Question about 2001 Chrysler Town & Country

1 Answer

How do you change drivers side rear view mirror on 01 T&C Limited

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,297 Answers

  • remove the door trim at the mirror
  • remove the three bolts holding the mirror assembly
  • disconnect the electrical connector (assuming its powered mirror)
  • remove the mirror and replace

Posted on Jun 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear view mirror dims at Startup


That is some vehicle coming with diming rear view mirror n also side view mirror. pls check your vehicle specification.

Dec 20, 2013 | 2002 GMC Envoy

1 Answer

HOW DO I REPLACE THE REAR VIEW MIRROR ON MY 1999 BUICK LESABRE LIMITED


  • Push the mirror lens upward so it faces the roof of your Buick LeSabre.

  • Place the eight-pointed star head of the Torx driver into the setscrew located in the base of the rearview mirror. Turn the Torx driver counterclockwise. This releases the clamping pressure on the mirror.

  • Slide the mirror upwards to remove it from its metal bracket.

  • Place the base of the replacement mirror against the windshield, directly above the metal bracket. Slide the mirror down into the bracket. The bracket has a groove on each side into which the mirror will slide.Secure the mirror to the bracket by tightening the setscrew clockwise with the Torx driver.



  • May 04, 2011 | 1999 Buick LeSabre

    1 Answer

    Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


    Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
    1. Disconnect battery ground cable (14301).
    1. Remove front door trim panel (23942). Refer to Section 01-05.
    1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
    1. Remove two screws from cover assembly.
    1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
    1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


    an0786b.gif


    Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
    AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
    AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
    AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
    AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
    BAW Speaker Grille-Mach-LH 5 F8DB-18978-
    BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
    AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
    AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
    Trim Panel, Door Front
    Removal
    1. Remove cover behind inside door handle.
    1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
    1. Remove three screws retaining front door trim panel to front door.
    1. NOTE: Do not attempt to remove more than one pushpin at a time.

      Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
    1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
    Installation
    1. Follow removal procedure in reverse order.
    1. Replace all pushpins with new pushpins (N808994-S).
    Front Door Trim Panel


    ar0318d.gif

    Jan 14, 2011 | 1999 Ford Taurus

    1 Answer

    Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


    here's 1996, all I have. Please rate.

    Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

    Removal
    1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
    1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




    1. Remove the wire clip.
    1. Disconnect the power outside rear view mirror electrical connector.




    1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




    Installation
    To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
    Removal and Installation
    Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
    Removal
    1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
    1. Remove the two outside rear view mirror inside mounting hole cover screws.


      Remove the outside rear view mirror mounting hole cover.
    Installation
    To install, reverse the removal procedure. Mirror Control
    Removal
    1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


    May 13, 2010 | 1995 Mercury Villager

    1 Answer

    2002 Mountaineer. How do you change the light bulb at the bottom of the driver side rear view mirror. Dan


    SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
    NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.

    NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
    All mirrors
    1. Position the glass in the full up position.
    1. Locate the notch at the bottom of the exterior mirror glass.
    ed6be7c.gif
    1. Release the exterior mirror glass.
      1. Insert a long flat-bladed screwdriver in the notch.
      1. Push the screwdriver into the notch until the glass is released.
    Heated mirrors
    1. Position aside the exterior mirror glass.
    1. Disconnect the electrical connectors.
    All mirrors
    1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
    Installation
    Heated mirrors
    1. Connect the electrical connectors.
    All mirrors
    1. Position the exterior mirror glass on the exterior mirror motor.
    1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

    Dec 26, 2009 | 2002 Mercury Mountaineer

    1 Answer

    How do i replace left door mirior


    remove trim panel, remove mirror fasteners.

    Glass, Outside Mirror—Town Car

    Removal and Installation
    1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
    1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
    1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
    1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
    1. To install reverse Removal procedure.
    ------------------------------------------------------------
    Mirror, Power—Outside Rear View
    Town Car

    Removal and Installation
    1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    1. Remove front door trim panel (23942). Refer to Section 01-05 .
    Trim Panels, Door Front—Town Car
    Removal
    1. Snap out two door pull strap retaining screw covers. Remove screws.
    1. Remove three screws on front and rear side and center of front door trim panel (23942).
    1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

      Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
    1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

      Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
    1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
    1. Remove the door trim panel.
    1. Disconnect two electrical connectors.
    1. Remove nut from outside rear view mirror mounting base.
    1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
    1. Remove screw from outside rear view mirror base.
    1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
    1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

    Nov 05, 2009 | 1996 Lincoln Town Car

    1 Answer

    Heated mirrors are not adusting


    could be a blown fuse. Take it into the dealership.. it's probably still under warranty!

    May 25, 2009 | 2007 Hyundai Santa Fe Limited

    1 Answer

    99 explorer drivers side mirror vibrates


    are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

    1. Remove the front door trim panel; refer to Section 501-05 .
    2. go to car-part.com for a used mirror. Page with * is cheapest seller.
    1. Remove the speaker.
      1. Remove the screws.
      1. Disconnect the electrical connector.
      1. Remove the speaker.
    1. Remove the outside rear view mirror (17682).
      1. Disconnect the power mirror wiring clips.
      1. Remove the outside rear view mirror nuts.
      1. Remove the outside rear view mirror.
        • Feed the power mirror wiring through the opening in the front door (20124).
    ------------------------------------------------------
    f9d70e9.gif
    ----------------------------
    SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
    REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
    NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
    NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
    All mirrors
    1. Position the glass in the full up position.
    1. Locate the notch at the bottom of the exterior mirror glass.
    1. Release the exterior mirror glass.
      1. Insert a long flat-bladed screwdriver in the notch.
      1. Push the screwdriver into the notch until the glass is released.
    Heated mirrors
    1. Position aside the exterior mirror glass.
    1. Disconnect the electrical connectors.
    All mirrors
    1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
    Installation
    Heated mirrors
    1. Connect the electrical connectors.
    All mirrors
    1. Position the exterior mirror glass on the exterior mirror motor.
    1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
    4d9527f.gif

    Apr 12, 2009 | 1999 Ford Explorer

    1 Answer

    Replace driver side mirror on 2001 Nissan Quest


    SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
    1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
    1. Remove the upper speaker.
      1. Disconnect the electrical connector.
      1. Remove the bolts.
      1. Remove the speaker.
    1. Position the watershield aside.
    1. Remove the exterior rear view mirror access panel.
    1. Disconnect the exterior rear view mirror electrical connectors.
      • Release the wiring harness locator.
    1. Remove the exterior rear view mirror.
      • Remove the bolts.
      • Feed the wiring harness through the door opening.

    Mar 31, 2009 | 2001 Nissan Quest

    1 Answer

    Side Mirrors will adjust side to side but not up and down.


    There are two tiny motors in each mirror. one for up/down. One for side to side. They have jack screws (plastic) that fit into the motors.

    You can manually put your hands on either side of the mirror and force adjust it. If you hear a ratcheting sound, the jack screws are OK. Then repeat with hands on top and bottom.

    If you hear ratcheting and mirror stays where you stop it, that means one of the motors is bad. The motor assembly is available as a separate part.

    -------------------------------------------------------------------------------------
    Mirror Motor—Crown Victoria, Grand Marquis
    Removal and Installation
    1. Disconnect battery ground cable. Refer to Section 14-01 .
    1. Remove outside Rear View Mirror Glass as outlined.
    1. Remove Outside Rear View Mirror as outlined.
    1. Remove two screws from outside rear view mirror motor.
    1. Remove outside rear view mirror housing from outside rear view mirror base.
    1. Disconnect connector and remove outside rear view mirror motor from mirror housing.
    1. To install, reverse Removal procedure.
    1a865db.gif
    Might be cheaper to buy used irror at car-part.com. Look for * to find page with cheapest part. Or, EBay. Good luck

    Aug 11, 2008 | 1996 Ford Crown Victoria

    Not finding what you are looking for?
    2001 Chrysler Town & Country Logo

    215 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...