Question about 1984 Chrysler LeBaron

1 Answer

How to replace a 1984 Chrysler Lebaron ignition switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,297 Answers

The ignition switch is located under the dash on the steering column and is simple....
disconnect connector, remove to screws and replace switch

if however, you mean the ignition tumbler, the place where you put the key, then it a lot tougher


Posted on Jun 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key ignition broke my Husband took it apart and all these springs shot all over the place


You will need to replace the key cylinder and likely the ignition switch. Have done at dealer or reputable shop.

Nov 20, 2013 | 1984 Chrysler LeBaron

1 Answer

Ignition time delay relay gets really hot


replace the shorting out module. The transformer in that module has a short

Sep 01, 2012 | 1984 Chrysler LeBaron

1 Answer

Wiring diagram for 1984 Chrysler LeBaron ignition system


Try repair manual here
http://www.manualslib.com/

Oct 23, 2010 | 1984 Chrysler LeBaron

2 Answers

Ignition switch 1992 Lebaron


Hello! Disconnect +battery cable...Remove tilt lever...Remove 3 Torx column cover attaching screws...Then the upper and lower column column covers...Using a Torx with a security tip (also called tamper proof tip) #440-tx20H... Remove 3 ignition switch mounting screws...Carefully pull switch away from column...Release 2 connector locks on 7 terminal wiring connector...Then disconnect from ignition switch...Release connection lock on 4 terminal connector...Then disconnect from ignition switch.

Guru..................saailer

Jan 12, 2010 | 1992 Chrysler Lebaron

1 Answer

1994 chrysler lebaron 3.0 Ignition started


You have lost the accessory power feed due to high resistance at the ignition switch connector.
Most likely the switch will need to be replaced and if the harness plug is not heat damaged too bad you may be able to clean and crimped the terminals a little for better contact. In some cases you can buy just the connector end from the dealer as a repair part.

Dec 27, 2009 | 1994 Chrysler LeBaron

1 Answer

95 chrysler lebaron gtc 3.0 starts for a second and then stalls out


What is the fuel pressure reading at the fuel rail?

Mar 19, 2009 | 1995 Chrysler LeBaron

1 Answer

Engine misses


you could have a blown head gasket in between two cylinders.or you need to change your fuel pressure regulator,you might need a new fuel filter..

Dec 02, 2008 | 1984 Chrysler LeBaron

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...