Question about 1994 Honda Civic

2 Answers

Tire thread broke off when i was tightening it. what do i do

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,016 Answers

Hi,

you need to remove the tyre again, If it is the front wheel, take the rotor assembly off and punch the wheel stud out.

If it is the back whell it is a bit more difficult.

But the wheel stud can be removed and a new one put in place.

Hope this helps

Jason

Posted on Jun 04, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! You will need to replace the stud for sure. Buy a new one on your local auto supply and remove the old stud. YOu can perform this by taking off the wheels, it can be pull out from the back. Hope this helps and have a good one!

Posted on Jun 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intake manifold 89 fire f150 5.0 efi 302


IF it broke off while tightening , drill a hole in the center and use a easy out tool to remove it . if it broke off while trying to remove it the tool will likely not work as it is seized , you will have to use a drill for that size thread and tap in a new thread , best left to a pro.

Jun 04, 2017 | Cars & Trucks

1 Answer

Broken studs on brake disc/rotor


Check out this video on the subject.

http://www.youtube.com/watch?v=Z0avY0p0PU4

Apr 14, 2014 | 1994 Toyota Camry

1 Answer

Manual transmission line leaking at transmission


Take your wrench set,and gently tighten the leaking line...start up and drive around the block..recheck for leaks...if it still leaks,a bit of thread tape may be necessary. Disconnect line,wrap threads and retighten..do not over tighten.to avoid stripping the threads. Good luck,and chock the tire before doing an of this.

Nov 01, 2013 | 2000 Chevrolet Blazer

1 Answer

How to get the starter off


  1. this also depends on which motor but this is for 4.3
  2. Disconnect the battery negative cable.
  3. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  4. Remove the front tire and wheel assembly from the right side of the vehicle. Refer to Wheel Removal in Tires and Wheels.

  5. 141840.gif
    tif.gif
  6. Remove the differential carrier shield mounting bolts, if equipped.
  7. Remove the differential carrier shield, if equipped.

  8. 43021.gif
    tif.gif
  9. Remove the wires from the solenoid.

  10. 395641.gif
    tif.gif
  11. Remove the starter mounting bolts by accessing them below the right wheel house panel.

  12. 395675.gif
    tif.gif
  13. Remove the starter from the vehicle.
  14. Note the location of the shims, if equipped.
Installation Procedure

    395675.gif
    tif.gif
  1. Install the starter and the inboard starter mounting bolt. Do not tighten.
  2. Install the starter shims, if equipped.

  3. 395641.gif
    tif.gif
    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the outboard starter mounting bolt.
  5. Tighten
    Tighten the starter mounting bolts to 50 N·m (37 lb ft).

    43021.gif
    tif.gif
  6. Connect the wires to the solenoid.
  7. Tighten • Tighten the battery positive cable nut to 9 N·mN·m (80 lb in). • Tighten the engine wiring harness to starter nut to 1.9 N·m (16 lb in).
    141840.gif
    tif.gif
  8. Install the differential carrier shield, if equipped.
  9. Install the differential carrier shield mounting bolts, if equipped.
  10. Tighten
    Tighten the differential carrier bolts to 25 N·m (18 lb ft).
  11. Install the tire and wheel assembly. Refer to Wheel Installation in Tires and Wheels.
  12. Lower the vehicle.
  13. Connect the negative battery cable.

Jul 31, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Broken stud on left front wheel


Remove: wheel, brake caliper & rotor. Drive out the remaining stub with a hammer and punch. Insert a new stud and pull it into place by tightening the lug nut. Before running out of threads, remove the nut, insert a stack of washers or a large nut which slips over the threads without contacting them, tighten the lug nut to seat the stud.

Jul 12, 2009 | 2001 Pontiac Sunfire

1 Answer

I was trying to remove my front passenger tire & broke wheel stud


You just have to hammer it out. and rotate the hub so you can get it out. then put the new 1 on and tighten a lug on it till it's locked in

Jun 05, 2009 | 2005 Pontiac Grand Am

2 Answers

Broken Lugs For a Chevrolet Trailblazer


I might try a different shop. I have never heard of a broken Stud nut making any noise I hope they diagnosed a problem with the noise. Also in-experinced tire tech's over tighten lugs with their impact wrench and snap broken studs

Apr 17, 2009 | 2004 Chevrolet TrailBlazer

2 Answers

Mechanics keep on breaking my lug nuts,Why?


Over tightening. They are probably using an impact wrench to tight the lugs because its the fastest way. Its not the right way though.
Here is what happens. When the nuts are tightened, the studs will stretch. This tension holds the wheels on to the rim. If you over tighten the studs you can damage them and they could fail. The best approach is to use an impact wrench to snug up the nuts. Then go back with a torque wrench and tighten to the manufacturer specifications.(lug nut torque for your vehicle is 110 ft-lbs ) Next time you are having your tires rotated or changed, make sure the mechanic uses a torque wrench and the correct torque.

Feb 05, 2009 | 2005 Dodge Caravan

1 Answer

Lug bolt on front drivers side wheel is broken & needs replaced. I'm doing the job.


Safely jack and support the vehicle,remove wheel and tire assembly,with a punch and ball peen hammer (and safety glasses) or just a hammer,carefully knock broken stud out of the hub,it will fall out the back.Now take new stud and spin the hub until you find a spot where it will insert into the hole from the backside.Start the stud through the hole from the backside of the hub.Now at this point,you are going to PULL the stud into the hub,but the threads must be protected from galling.I use Anti Seize compound and some flat washers.Liberally coat the threads of the new stud with anti seize compound to protect the threads,stack some flat washers on the stud,install the lug nut,and tighten by hand.The stud will pull into the hub some.Remove lug nut,and stack more washers on the stud,and repeat the tightening process.Repeat process until stud is fully seated.Now remove anti seize compound with brake cleaner or equivalent solvent.Reinstall wheel and tire,and call this job completed.Remember to rate this solution.Good luck.

Sep 01, 2008 | 2001 Honda Civic

Not finding what you are looking for?
1994 Honda Civic Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...