Question about 1997 Plymouth Voyager

1 Answer

Install serpentine belt 1997 grand voyager

Install serpentine belt on a 1997 grand voyager 3.3 liter

Posted by on

  • Dean Stewart
    Dean Stewart Dec 28, 2011

    The nut is a 15mm, and it needs to rotate as much as you can to get it on. I leave the belt off the Water pump, not the tensioner, so I get more room to the wrench on the tensioner nut.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

REMOVE/INSTALL
GENERATOR, POWER STEERING PUMP
, AIR CONDITIONING COMPRESSOR AND WATER PUMP DRIVE BELT

The Poly-V Drive belt is provided with a dynamic tensioner to maintain proper belt tension. To remove or install this belt.

1. Raise vehicle on hoist.
2. Remove right front splash shield.
3. Release tension by rotating the tensioner clockwise
4. Reverse above procedure to install.


install serpentine belt 1997 grand voyager - a38eeee.gif

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Jun 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace 97- plymouth voyager belt tensioner


For the 1997 3.0 liter Grand Voyager:

Remove A/C belt. Release tension on serpentine belt by moving the tensioner, then remove the belt. Be sure to note how the belt is routed.

From way back underneath the car look up along the exhaust pipe leading to the rear manifold, you can just see the bolt on the back of the tensioner to the right of the rightmost spark plug boot (looking forward from under the engine). Route a socket (15 mm I think) on a short extension up along the exhaust pipe and shield (make sure it's cold!), you can just get it onto the bolt. Then snake a socket up and connect to the extension, no universal joints needed. There's just enough room to get enough leverage on the bolt to remove it. From then on it's simple.

I replaced my tensioner a few hours ago as above.

Mar 21, 2012 | 1997 Plymouth Voyager

1 Answer

Im trying to change the alternator in my 1997 grand voyager 3.3 liter v6 and o have the old one all disconnected. how do i get it out to put the new one in.




) IMPORTANT - Disconnect the neg battery terminal (IMPORTANT) 2) Release the spring loaded tensioner (makes the serpetine belt tight). The control bolt that keeps it tight is right tunder the alternator (1994 Voyager). Use a long handled torque wrench. 3) Hold on the to serpentine belt (otherwiuse it'll be a mess) keep it tight-ish. Pass a stick through it and keep it tight or prop it up with a bungies or something!!! Be gentle. 4) Two bolts hold the alternator, one is obvious the other is more towards the back. Watch your knuckles be gentle but strong. Remove the nuts, gently lift it out and hold it there. 5) Disconnect the leads from the the electrical that are attached. Place the old one on the bench. 6) Watch that belt!!! 7) Get the new alternator. 8) Connect the electrical. 9) Bolt it in. 10) Place the serpetine belt in the groove, careful make sure it doesn't pop out anywhere else below. Popping out (even one groove) and driving it could destroy your belt. 11) Back to the tensioner, relase slowly, it will make itself tight again. 12) Attach the battery again. 13) Start the car. 14) IMPORTANT remember, clean those battery posts and cable leads. the dirt won't allow full contact thus minimal recharge. Trust me, been there.

Dec 15, 2010 | 1997 Plymouth Grand Voyager

1 Answer

How do you release the tensioner in a 1997 voyager


Relieve tension, then pull belt off at easiest spot near you like other pulley . Please confirm what engine.

Oct 05, 2009 | 1997 Plymouth Grand Voyager

1 Answer

Serpentine belt and tensioner replacement 1999 Plymouth Grand Voyager 3.3 liter V6 engine


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 20, 2009 | 1999 Plymouth Grand Voyager

1 Answer

Belt configuration


http://www.2carpros.com/car_repair_information/tec_info/1997/pontiac/grand_prix/1997_pontiac_grand%20prix_drive_belt_routing_diagram.htm

scroll down to the very bottom of this page in the link , yours is the last 2 pictures - with or without air conditioning . cheers .

Jan 11, 2009 | 1997 Pontiac Grand Prix

Not finding what you are looking for?
1997 Plymouth Voyager Logo

Related Topics:

998 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...