Question about 2003 Mazda MPV

1 Answer

Brakes don't work right. I have bleed them about three times. I have a padel but it's spungy

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,374 Answers

You may have an internal leak inside of master cylinder. Have it check out by a repair shop.

Posted on Jun 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I converted my 82 jeep cj 7 manual brakes over to power now i dont have a good pedal why?


vacuum ok to booster
bleed it all 3 ways.? then bleed again?

the booster still allows manual brakes to work with a hard padel
so , bleed it until it does. is the free play on the rear of the MC
set to spec. I bet not.
there must be free play there or the brakes will lock up.
do not ALLOW that to ever HAPPEN
great danger waits to those that dont set up brakes rigtht.

Aug 31, 2014 | Jeep CJ7 Cars & Trucks

1 Answer

Bleed brakes


This will give you a all the Right Way to get the job don Right good luck
http://www.stoptech.com/technical-support/technical-white-papers/bleeding-brakes

Jun 15, 2013 | 1996 Pontiac Sunfire

1 Answer

Do you have to used VAG 1869/2 tool brake depressor to bleed brakes on a VW 2007 EOS ?


thats too much hard work dude!,go to an auto parts store and buy a one man bleeder kit,the hand vacuum style works the best.looking at only about 25 to 30 bucks for it,and it will pump the fluid in front of your face till no bubbles are present,just keep the master cylinder full!!,you can leave the cap off the master while doing this.

Mar 04, 2013 | 2007 Volkswagen EOS Convertible

1 Answer

How to bleed the brakes alone on a 00 maxima


The pedal should not feel that way if you just changed the pads, you must have another issue like a master cylinder

May 30, 2012 | 2000 Nissan Maxima

1 Answer

Still cant get a brake pedal.. been bleeding the lines but not getting much out of them. replaced master cylinder, still no pedal. has all new lines also


you may have to run the motor as you bleed the brakes so the abs hydraulic unit can purge any air that might be caught within the unit itself.did you bench bleed the master cylinder before installing it on the car.this can save time and reduce the possible chance of air entering the system.make sure you don`t allow the master cylinder to run low on brake fluid.i also assume that you are bleeding the brakes properly.Left front brake works with Right rear brake and Right front brake works with Left rear brake.this is how the brakes should be bleed.

Mar 15, 2011 | 1997 Buick LeSabre

2 Answers

I relaced all brake pads on 2003 buick bleed brakes very little air my brake peddle still spungy and anti brake light stays on


you must re-bleed the system properly, especially the back brakes. Bring your vehicle to a local autozone to reset the ABS light or check for an ABS fault code and post it on fixya!!

Sep 27, 2010 | Buick Rendezvous Cars & Trucks

1 Answer

Troublelight -brakes


Check your master cylinder it may need to be replaced.

Mar 01, 2010 | 1985 Mercury Grand Marquis

1 Answer

I have replace wheel cylinder on 97 Stratus, bleed the brake several times, but the brake pedal seems to get more spongy every time I bleed. Could the master cylinder possibly need replace? Is there a...


Itsw very unlikely their is a problem with the master cylinder. When you pump the brake's to bleed them it uses up the vacuum and the brakes will be spungy because the servo isnt working properly. After bleeding leave it running for a few minutes then try the pedal it should be ok. If their is a problem with the master cylinder then the pedal would go all the way to the bottom but not spungy. You may need to bleed the brake on the other side to get all the air out of the system.

Sep 15, 2009 | 1997 Dodge Stratus

3 Answers

Brake pedal goes too far down. Brakes still stop car fine. Too much pedal travel. 2005 model year.


You have to check your master cylinder, pump your brake several times and hold it, see if is going down to the bottom, if does, the master cylinder is wrong, check the brake pressure hose, maybe you have some air in your brake lines, be sure you have enough brake fluid

Jul 27, 2008 | 2004 Toyota Camry

Not finding what you are looking for?
2003 Mazda MPV Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...