the headlights are aimed properly.
If your car only has two headlights, that's all you need to do. With the high beam lights integrated into the single headlight there is no further adjustment possible. If you have a four-headlight system you will next need to adjust your high beams. Switch to your high beams and adjust them so they shine just below the line and are centered between your two vertical marks.

good luck

Nov 05, 2009 | Volkswagen Jetta Cars & Trucks

2 Answers

Can't find the adjustment knob for the headlights on a 2008 Mazda


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jun 09, 2009 | 2008 Mazda Mx 5 Miata

3 Answers

How do i adjust the headlight beam on my Subaru Forester X MY06 Model


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Apr 26, 2009 | 2006 Subaru Forester

1 Answer

Adjusting the headlights on a '97 Geo Prizm


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Mar 25, 2009 | 1997 Geo Prizm

1 Answer

Headlight adjustment 1999 S70


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Aug 18, 2008 | 1999 Volvo S70

Not finding what you are looking for?
1999 Subaru Legacy Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...