Question about 1993 Isuzu Trooper

1 Answer

We have a intermittent problem when the trans drops into failsafe, Turn the key off and it resets We have checked all the earths But it still does it Regards Steve

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 10,515 Answers


Do you see any Check Engine Light Being On?

If yes, get the Car Scanned. I am pretty sure, you might get Codes like P0753 or P0758.Once you would get the Codes, Revert and i would be able to assist you.

If the Check Engine Light is not ON, Revert now and i would be able to assist you.

Let me know,once done.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Jun 04, 2010

  • steve_howell Jun 04, 2010

    No Check Engine Light No Codes in either Trans or Engine.No Data Stream Available (early type computer) only does it on deacceleration


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 bmw x5 trans failsafe program message after oil change

First check transmission dip stick for correct fluid level. Next schedule a transmission filter change. This should have been done at 60,000miles

May 25, 2017 | BMW X5 Series Cars & Trucks

1 Answer

The engine fail safe program light came on in my BMW X5 2006 and now the car won't start ...can It be reset?

Depends why the Failsafe was triggered. Read the codes would be a good way to start. Anyway, since the car wont start, it may be the crankshaft position sensor, which will cause a trans failsafe and prevent the car from starting.

Apr 14, 2017 | BMW Cars & Trucks

1 Answer

How do I reset the "transmission failsafe program" light on the dash? The car seems to drive normal except for that light being on.

Keep driving it, you will have a $5,000 repair bill

Stop using it & hope you can save the trans with the
proper diagnosis, to find the reason it went into failsafe

Jul 21, 2014 | 2005 BMW X5

1 Answer

Vehicle not starting

Could be in safe mode. Top off trans fluid. Reset computer either by code reader or battery cables for an hour or so.

Nov 06, 2013 | Ford Cars & Trucks

2 Answers

Intermittently does not start- not a battery problem

Could be an earth problem, take off the earth strap from the battery to the car body, clean any corrosion and replace, do the same with the body to engine strap.

Nov 04, 2010 | 1998 Lexus LS 400

1 Answer

Freelander engin cuts out and all dash lights go out turn key off and back on it stats as normal why

petrol or diesel check the security of the relays and the fuses in the fuse box they work loose.engine compartment. also check the earth connection to the chassis. this is an intermittent fault your also might want to look at the engine earth strap. final thought check the multi plug connection on to the ecu, good luck.

Oct 05, 2010 | 2002 Land Rover Freelander

2 Answers

My jeep clicks when i turn the key on and will not start till it quits

If the battery is OK ,then it sounds like a faulty / intermittent Earth connection. Check all the battery power and earth leads where they connect to the Battery, Engine, Starter Motor and Body. If possible disconnect, clean thoroughly by removing any corrosion or paint that could cause a poor connection, and reconnect making sure all are tight.

Sep 29, 2010 | 1995 Jeep Wrangler

1 Answer

I also have a trans.failsafe prog.indicator light on my 2000 bmw

You have an alternator or battery concerne,low voltage caused all the other problems,Start with a battery,then have alternator tested.The failsafes are designed to keep from burning up solenoids and other electronic components.

Jun 19, 2009 | 2000 BMW 7 Series

1 Answer

Electrical prob: passenger mirror, drivers window and cabin fan

there is a very good chance that you have a very poor earth (ground) connection. check all the the earth wires make sure that they are clean and tight even the ones under the dash you might have to look at a user manual to check where all of the earths are some are hidden away behind carpets and plastic trims all of these need checking remove them rub with abrasive cloth and refit making sure they are tight.

hope you find this helpful Regards JR

May 31, 2009 | 1999 Chevrolet Venture

1 Answer

93 dodge intepid

Possibly failsafe.Have vehicle scanned for codes,repair codes.If no codes,drop trans pan and evaluate condition of the fluid and pan contents.Also have technician look at cvi's in the data stream of the scan tool.Cvi's are clutch volume indexes,and very good indicators of wear inside the trans.Many things can cause what you are experiencing,inlcuding,but not limited to,input or output speed sensors,solenoid block,transmission control module,or internal trans damage.

Jul 12, 2008 | 1993 Dodge Intrepid

Not finding what you are looking for?
1993 Isuzu Trooper Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides