Question about 2004 Chevrolet Silverado 2500HD

Open Question

Where is the horn on a 2004 silverado 2500HD diesel

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fyrebyrd1
  • 121 Answers

SOURCE: replacing starter 02 silverado 6.6

  1. Remove or disconnect the following:
    • Negative battery cables
    • Right front wheel and fender splash shield, on 6.6L engines
    • Turbocharger exhaust pipe, on 6.6L engines
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152801cad96.jpgExploded view of the starter motor-6.5L engine shown
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires.Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18inch lbs. (2 Nm) on 6.5L engines. On 6.6L engines, tighten the solenoidnut to 30 inch lbs. (3.4 Nm) and the positive battery cable nut to 80inch lbs. (9 Nm).
    • Starter
    • Mounting bolts/nuts and shim,if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inchlbs. (8.5 Nm) for 6.5L engines. For 6.6L engines tighten the starterbolts to 58 ft. lbs. (78 Nm).
    • Turbocharger exhaust pipe, on 6.6L engines
    • Right front fender splash shield and wheel, on 6.6L engines
    • Negative battery cables

Posted on Nov 05, 2008

Ad
  • 37 Answers

SOURCE: CHEVY SILVERADO 2500HD DURAMAX DIESEL

DTC P1093
Fuel Rail Pressure Low During Power Enrichment



The engine control module (ECM) uses the fuel rail pressure (FRP) sensor to determine fuel pressure to the fuel injectors. This is then compared to the calculated target fuel pressure as determined by the ECM. The ECM adjusts the FRP by modulating the duty cycle of the control driver of the fuel pressure regulator. Injector pulse duration is determined by the measured rail pressure and the target injection fuel into each cylinder. If a sensor circuit malfunction is detected, or the commanded fuel injection pump flow is not within the proper range for a given engine load and speed, DTCs will be set.

DTC U1000 and U1255 Circuit Description Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. When a module does not associate an identification number with at least one critical parameter within about five seconds of beginning serial data communication, DTC U1000 or U1255 is set. When more than one critical parameter does not have an identification number associated with it, the DTC will only be reported once. The class 2 serial data line on this vehicle is a ring/star configuration. The following modules communicate on the class 2 serial data line:
• The body control module (BCM) • The digital radio reciever • The driver door module (DDM) • The electronic brake control module (EBCM) • The front passenger door module (FPDM) • The HVAC control module • The inflatable restraint sensing and diagnostic module (SDM) • The instrument panel cluster (IPC) • The memory seat module (MSM) • The powertrain control module (PCM) • The radio • The radio amplifier • The rear seat audio (RSA) controller • The rear seat entertainment (RSE) assembly w/U42 • The rear wheel steering control module • The remote playback device-CD player w/U1S • The transfer case shift control module • The transmission control module (TCM) w/Allison transmission • The theft deterrent control module • The vehicle communication interface module (VCIM) w/UE1

Posted on Dec 09, 2008

  • 548 Answers

SOURCE: where is the horn located under the hood of my 2008 chevy truck?

Have a friend, (or in-law) someone you're not too fond of, stand in front of the truck while you honk the horn and have them pinpoint it for you.

Posted on Dec 29, 2008

Auto Master
  • 139 Answers

SOURCE: Need to know Oil Capacity for Duramax 6.6 in 2004

Hello,
The requirement is 10 QTS. I use 10 and check it cause some times they hold 11 QTS. I hope this helps. If you have more questions reguarding this or other conserns please ask me. Please remember high ratings are very important to me.

Thank You,
Roy

Posted on Aug 28, 2009

Testimonial: "Thanks very much for that Regards Bryan McRae New Zealand"

  • 108 Answers

SOURCE: reduced engine power shows up on my 2004 chevy

This problem is directly related to the APP (Accelerator Pedal Position) Sensor and the associated Module located on the Firewall immediately to the Left side of the Power brake booster unit. Disconnect the Negative Battery Cable before doing anything else! The Gray Connector is the one closest to the Left Front Fender. All of the leads to this connector are associated with the Accelerator Pedal Position Sensors and many other circuits controlling the electronics which operate the Air Valve Butterfly located on the front of the Intake Plenum. Corrosion of the contacts in the Gray Connector is common. Carefully clean the contacts, re-assemble the connector, re-connect the Negative Battery Cable and start the engine. If the problem is gone you should be home free. Another cause is Squirrels or Chipmunks eating through the insulation of the wires inside the Plastic Wire Loom. In my case this was what happened and I had to splice 6 of the wires which had been eaten through and broken. There are numerous Factory Service Bulletins covering related problems including a Program Update of the ECM.

Good luck,

Fastest Robe

Posted on Apr 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of thermostats on 6.6litre diesel


Top front of engine there inside a housing there is a heater tube going to them.

Feb 02, 2012 | 2004 Chevrolet Silverado 2500HD

2 Answers

Chevrolet 2004 Silverado 2500HD 6.6 wont start


try priming the fuel filter, ther is a pump and bleed scew above the filter, pump a few times hold the pump down open screw and se what comes out air or diesel? keep doing this until its diesel

Mar 04, 2010 | 2004 Chevrolet Silverado 2500HD

1 Answer

2004 Chevy diesel with heated leather seat that quit working.


It is a fuse. Go into your owner manual to locate the fuse or just look in the fuse panel as they are labeled.

Mar 02, 2010 | 2004 Chevrolet Silverado 2500HD

1 Answer

Diagram for a sepintine routing belt (Chevy Diesel 2004)


this should help you, please leave a good feedback thankyou and good luck.
10846db.jpg

Jan 01, 2010 | 2004 Chevrolet Silverado 2500HD

3 Answers

Why would my 2004 Chevy Silverado 2500hd diesel go into "limp" mode?


limp??????????????????? If your talking lose of power. check the two filters 1st the one on the fire wall if not this one is the pain in the tank.

Dec 06, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

The air conditioning on my 2004 Chevrolet silverado 2500 hd diesel quits working and begins blowing hot air.


After checking the fuses and the relay, I would suggest that you pick up a charging kit for about 25-30 bucks at your nearest dept. store or auto parts store.

Sep 07, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

Alternator needs to be replaced


There is a spring tensioner on it.Pull back to loosen belt.The same to refit belt

May 30, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

Horn replace


have someone beep horn while you look for it.

Nov 30, 2008 | 2007 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...