Question about 1997 Honda Accord

1 Answer

I want to remove the right front fender and would like to know where all the nuts and bolts etc. that need to be removed are and the easiest way of going about it?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 23 Answers

I just did this.
Remove the fender liner
Remove the mud guard

There are several 6mm flange bolts with 10mm heads.
3 along the inside of the hood
1 behind the top of the door accessible with the door open
2 on the bottom of the door behind the mud guard
2 behind the bumper cover, the headlight is attached to one of these.
There is a screw holding the end of the bumper to the fender. Remove it and pull the cover away from the fender. There is a large plastic clip inserted into the fender next to the two bolts that holds the bumper cover but should release when you pull the cover.

The headlight has two dowel pins that insert into the fender, removing the headlight may be better but you have to remove the bumper to get to some of the headlight assembly bolts. There are 4 bolts holding on the bumper that are accessible through the turn signal holes. The bumper will "fall" about an inch and sit on some collar bolts so it can be lifted off without one side falling (a neat feature). The turn signal is held by one Phillips screw accessible through a special hole on the inboard side of the bumper with your longest Phillips screwdriver.

Posted on Jun 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alternator removal 1998 ford taurus dohc


3.0L (4V)
Removal
  1. Disconnect the battery ground cable.
  1. Remove the accessory drive belt from the generator pulley.
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist.
  1. Remove the right front wheel.
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.

Nov 08, 2009 | 1998 Ford Taurus

1 Answer

Remove left front fender 1967 Chevelle


There are quite a few bolts on this fender. One on the bottom of the rocker, one between the the door and fender on the "A" pillar, one on the cal, one on the firewall then several on the inner fender and several on the radiator core support. after these are removes you need to take ou the head light assembly and you should have a fender brace under the front of the car. Hope this helps.

Oct 06, 2009 | 1983 Chevrolet Malibu

2 Answers

Need to change cv outer boot on mazda ba 94 model.


it just pulls out. it hasa circlip that holds it in on driver side. which side?

here's an escort, should be similar. note step 17

Removal
  1. Raise and support the vehicle.
  1. Remove the lug nuts (1012) and the front wheel and tire assembly.
  1. Remove the front fender splash shield bolts and the front fender splash shields (16103) .
  1. Use a small cape chisel to carefully raise the staked portion of the front axle wheel hub retainer (3B477).




  1. Remove the front axle wheel hub retainer and discard it.
  1. Remove the cotter pin and the tie rod end nut from the tie rod end (3A130). Discard the cotter pin.




  1. Use an appropriate tie rod end remover to separate the tie rod end from the front wheel knuckle (3K186).




  1. Remove the ball joint bolt and the ball joint bolt nut.




  1. Carefully pry down on the front suspension lower arm (3078) to separate the front suspension lower arm ball joint (3050) from the front wheel knuckle.




  1. Pull outward on the front wheel knuckle (3K185). Carefully pull the front wheel driveshaft and joint from the front wheel knuckle and position it aside.




  1. NOTE: Removal of the LH front wheel driveshaft and joint (3B437) requires removal of the transmission support crossmember (6A023) to allow access with a pry bar. If the LH front wheel driveshaft and joint is being removed, continue with step 11. If the RH front wheel driveshaft and joint is being removed, continue with step 15.

    Support the transaxle with a transaxle jack or equivalent.
  1. Remove the four transaxle mount-to-rear engine support nuts.




  1. Remove the two rear engine support nuts at the rear of the transmission support crossmember.
  1. While supporting the rear of the transmission support crossmember remove the two rear engine support bolts. Remove the transmission support crossmember.




  1. Position a drain pan under the transaxle.
  1. Insert a pry bar between the front wheel driveshaft and joint and the transaxle case.
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Extreme care must be taken to ensure that the pry bar does not damage the transaxle case, the transaxle oil seal, the front wheel driveshaft and joint, or the front wheel driveshaft joint boot (3A331).
    Gently pry outward to release the front wheel driveshaft and joint from the differential side gears (4236).




  1. Remove the front wheel driveshaft and joint.




  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When the LH and RH front wheel driveshaft and joint assemblies are removed, Transaxle Plugs T88C-7025-AH must be inserted to prevent the differential side gears from becoming mispositioned. If the gears become misaligned, the differential will have to be removed from the transaxle to align the gears.
    If both front wheel driveshaft and joints were removed, install Transaxle Plugs T88C-7025-AH in the differential side gears.
  1. Remove and discard the driveshaft bearing retainer circlip (3Z498).

Oct 03, 2009 | 1994 Mazda 323

2 Answers

How do I remove the drivers front fender of a 1994 Dodge Ram 2500


yes undo your battery as ans air bag has a connector on the seat and if unplugged could cause air bags to go off with battery still hooked up leat sit for five min. should be four bolts or nuts holding seat down

Sep 15, 2009 | 1998 Dodge Ram

1 Answer

How to 1998 Taurus altenator R&R


please rate highly if this helps
Generator 3.0L (2V)
Removal
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  2. Remove the right front wheel. Refer to Section 00-02 .
  3. Remove the lower fender splash shield retainers and position the shield out of the way.
  4. Lower the vehicle.
  5. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  6. Remove the power steering line bracket and heater hose support bracket from the generator.
  7. Remove the upper generator bolts.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Disconnect the right hand stabilizer link.
  15. Lower the subframe to provide clearance.
  16. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Connect the right hand stabilizer link and torque to 47-62 Nm (35-46 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B + cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
3.0L (4V)
Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 14-01 .
  1. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  1. Remove the right front wheel. Refer to Section 00-02 .
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.
3.4L (4V)
Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the right side cowl vent screen. Refer to Section 01-02 .
  1. Raise the vehicle and remove right front wheel assembly. Refer to Section 00-02 .
  1. Remove right tie-rod. Refer to Section 11-02 .
  1. Remove accessory drive belt (8620) from generator. Refer to Section 03-05 .
  1. Disconnect electrical harness connector and output terminal wiring.
  1. Remove nut and position engine control sensor wiring (12A581) out of the way.
  1. Remove the two bolts and one stud bolt.
  1. Remove generator from vehcile

May 12, 2009 | 1998 Ford Taurus

3 Answers

Replace front fenders 1999 wrangler


Take off the tyre and remove the plastic inner fender first.

Mar 17, 2009 | 1999 Jeep Wrangler

1 Answer

Replacing the Right Front Fender on a 1999 Mazda 626


Can you remove the wheel well splash shield and get access to the bolts? Body shop techs have a special tool to get into this area.

Here's a 97 Probe whcih was the same as a 626 in 1997:

Fender, Front Removal
  1. On GT models, remove the side sill extension. Refer to Section 01-08 for the removal and installation procedure.
  1. Remove the front fender bolt located in the door jamb opening.


    RH Side Shown, LH Side Similar


    b7b1239.gif

  1. Remove the three upper front fender bolts located on top of the front fender (16005) inside the engine compartment.
  1. Raise and support the vehicle.
  1. Remove the wheel (1007).
  1. Remove one push pin and five front fender splash shield bolts and remove the front fender splash shield (16102).
  1. Remove the upper front fender brace screw.
  1. Remove the inner front fender bolt.
  1. Remove the screw holding the front bumper cover (17D957) to the front fender.
  1. Remove the two lower front fender bolts.
  1. Remove the front fender.
Installation
To install, reverse the removal procedure. Tighten the front fender bolts to 7-9 Nm (61-86 lb-in).

Feb 24, 2009 | 1999 Mazda 626

1 Answer

What is the easiest way to replace the driver?s side front fender?


remove the splashsheild on fender first/remove bolt at fender 10mm then take out the bolts on the apron and then open the door you will find a bolt there and one at the bottom of fender at rocker /thats it please rate my response thank you very much

Jan 30, 2009 | 1995 Hyundai Sonata

1 Answer

How do I remove a wrecked front fender assy/quarter panel?


The front fenders are connected to the A pillar above the the top hinge, at the bottom of the rocker panel seam, three bolts pass through the hood hinge support in the middle of the fender, four bolts on the radiator support, three vertical bolts on the top radiator brace, and one bolt at the rear of the wheelhouse to the cab body. Yes, the wheelhouse is spot welded to the fender and must be removed with it. Remove all the bolts listed as well as the bolts retaining the splash shield. The splash shield is a plastic liner connected to both the wheelhouse and the fender. Remove the headlight/cornering lamp assembly. The best way I have found to do this is to loosen the bumper to framebrackets and let the bumper assembly sag to gain clearance. If the upper bumper cover is removed to gain the clearance needed you will more than likely need to get a new cover as the nylon clips have a tendency to break during removal. Once the fender/wheelhouse assembly has been removed use a spot weld cutter to separate the wheelhouse from the old fender. Check the new fender for clearance and fit on the vehicle. Make all the needed adjustments to get the fender to fit correctly. Remove the fender and attach the wheelhouse. This should be done by spot welding. It can also be done using bolts. If using bolts place some 3M double stick weather strip adhesive tape in the seam to prevent direct contact of the parts to prevent rattles and squeaks. Drill the new fender to match the holes made by the spot weld cutter in the wheelhouse. Use stainless bolts and lock nuts so that the assembly can be services if needed. I would also recommend using Wurth Rust Inhibitor on all the seams to prevent rust and once cured it is an excellent adhesive and will reduce noise coming from moving body panels. Good Luck. It is not as bad as it sounds. Take your time and it will be worth the effort.

Jan 14, 2009 | 1998 Dodge Ram

1 Answer

Front struts replacement


Jack up and secure front end of your vehicle,Take off two front wheels. Loosen to bolt on the bottom of struts (Its a bolt and nut). Remove clip that holds brake hose on to strut and remove hose. DO NOT OPEN BRAKE LINE OR DISCONNECT FROM CALIPER. Remove bolts and remove bottom of strut from knuckle/Hub assembly. Then loosen nuts on strut tower( on top of fender inside hood) (3) nuts, mark exact locations of each nut on strut mount area on upper fender weld. Make sure to hold strut on the bottom so it doesn't drop down on caliper and knuckle or on you possibly.YOU WILL NEED A SPRING COMPRESSOR to compress spring so you can take struts off. MAKE SURE THAT SPRING IN COMPRESSED/SQUEEZED WITH A STRUT COMPRESSOR. Then loose center nut on strut tower(may be covered with a circular rubber cover) If nut spin around with out getting loose use vise grips to hold strut rod ONLY TO REMOVE STRUT NOT TO INSTALL. if you use vise grips to install it will damage strut. When nut is off, remove strut and reinstall new one transfer all rubber boots and cushions from old strut. Good Luck thanks for using FIX-YA.com contact me if you need more help.

Dec 30, 2008 | 2004 Nissan Altima

Not finding what you are looking for?
1997 Honda Accord Logo

1,027 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...