Question about 2000 Chevrolet Silverado

1 Answer

My keyless entry does not work with with my control I push the button and it does nothing how do I trouble shoot it to make it work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 749 Answers

The key fab may need a new battery.If you pop the cover open a very common issue is the battery contact points solder breaks.You can try to resolder if this is the problem.Another suggestion while you have it apart is to clean it.Typically when cleaning these I use a 91 percent rubbing alcohol and a q-tip.Remove the circuit board from the case with battery out you will see the rubber buttons.Gently wipe them out with an alcohol q-tip and on the board itself clean the contact points where the buttons meet the circuit board.If this does not work the fab may need to replaced.

Posted on Jun 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesn't the horn beep when i lock my doors with the remote on my 03 malibu is it a bad relay


When you push the horn switch (button) on the steering wheel ,do the horns work then ? The BCM - body control module energizes the horn relay for keyless entry operation . Start by having BCM checked for DTC'S - diagnostic trouble codes .

Mar 03, 2016 | Cars & Trucks

1 Answer

Keyless receiver


immobilizer control module under the dash.some vechicles if you replace key remote dealership has to reprogram remotes using diagnostic equipment.try this techinique to synchronize remote transmitter. stand within 5 feet from vechicle .press transmitter lock and unlock buttons simultaneously for 7 seconds . system will lock and unlock doors confirming synchronization. if this dont help dealership has to reprogram remotes.

Dec 13, 2013 | 1997 Chevrolet Blazer

1 Answer

2009 Buick Lacrosse automatic door locks, interior button and fob not working


Have you had it checked to see if DTC'S - diagnostic trouble codes stored in the BCM - body control module ? That's the first thing you should have done . Dealer or other independent reair shop that has a factory or professional type scan tool . Auto part stores can't pull these codes .
The keyless entry system has the following main components:
• The transmitters
• The body control module (BCM)
• The remote control door lock receiver (RCDLR)--When you press a button on the transmitter, the transmitter sends a signal to the RCDLR. The RCDLR receives the signal and sends a serial data message requesting the appropriate function from the BCM.
• Keyless Entry Antenna which is a coaxial cable that runs from the RCDLR to the back glass. It attaches with a 9 volt battery style connection to a grid on the back glass, this style antenna is used to increase range and performance for Keyless Entry and Remote Vehicle Start systems .

Jun 10, 2017 | 2009 Buick LaCrosse CXL

1 Answer

Honda CRV Keyless Entry stopped working. Pushing any button on either remote does nothing. They both just stopped working at the same time out of the blue. All doors function properly from inside


Check the batteries in the remotes. It might just be a massive coincidence and the 2 stopped working at the same time. Failing that I would guess the reciever is the problem

Dec 04, 2012 | BMW X5 Series Cars & Trucks

1 Answer

2000 oldmobile bravada keyless entry remote won't work


You most likely have a problem with the car computer. It is programmed to control that as well as the rest of the vehicle's functions. Have the computer tested by a mechanic.

Apr 29, 2012 | 2000 Oldsmobile Bravada

1 Answer

Keyless entry does not unlock doors, open trunk, or start vehicle (remote start built onto keyless entry). Battery is new in BOTH remotes and neither one works. Could a fuse in vehicle be bad? Secondly,...


RFA / MOD fuse 10amp . location - insturment panel fuse box. Fuse Block - I/P
Right side of the I/P, behind the access panel
If the fuse is good your best bet would be to take it to a qualified repair shop , that doesn't mean the dealer . Lot of good independant repair shops around , just have to check the yellow pages.
Do you know what DTC'S are ? diagnostic trouble codes ! Not only the ones for the engine management system OBD 2 . There are also DTC'S for the remote keyless entry system , BCM - body control module. You need a factory or professional scan tool to view this codes
DTC B3101
DTC B3102
DTC B3103
DTC B3106

The remote control door lock receiver (RCDLR) communicates with the body control module (BCM) through the keyless entry serial data circuit. When any button on the keyless entry transmitter is pressed, the transmitter sends a signal to the RCDLR. The RCDLR sends a lock, unlock, or panic alarm request to the BCM, depending on which button is pressed on the transmitter. The BCM receives the message and performs the appropriate function. The BCM also uses the keyless entry serial data circuit in order to communicate with the RCDLR when programming transmitters. Do you know what serial data circuits are ?

DTC B3101 Keyless Entry Data Link Circuit Range/Performance
DTC B3102 Keyless Entry Data Link Circuit Low
DTC B3103 Keyless Entry Data Link Circuit High
DTC B3106 Keyless Entry Data Link Parity Error

This is what the factory manual said as to the location of power steering fluid reservoir ! Not much help , you would do better googling it.
The power steering fluid reservoir holds the power steering fluid and may be integral with the power steering pump or remotely located. The following locations are typical locations for the remote reservoir:
• Mounted to the front of the dash panel
• Mounted to the inner fender
• Mounted to a bracket on the engine

Aug 19, 2017 | 2005 Buick LaCrosse

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

2006 power door locks wont`work


Resistor is blown...take the truck to an automotive electronics/stereo shop that installs keyless entry systems ($89) and put an aftermarket keyless on the truck. They'll have to trouble-shoot the system to make the installation of the new keyless!

Jun 14, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Keyless entry blinks dome light and does nothing else


The remote is fine - your problem is the lock actuators in the doors. They're a bit of a pain to replace - so, you may want to have a professional do it.

May 03, 2009 | Dodge Dakota Cars & Trucks

2 Answers

My remote for the keyless entry does not work.


does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back

Mar 22, 2009 | 2004 Lincoln LS

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...