Question about 1996 Chevrolet Blazer

1 Answer

Signal lights not working

I have replaced fuse and bulbs are good. now i am trying to locate flasher to replace. it is not in fuse box. Where is it?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 218 Answers

Open the glove compartment thay are in the back

Posted on Jun 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My saturn signal light work sometime than go off if it the flasher please tell me there it is in my car


IF TURN SIGNAL LIGHT DONT WORK SOME TIMES.CHECK FOR BLOWED OR LOOSE FUSE.CHECK TURN SIGNAL BULBS AND CHECK BULB SOCKETS FOR CORROSION.CHECK TURN SIGNAL FOR BAD GROUND.USE JUMPER WIRE BETWEEN GROUND SIDE OF THE TURN SIGNAL BULBS AND A GOOD CHASIS GROUND.IF ALL IS GOOD TURN SIGNAL SWITCH IS BAD OR FLASHERS GOING BAD.TURN SIGNAL FLASHER LOCATED ON CENTER CONSOLE SIDE PANEL GRASP THE FLASHER UNIT AND DETACH IT FROM THE FUSE BOX.IF YOU HAVE EARLY MODEL VECHICLE FLASHER UNIT LOCATED AT THE FRONT OF THE FUSE BLOCK.

Aug 23, 2011 | Saturn LS Cars & Trucks

2 Answers

I have a Frontier XE 2001. Niether turn signal works have good bulbs and fuses are OK. Where else should I look.


did both signal lights stop working at the same time or not,it may just be the signal flasher has gone bad,it is located under the dash by the fuse panel.if the hazard flashers work then i would say the signal flasher is bad.with the hazards on you can locate it and that is what the signal flasher looks like and it is a separate flasher,

Mar 31, 2011 | 2000 Nissan Frontier

3 Answers

Both my right & left turn signals aren't working but hazards are


If you can locate the hazrd flasher unit under the dash on the drivers side, the turn flasher unit should be right beside it and looks the same. Unplug and switch the 2 flashers and see if the turn signals work. The flasher unit is a silver and round. they are usually close to the stering colum. Let me know if that helps.

Mar 27, 2011 | Dodge Durango Cars & Trucks

1 Answer

Turn signals and hazard lights won't work. already replaced flasher unit and burnt bulbs but still no turn signals


Check the Fuse box loacted inside the hood. Look for the guidance on the top of the fuse box for locating trun signal fuses.

Check whether they are good. If not replace with correct rating fuse. If the problem is not solved still, wiring harness has to be checked as the bulbs & flashers are replaced already.

Jun 04, 2010 | 2002 Hyundai Accent

3 Answers

The blinkers and flashers are not working on my 2001 Grand Cherokee. Can you tell me where to locate the relay or switch to replace? Its not the fuse, we checked that first. thank you


when you get in your car and use the car turn signals and it does not work from the inside or out side and your hazard light dont work to then you need to replace the fuse located inside the front hood in a black box or inside the car located under the stering wheel next to the gas and brake pedle on the side. Remove it and check the fuses and flasher relay. The flasher relay in a black square looking fuse that has 3,4, or 5 prongs. That is your problem of why the hazord lights and blinkers are not working, you can go to a part store to find the flasher relay for 9 to 15 dollars max. Napa has more of a selection. PS.... when you find the flasher and its burn out it is no good ; make sure the volts match!!!! If you buy a flasher and it burns out instinly after replaced then wireing is short and go with less volts you hace to ballance things of your car was worked on before, things where changed. Check you lights in front and back brights and dim, brakes and reverse lights. replace bulbs if needed could correct the problem if flasher still doesnt let blinkers or hazord work. If bulbs where replaced and still no blinkers or hazord lights then you need a new or used (another) switch nob. You can go to a local junk yard and take off what you need off the same car you have and pay for it then replace it on your car. Or you can go to amazon ebay or such to find. If you are a WOMEN or OLDLADY or some one not good at removing parts then this is not your job. Find someone who can help, or pay something that could be so easyily done. I hope this solves your question.

Mar 31, 2010 | 2001 Jeep Cherokee

3 Answers

Signal lights work intermittently


For an intermittant problem I'd recommend removing the flasher unit -- it is plugged into a socket, so you can just pull it out.

Clean the contact pins on the flasher and replace it in the socket.

That should do the trick.

May 27, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Turning signals not working


The way the system works is:
The fuse supplies 12 volts to the flasher unit then leaves the flasher and goes to the turn-signal switch in the steering column.
When you set the turn-signal switch to turn right or left, the switch sends that 12 volts to the front and rear bulbs. The voltage goes through the bulb, lighting the bulb and goes to ground.
If any of these components are not good than the lights will not work.
Check the fuse and make sure it is good, the fuse will be located under the hood at the fuse center.
Let me know if you have a test light and we can proceed from there.
Regards,

May 09, 2009 | 2001 Chevrolet Blazer

4 Answers

Front driver side turn signal light doesn't flash.replaced bulb,replaced socket,all other lights work on emergency flasher,except front driver side.rear driver side turn signal light works,but flashes...


replace flasher......usually located in fuse block area...listen in this area....select passenger side ...then select driver side...you can hear flasher clicking...you have seperate flashers for each...FLASHERS are small cubes plugged into fuse block....probable bad driverside flasher

May 09, 2009 | 1998 Buick Century

1 Answer

Turn signal problems


Turn signals have a relay (its a small switch that charges and discharges current) which controls your turn signals blinking speed and interval. This is most likely your problem. You should be able to get a new one at your local parts store. Follow these instructions, in this order, and let me know how it works.

Step 1:Turn on the hazard lights and walk around the Taurus checking that all four turn signal lights are working. If any of them are not working, replace the bulbs. A non-working bulb in any of the turn signals will often make the turn signals appear that a flasher is going bad.

Step 2:
Locate the fuse box and check the fuses for the turn signals. There may be more than one. Replace any fuses that are blown and then recheck the turn signals again. If they still aren't working properly, then move on to replace the flasher. Step 3: Look for a round, silver-colored object near the fuse box. Put your finger on the object and turn on the turn signal. You should be able to feel a mechanical clicking as the turn signal blinks. This is the flasher. Step 4: Pull the silver flasher out of the socket and replace it with the new one. Each of the flashers should have two pins sticking out of the bottom side. Start the Taurus and recheck the turn signals to ensure that they work. Joel

Mar 04, 2009 | 1999 Ford Taurus

1 Answer

Trun signal no op. fuse good and bulbs good


are the turn signals not working on both sides? If yes, replace the turn signal flasher, located on the fuse block.

Nov 29, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...