Question about 1998 Ford Ranger SuperCab

Open Question

Remove Dashboard on a 1998 Ford Ranger. I have to replace the HVAC Box

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: torque specifications for 1998 ford ranger

Okay...here is a list since no motor size:

2.5L----- 56-64

3.0L----- 56-64

4.0L----- 59

5.0L----- 75-85

All in ft lbs.......this is for the flywheel.

Posted on Apr 05, 2009

Ad
seans46
  • 161 Answers

SOURCE: Location of GEM Module on 1998 Ranger

i am almost sure it is in steering col area by firewall. but call any part store like auto zone and they can print it out and tell you if your ford dealer wont. but on the fords they usualy are all in the drivers steering area sometimes way up by fire wall

Posted on Jun 15, 2009

  • 104 Answers

SOURCE: how to install replacement door handles for 98 ford ranger pickup

remove interior door panel(need special tool to pop plastic clips holding panel to door)with panel off remove plastic film,with window up you should be able to see two 10m nuts-bolts to remove-also have to pop lever off that goes down to door latch

Posted on Sep 19, 2009

johnjohn2
  • 5763 Answers

SOURCE: where can i find a fuse box diagram for a 1998

in your owners manualy, or a ford ranger website .good luck.

Posted on Oct 12, 2009

  • 1 Answer

SOURCE: How do you remove the dashboard completely on 2005 ford explorer?

how to remove dash on 2055 ford explorer

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace instrument panel bulb


How to Replace an Instrument Panel Bulb - YouTube

? 14:56
https://www.youtube.com/watch?v=Rwj74yo2knY
Jun 15, 2013 - Uploaded by Schrodingers Box
Removal of an instrument panel cluster on 1996 Ford Ranger to... 1999 Ford Ranger: How to change dash board lights, walk through part 1 ...

How to Replace Dashboard Lights : Removing ... - YouTube

? 2:42
https://www.youtube.com/watch?v=zzxz7iG81kI
Sep 18, 2008 - Uploaded by expertvillage
Use socket wrench to loosen dashboard bolts. Learn about technique for installing dashboard lights in a 1996 Ford Explorerin this free auto repair series fr. ... do you need to remove the radio bezel to get to the clips?? will this ...

How to Replace Dashboard Lights : Removing ... - YouTube

? 2:30
https://www.youtube.com/watch?v=QJWoJ17liQI
Sep 18, 2008 - Uploaded by expertvillage


Dec 16, 2015 | 1996 Ford Explorer

1 Answer

How do you remove the dashboard on a 1992 Ford Ranger


Have the windscreen resealed, you don't want to remove the dash, that takes all day.

Oct 16, 2012 | 1992 Ford Ranger

2 Answers

05 ford ranger 3.0......if I put my thermostat on cold...the vent blows hot air..on max ac..its cold air..makes no sense right....help


Cold air like, really cold or just cool. Sounds like your hot/cold blend door motor has perhaps failed with the blend door in the semi hot position. Blend door motor failure is very common on the Ford truck HVAC systems. Is is located behind the glovebox on top of the HVAC housing assembly.

May 19, 2011 | 2005 Ford Ranger

1 Answer

Problem with dual zone heating only one side i check control thermost botton is ok


Sounds like the blend door actuator. It separates the driver and passenger side from getting air on the AZC system. Here are some instructions on replacing it:
The passenger side blend door actuator is used on all models equipped with Automatic Zone Control (AZC). This actuator is located on the front of the HVAC housing to the right of the floor panel transmission tunnel and cannot be removed from the passenger compartment without instrument panel or HVAC housing removal.

NOTE: This procedure is for AZC Systems (Passenger side only).

  1. Disconnect and isolate the battery negative cable.
  2. Remove the glove box door. See: Body and Frame\Interior Moulding / Trim
  3. Remove the lower I/P glove box door surround panel.
  4. Remove the dash assembly. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Remove the HVAC assembly. See: Housing Assembly HVAC\Service and Repair
  6. Unplug the wire harness connector from the blend door actuator.
  7. Remove the 2 screws that secure the blend door actuator to the HVAC housing.
  8. Remove the blend door actuator from the HVAC housing.
INSTALLATION - AZC (Passenger side only)


  1. In stall the blend door actuator on the HVAC housing and tighten the two mounting screws to 2.2 Nm (20 in. lbs.).
  2. Plug in the wire harness connector to the blend door actuator.
  3. In stall the HVAC unit into the vehicle. See: Housing Assembly HVAC\Service and Repair
  4. Install the instrument panel assembly into the vehicle. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Evacuate the HVAC system.
  6. Recharge the HVAC system.
  7. Connect and the battery negative cable.
Hope it helps! If you need more, just send me an email at familyguy77351 at yah I wil be glad to finish helping you with more detail.

Dec 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Replacing heater core 98 ford ranger


this is not a fun job. You need to remove the front cover (facing you) under the dash of the heater box. Usually 8 to 10 screws and not all are easy to reach. Then drain the rediator and remove the two hoses at the firewall that attach to the heater core. Once this is achieved the core slides out easily. sounds easier than it is. good luck

Apr 25, 2010 | 1998 Ford Ranger SuperCab

1 Answer

Where can i find a fuse box diagram for a 1998 ford ranger


in your owners manualy, or a ford ranger website .good luck.

Oct 12, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Trying to put a heater core in a 1998 ford ranger and don't know how. Do you have a diagram to go by. step by step. thank you.


Disconnect heater hoses. Remove glove box. Remove cover fro heater core (8mm screws) . Remove parts in way of cover. Replace heater core. reassemble. I would recommend flushing system first. Top off coolant.

Oct 04, 2009 | 1998 Ford Ranger SuperCab

1 Answer

How to install replacement door handles for 98 ford ranger pickup


remove interior door panel(need special tool to pop plastic clips holding panel to door)with panel off remove plastic film,with window up you should be able to see two 10m nuts-bolts to remove-also have to pop lever off that goes down to door latch

Sep 19, 2009 | 1998 Ford Ranger SuperCab

1 Answer

Hard tonneau cover


I guess I should have checked it out before posting this. It was easy. It was just a matter of clamping the rails to the sides and front of the box, sliding the cover into the 2 slots in the front, and voila!

Aug 27, 2008 | 1998 Ford Ranger SuperCab

1 Answer

Door handle on 1998 Ford Ranger


Remove the door panel and on the inside of the door is a clip or a couple of nuts you'll need to remove. The door handle will fall out.

Jun 14, 2008 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
1998 Ford Ranger SuperCab Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...